Investigation of factors driving the costs of operating the 2020 Irish power system with large-scale wind generation

The main goal of this work is to determine the true cost incurred by the Republic of Ireland and Northern Ireland in order to meet their EU renewable electricity targets. The primary all-island of Ireland policy goal is that 40% of electricity will come from renewable sources in 2020. From this it is expected that wind generation on the Irish electricity system will be in the region of 32-37% of total generation. This leads to issues resulting from wind energy being a non-synchronous, unpredictable and variable source of energy use on a scale never seen before for a single synchronous system. If changes are not made to traditional operational practices, the efficient running of the electricity system will be directly affected by these issues in the coming years. Using models of the electricity system for the all-island grid of Ireland, the effects of high wind energy penetration expected to be present in 2020 are examined. These models were developed using a unit commitment, economic dispatch tool called PLEXOS which allows for a detailed representation of the electricity system to be achieved down to individual generator level. These models replicate the true running of the electricity system through use of day-ahead scheduling and semi-relaxed use of these schedules that reflects the Transmission System Operator's of real time decision making on dispatch. In addition, it carefully considers other non-wind priority dispatch generation technologies that have an effect on the overall system. In the models developed, three main issues associated with wind energy integration were selected to be examined in detail to determine the sensitivity of assumptions presented in other studies. These three issues include wind energy's non-synchronous nature, its variability and spatial correlation, and its unpredictability. This leads to an examination of the effects in three areas: the need for system operation constraints required for system security; different onshore to offshore ratios of installed wind energy; and the degrees of accuracy in wind energy forecasting. Each of these areas directly impact the way in which the electricity system is run as they address each of the three issues associated with wind energy stated above, respectively. It is shown that assumptions in these three areas have a large effect on the results in terms of total generation costs, wind curtailment and generator technology type dispatch. In particular accounting for these issues has resulted in wind curtailment being predicted in much larger quantities than had been previously reported. This would have a large effect on wind energy companies because it is already a very low profit margin industry. Results from this work have shown that the relaxation of system operation constraints is crucial to the economic running of the electricity system with large improvements shown in the reduction of wind curtailment and system generation costs. There are clear benefits in having a proportion of the wind installed offshore in Ireland which would help to reduce variability of wind energy generation on the system and therefore reduce wind curtailment. With envisaged future improvements in day-ahead wind forecasting from 8% to 4% mean absolute error, there are potential reductions in wind curtailment system costs and open cycle gas turbine usage. This work illustrates the consequences of assumptions in the areas of system operation constraints, onshore/offshore installed wind capacities and accuracy in wind forecasting to better inform the true costs associated with running Ireland's changing electricity system as it continues to decarbonise into the near future. This work also proposes to illustrate, through the use of Ireland as a case study, the effects that will become ever more prevalent in other synchronous systems as they pursue a path of increasing renewable energy generation.

The effects of formulation and processing on surface characteristics and functional properties of dairy powders

The objectives of this thesis were to (i) study the effect of increasing protein concentration in milk protein concentrate (MPC) powders on surface composition and sorption properties; (ii) examine the effect of increasing protein content on the rehydration properties of MPC; (iii) study the physicochemical properties of spraydried emulsion-containing powders having different water and oil contents; (iv) analyse the effect of protein type on water sorption and diffusivity properties in a protein/lactose dispersion, and; (v) characterise lactose crystallisation and emulsion stability of model infant formula containing intact or hydrolysed whey proteins. Surface composition of MPC powders (protein contents 35 - 86 g / 100 g) indicated that fat and protein were preferentially located on the surface of powders. Low protein powder (35 g / 100 g) exhibited lactose crystallisation, whereas powders with higher protein contents did not, due to their high protein: lactose ratio. Insolubility was evident in high protein MPCs and was primarily related to insolubility of the casein fraction. High temperature (50 °C) was required for dissolution of high protein MPCs (protein content > 60 g / 100 g). The effect of different oil types and spray-drying outlet temperature on the physicochemical properties of the resultant fat-filled powders was investigated and showed that increasing outlet temperature reduced water content, water activity and tapped bulk density, irrespective of oil type, and increased solvent-extractable free fat for all oil types and onset of glass transition (Tg) and crystallisation (Tcr) temperature. Powder dispersions of protein/lactose (0.21:1), containing either intact or hydrolysed whey protein (12 % degree of hydrolysis; DH), were spray-dried at pilot scale. Moisture sorption analysis at 25 °C showed that dispersions containing intact whey protein exhibited lactose crystallisation at a lower relative humidity (RH). Dispersions containing hydrolysed whey protein had significantly higher (P < 0.05) water diffusivity. Finally, a spray-dried model infant formula was produced containing hydrolysed or intact whey as the protein with sunflower oil as the fat source. Reconstituted, hydrolysed formula had a significantly (P < 0.05) higher fat globule size and lower emulsion stability than intact formula. Lactose crystallisation in powders occurred at higher RH for hydrolysed formula. In conclusion, this research has shown the effect of altering the protein type, protein composition, and oil type on the surface composition and physical properties of different dairy powders, and how these variations greatly affect their rehydration characteristics and storage stability.

Effects of tidal range on mooring systems of wave energy converters

Wave energy converters are currently proposed to be deployed near coastal area for the closeness to the infrastructure and for ease of maintenance in order to reduce operational costs. The motivation behind this work is the fact that the deployment depths during the highest and lowest tides will have a significant effect on the mooring system of WECs. In this paper, the issue will be investigated by numerical modelling (using ANSYS AQWA) for both catenary and taut moorings to examine the performance of the mooring system in varying tides. The case study being considered is the ¼- scale wave energy test site in Galway Bay off the west coast of Ireland where some marine renewable energy devices can be tested. In this test site, the tidal range is macro-tidal with a range of approximately 6 m which is a large value relative to the water depth. In the numerical analysis, ANSYS AQWA suite has been used to simulate moored devices under wave excitation at varying tidal ranges. Results show that the highest tide will give rise to larger forces. While at lower depths, slackening of the mooring occurs. Therefore, the mooring lines must be designed to accommodate both situations.

The effects of agglomeration economies on the productivity of manufacturing local units in Ireland

The purpose of this study is to examine the effects of agglomeration economies on the productivity of manufacturing local units in Ireland. Four types of agglomeration economies are considered in this study. These are internal economies of scale, localization economies, related variety and urbanization economies. This study makes a number of contributions to the literature. Firstly, this is the first study to conduct an investigation of the effects of agglomeration economies on the productivity of manufacturing local units operating in Ireland. Secondly, this study distinguishes between indigenous and foreign-owned local units which is important given the dual nature of the Irish economy (Krugman, 1997). Thirdly, in addition to considering the effects of agglomeration economies, this study examines the impact of spurious agglomeration on the productivity of foreign-owned local units. Using data from the Census of Industrial Local Units and a series of IV GMM estimators to control for endogeneity, the results of the analysis conducted in Chapter 6 reveal that there are differences in the effects of agglomeration economies on the productivity of indigenous and foreign-owned local units. In Chapter 7 the Census of Industrial Local Units is supplemented by additional data sources and more in-depth measures are generated to capture the features of each of the external agglomeration economies considered in this analysis. There is some evidence to suggest that the availability of local inputs has a negative and significant impact on productivity. The NACE based measures of related variety reveal that the availability of local inputs and knowledge spillovers for related sectors have a negative and significant impact on productivity. There is clear evidence to suggest that urbanization economies are important for increasing the productivity of indigenous local units. The findings reveal that a 1% increase in population density in the NUTS 3 region leads to an increase in the productivity of indigenous local units of approximately 0.07% to 0.08%. The results also reveal that there is a significant difference in the effects of agglomeration economies on the productivity of low-tech and medium/high-tech indigenous local units. The more in-depth measures of agglomeration economies used in Chapter 7 are also used in Chapter 8. A series of IV GMM regressions are estimated in order to identify the impact of agglomeration economies and spurious agglomeration on the productivity of foreign-owned local units operating in Ireland. There is some evidence found to suggest that the availability of a pool of skilled labour has a positive and significant on productivity of foreign-owned local units. There is also evidence to suggest that localization knowledge spillovers have a negative impact on the productivity of foreign-owned local units. There is strong evidence to suggest that the availability of local inputs has a negative impact on the productivity. The negative impact is not confined to the NACE 4-digit sector but also extends into related sectors as determined by Porter’s (2003) cluster classification. The cluster based skills measure of related variety has a positive and significant impact on the productivity of foreign-owned local units. Similar to Chapter 7, there is clear evidence to suggest that urbanization economies are important for increasing the productivity of foreign-owned local units. Both the summary measure and each of the more in-depth measures of agglomeration economies have a positive and significant impact on productivity. Spurious agglomeration has a positive and significant impact on the productivity of foreign-owned local units. The results indicate that the more foreign-owned local units of the same nationality in the country the greater the levels of productivity for the local unit. From a policy perspective, urbanization economies are clearly important for increasing the productivity of both indigenous and foreign-owned local units. Furthermore, the availability of a pool of skilled labour appears to be important for increasing the productivity of foreign-owned local units. Another policy implication that arises from these results relates to the differences observed between indigenous local units and foreign-owned local units and also between low-tech and medium/high-tech indigenous local units. These findings indicate that ‘one-size-fits-all’ type policies are not appropriate for increasing the productivity of local units operating in Ireland. Policies should be tailored to the needs of either indigenous or foreign-owned local units and also to specific sectors. This positive finding for own country spurious agglomeration is important from a policy perspective and is one that IDA Ireland should take on board.

Ultra high-pressure homogenized emulsions stabilized by sodium caseinate: effects of protein concentration and pressure on emulsions structure and stability

Microstructure, physical properties and oxidative stability of emulsions treated by colloid mill (CM), conventional homogenization (CH, 15 MPa) and ultra-high-pressure homogenization (UHPH, 100–300 MPa) by using different concentrations of 1, 3 and 5 g/100 g of sodium caseinate (SC), were evaluated. The application of UHPH treatment at 200 and 300 MPa resulted in emulsions that were highly stable to creaming and oxidation, especially when the protein content increased from 1 to 3 and 5 g/100 g. Further, increasing the protein content to 3 and 5 g/100 g in UHPH emulsions tended to change the rheological behavior from Newtonian to shear thinning. CH emulsions containing 1 g/100 g of protein exhibited Newtonian flow behavior with lower tendencies to creaming compared to those formulated with 3 or 5 g/100 g. This study has proved that UHPH processing at pressures (200–300 MPa) and in the presence of sufficient amount of sodium caseinate (5 g/100 g), produces emulsions with oil droplets in nano-/submicron scale with a narrow size distribution and high physical and oxidative stabilities, compared to CM and CH treatments.