Impact of non-optimal grounding of the CC2420 RFIC on a 802.15.4 Tyndall sensor wireless mote

The performance of an RF output matching network is dependent on integrity of the ground connection. If this connection is compromised in anyway, additional parasitic elements may occur that can degrade performance and yield unreliable results. Traditionally, designers measure Constant Wave (CW) power to determine that the RF chain is performing optimally, the device is properly matched and by implication grounded. It is shown that there are situations where modulation quality can be compromised due to poor grounding that is not apparent using CW power measurements alone. The consequence of this is reduced throughput, range and reliability. Measurements are presented on a Tyndall Mote using a CC2420 RFIC todemonstrate how poor solder contact between the ground contacts and the ground layer of the PCB can lead tothe degradation of modulated performance. Detailed evaluation that required the development of a new measurement definition for 802.15.4 and analysis is presented to show how waveform quality is affected while the modulated output power remains within acceptable limits.

Studies on Formica lugubris Zetterstedt in Ireland (Hymenoptera, Formicidae)

This thesis is based on studies of Formica lugubris from 1972-1975. While this species' range is diminishing in Ireland, the nests are quite common in the State plantations of South Tipperary. It is not certain that the species is indigenous. Above-ground activity occurs from late-February to the end of October; foraging begins in April. Two territorial "spring-battles" between neighbouring nests are described. Most active nests produced alatae of both sexes and flights were observed on successive June mornings above l7.5°C air temperature. Both polygyny and polycaly seem to be rare. Where the nests occur commonly, the recorded densities are similar to those reported from the continent. Most nests persisted at the same site since 1973. The nest-sites are described by recording an array of nest, soil, tree, vegetation and location variables at each site. Pinus sylvestris is the most important overhead tree. Nests seem to be the same age as their surrounding plantation and reach a maximum of c. 30 years. Nearest-neighbour analysis suggests the sites are overdispersed. Forager route-fidelity was studied and long-term absence from the route, anaesthetization and "removal" of an aphid tree had little effect on this fidelity. There were no identifiable groups of workers specifically honeydew or prey-carriers. Size-duty relationships of workers participating in adult transport are described. Foraging rhythms were studied on representative days: the numbers foraging were linearly related to temperature. Route-traffic passed randomly and an average foraging trip lasted c. four hours. Annual food intake to a nest with 25 000 foragers was estimated at approximately 75 kg honeydew and 2 million prey-items. Forager-numbers and colony-size were estimated using the capture-mark - recapture method: paint marking was used for the forager estimate and an interval radiophosphorus mark, detected by autoradiography, was used for the colony-size estimate. The aphids attended by lugubris and the nest myrmecophiles are recorded.

Monasticism and its limits: rematerialising monastic space in early medieval Ireland

This thesis creates a multi-faceted archaeological context for early Irish monasticism, so as to ‘rematerialise’ a phenomenon that has been neglected by recent archaeological scholarship. Following revision of earlier models of the early Irish Church, archaeologists are now faced with redefining monasticism and distinguishing it from other diverse forms of Christian lifestyle. This research addresses this challenge, exploring the ways in which material limits can be set on the monastic phenomenon. The evidence for early Irish monasticism does not always conform to modern expectations of its character, and monastic space must be examined as culturally unique in its own right - though this thesis demonstrates that early Irish monasticism was by no means as unorthodox in its contemporary European setting as has previously been suggested. The research is informed by theories of the body, habitus and space, drawing on a wide body of archaeological, religious, sociological and anthropological thought. The data-set comprises evidences gathered through field-survey, reassessment of archaeological scholarship, historical research and cartographic research, enabling consideration of the ways in which early Irish monastics engaged with their environments. A sample of thirty-one early Irish ecclesiastical sites plus Iona forms the basis for discussion of the location and layout of monastic space, the ways in which monastics used buildings and space in their daily lives, the relationship of monasticism and material culture, the setting of mental and physical limits on monastic space and monastic bodies, and the variety of monastic lifestyles that pertained in early medieval Ireland. The study then examines the Christian landscapes of two case-studies in mid-Western Ireland in order to illustrate how monasticism functioned on the ground in these areas. As this research shows, the material complexities of early Irish monastic life are capable of archaeological definition in terms of both communal and personal lived experience.

Fabrication, characterisation and electroanalysis at 1-dimensional nanostructures

Integrated nanowire electrodes that permit direct, sensitive and rapid electrochemical based detection of chemical and biological species are a powerful emerging class of sensor devices. As critical dimensions of the electrodes enter the nanoscale, radial analyte diffusion profiles to the electrode dominate with a corresponding enhancement in mass transport, steady-state sigmoidal voltammograms, low depletion of target molecules and faster analysis. To optimise these sensors it is necessary to fully understand the factors that influence performance limits including: electrode geometry, electrode dimensions, electrode separation distances (within nanowire arrays) and diffusional mass transport. Therefore, in this thesis, theoretical simulations of analyte diffusion occurring at a variety of electrode designs were undertaken using Comsol Multiphysics®. Sensor devices were fabricated and corresponding experiments were performed to challenge simulation results. Two approaches for the fabrication and integration of metal nanowire electrodes are presented: Template Electrodeposition and Electron-Beam Lithography. These approaches allow for the fabrication of nanowires which may be subsequently integrated at silicon chip substrates to form fully functional electrochemical devices. Simulated and experimental results were found to be in excellent agreement validating the simulation model. The electrochemical characteristics exhibited by nanowire electrodes fabricated by electronbeam lithography were directly compared against electrochemical performance of a commercial ultra-microdisc electrode. Steady-state cyclic voltammograms in ferrocenemonocarboxylic acid at single ultra-microdisc electrodes were observed at low to medium scan rates (≤ 500 mV.s-1). At nanowires, steady-state responses were observed at ultra-high scan rates (up to 50,000 mV.s-1), thus allowing for much faster analysis (20 ms). Approaches for elucidating faradaic signal without the requirement for background subtraction were also developed. Furthermore, diffusional process occurring at arrays with increasing inter-electrode distance and increasing number of nanowires were explored. Diffusion profiles existing at nanowire arrays were simulated with Comsol Multiphysics®. A range of scan rates were modelled, and experiments were undertaken at 5,000 mV.s-1 since this allows rapid data capture required for, e.g., biomedical, environmental and pharmaceutical diagnostic applications.

Voltage properties of optically injected long wavelength VCSELs: Theory and experiment

Future high speed communications networks will transmit data predominantly over optical fibres. As consumer and enterprise computing will remain the domain of electronics, the electro-optical conversion will get pushed further downstream towards the end user. Consequently, efficient tools are needed for this conversion and due to many potential advantages, including low cost and high output powers, long wavelength Vertical Cavity Surface Emitting Lasers (VCSELs) are a viable option. Drawbacks, such as broader linewidths than competing options, can be mitigated through the use of additional techniques such as Optical Injection Locking (OIL) which can require significant expertise and expensive equipment. This thesis addresses these issues by removing some of the experimental barriers to achieving performance increases via remote OIL. Firstly, numerical simulations of the phase and the photon and carrier numbers of an OIL semiconductor laser allowed the classification of the stable locking phase limits into three distinct groups. The frequency detuning of constant phase values (ø) was considered, in particular ø = 0 where the modulation response parameters were shown to be independent of the linewidth enhancement factor, α. A new method to estimate α and the coupling rate in a single experiment was formulated. Secondly, a novel technique to remotely determine the locked state of a VCSEL based on voltage variations of 2mV−30mV during detuned injection has been developed which can identify oscillatory and locked states. 2D & 3D maps of voltage, optical and electrical spectra illustrate corresponding behaviours. Finally, the use of directly modulated VCSELs as light sources for passive optical networks was investigated by successful transmission of data at 10 Gbit/s over 40km of single mode fibre (SMF) using cost effective electronic dispersion compensation to mitigate errors due to wavelength chirp. A widely tuneable MEMS-VCSEL was established as a good candidate for an externally modulated colourless source after a record error free transmission at 10 Gbit/s over 50km of SMF across a 30nm single mode tuning range. The ability to remotely set the emission wavelength using the novel methods developed in this thesis was demonstrated.