Location dependence of a MEMS electromagnetic transducer with respect to an AC power source

A MEMS, silicon based device with a cantilever oscillationsand an integrated magnet is presented for magnetic to electrical transduction. The cantilever structure can be configured either as an energy harvester to harvest power from an AC power line or as an AC current sensor. The positioning of the transducer with respect to the AC conductor is critical in both scenarios. For the energy scavenger, correct positioning is required to optimize the harvested power. For the current sensor, it is necessary to optimise the sensitivity of the sensor. This paper considers the effect of the relative position of the transducer with respect to the wire on the resulting electromagnetic forces and torques driving the device. It is shown here that the magnetic torque acting on a cantilever beam with an integrated magnet and in the vicinity of an alternating electromagnetic field is a very significant driver of the cantilever oscillations.

Resonant power conversion topologies for inductive charging of electrical vehicle batteries

This thesis is concerned with inductive charging of electric vehicle batteries. Rectified power form the 50/60 Hz utility feeds a dc-ac converter which delivers high-frequency ac power to the electric vehicle inductive coupling inlet. The inlet configuration has been defined by the Society of Automotive Engineers in Recommended Practice J-1773. This thesis studies converter topologies related to the series resonant converter. When coupled to the vehicle inlet, the frequency-controlled series-resonant converter results in a capacitively-filtered series-parallel LCLC (SP-LCLC) resonant converter topology with zero voltage switching and many other desirable features. A novel time-domain transformation analysis, termed Modal Analysis, is developed, using a state variable transformation, to analyze and characterize this multi-resonant fourth-orderconverter. Next, Fundamental Mode Approximation (FMA) Analysis, based on a voltage-source model of the load, and its novel extension, Rectifier-Compensated FMA (RCFMA) Analysis, are developed and applied to the SP-LCLC converter. The RCFMA Analysis is a simpler and more intuitive analysis than the Modal Analysis, and provides a relatively accurate closed-form solution for the converter behavior. Phase control of the SP-LCLC converter is investigated as a control option. FMA and RCFMA Analyses are used for detailed characterization. The analyses identify areas of operation, which are also validated experimentally, where it is advantageous to phase control the converter. A novel hybrid control scheme is proposed which integrates frequency and phase control and achieves reduced operating frequency range and improved partial-load efficiency. The phase-controlled SP-LCLC converter can also be configured with a parallel load and is an excellent option for the application. The resulting topology implements soft-switching over the entire load range and has high full-load and partial-load efficiencies. RCFMA Analysis is used to analyze and characterize the new converter topology, and good correlation is shown with experimental results. Finally, a novel single-stage power-factor-corrected ac-dc converter is introduced, which uses the current-source characteristic of the SP-LCLC topology to provide power factor correction over a wide output power range from zero to full load. This converter exhibits all the advantageous characteristics of its dc-dc counterpart, with a reduced parts count and cost. Simulation and experimental results verify the operation of the new converter.

Source apportionment of PM2.5 in Cork Harbour, Ireland using a combination of single particle mass spectrometry and quantitative semi-continuous measurements

An aerosol time-of-flight mass spectrometer (ATOFMS) was deployed for the measurement of the size resolved chemical composition of single particles at a site in Cork Harbour, Ireland for three weeks in August 2008. The ATOFMS was co-located with a suite of semi-continuous instrumentation for the measurement of particle number, elemental carbon (EC), organic carbon (OC), sulfate and particulate matter smaller than 2.5 μm in diameter (PM2.5). The temporality of the ambient ATOFMS particle classes was subsequently used in conjunction with the semi-continuous measurements to apportion PM2.5 mass using positive matrix factorisation. The synergy of the single particle classification procedure and positive matrix factorisation allowed for the identification of six factors, corresponding to vehicular traffic, marine, long-range transport, various combustion, domestic solid fuel combustion and shipping traffic with estimated contributions to the measured PM2.5 mass of 23%, 14%, 13%, 11%, 5% and 1.5% respectively. Shipping traffic was found to contribute 18% of the measured particle number (20–600 nm mobility diameter), and thus may have important implications for human health considering the size and composition of ship exhaust particles. The positive matrix factorisation procedure enabled a more refined interpretation of the single particle results by providing source contributions to PM2.5 mass, while the single particle data enabled the identification of additional factors not possible with typical semi-continuous measurements, including local shipping traffic.

Work, class and conflict: a comparative study of three Cork factories, incorporating oral testimony

This dissertation presents a comparative study of three factories in Cork Harbour area, Sunbeam Wolsey (1927-90), Irish Steel (1939-2001) and the Ford Marina Plant (1917-84). All three factories were significant industrial employers in both a domestic (Irish) and a local (Cork) context and are broadly representative of the Irish manufacturing industry that was developed under the policies of tariff protection introduced in the 1930s and gradually phased out between the late 1950s and the mid-1980s. Sunbeam Wolsey was a textile and clothing concern located on the north side of Cork City that possessed a borderline monopoly within its economic sector and was among the largest private employers of female labour in twentieth century Ireland. Irish Steel was the country’s only steel mill, located on Haulbowline island, a brief ferry-ride from the seaside town of Cobh, and was unusual in being one of the few manufacturing concerns operated as a nationalised industry under the auspices of the state. The Ford Marina plant predated the introduction of protectionism by more than a decade and began as the centre of the Ford empire’s tractor manufacturing business, before switching to the production of private motor vehicles for the Irish market in 1932. All three industries were closed or sold off when the state withdrew support, either in the form of tariff protection (Ford, Sunbeam) or direct funding (Irish Steel). While devoting much attention to the three firms, the central concern of this dissertation is not the companies themselves (though the economic history portion of the dissertation is substantial), but the workers they employed, examining the lives of these individuals both as members of the Irish working class, and, more specifically, as employees of the three factories under consideration. The project can be best described as a comparative factory study, comparing and contrasting the three workforces, focusing primarily on industrial relation and the experience of work. This dissertation utilises both documentary evidence and a significant quantity of oral testimony, breaking new ground by making the workplace the central focus of its investigation. The principal aims of the study are: 1. To document the lives of those who worked in these factories, capturing through oral testimony their subjective experiences of social class and factory life, as well as differences among narrators in terms of gender and status. In achieving this aim, the study will provide a broader social context for its detailed analysis of work and industrial relations in each firm. 2. To analyse the three workplaces and determine how and why each developed such distinct systems of industrial relations at the factory level, as well as to compare and contrast these systems. 3. To examine the nature of work in each factory and to determine how work and industrial relations in each firm developed over time, relating these changes both to internal and external factors. Additionally, the project will provide a comparative analysis of these changes.

The Aghadown bronze axes, Paddock Td., Co. Cork

A brief account of the two axes to be described and illustrated here was published by Power in 1926. He states that they were discovered at Aghadown near Baltimore, in a souterrain locally known as Poll-a-Talmhain