Structural carpentry in medieval Ireland: continuity and change

The study of medieval carpentry is probably one of the most neglected aspects of archaeological research in Ireland. The principal difficulty is the nature of the evidence, in that timber, unless the conditions are right, rarely leaves a trace above ground. The problem is further exacerbated by the fact that not a single medieval timber-framed building has survived in Ireland. Nevertheless, in recent years, in addition to the medieval roof of Dunsoghley, which up to quite recently was thought to be the only surviving roof structure in Ireland, a further eight medieval roof structures have been identified. Furthermore, an extensive corpus of early medieval mills, with evidence for advanced Roman carpentry techniques, has been excavated, while evidence for Viking houses, on what is probably the largest extant Viking settlement in Europe, have also been recovered. Although post and wattle structures dominate the archaeological record of the Viking period, nevertheless, it will be shown that the Roman tradition of carpentry, evidenced in the early medieval mills from the early seventh century, continued in use in the wider Gaelic community. And it is one of the pivotal points of this study, that with the takeover of Dublin by the Gaelic Irish in the late tenth century, this Roman carpentry tradition was gradually assimilated into the carpentry tradition of the Viking towns, which were now largely inhabited by a mixed population of Hiberno-Norse. Evidence for this Gaelic influence can be seen not only in the gradual replacement of the Viking post and wattle house by timber houses with load-bearing walls, but more importantly by the evidence for waterfront structures founded on baseplates with mortise and tenoned uprights on the pre-Norman waterfront in Cork. Furthermore, it will be shown, that the carpentry techniques used to build the Wood Quay revetments, shortly after the Anglo-Norman conquest in AD 1170, supports this contention.

The development of a computer model to optimize the performance of a 50kWp photovoltaic system

A computer model has been developed to optimize the performance of a 50kWp photovoltaic system which supplies electrical energy to a dairy farm at Fota Island in Cork Harbour. Optimization of the system involves maximising the efficiency and increasing the performance and reliability of each hardware unit. The model accepts horizontal insolation, ambient temperature, wind speed, wind direction and load demand as inputs. An optimization program uses the computer model to simulate the optimum operating conditions. From this analysis, criteria are established which are used to improve the photovoltaic system operation. This thesis describes the model concepts, the model implementation and the model verification procedures used during development. It also describes the techniques which are used during system optimization. The software, which is written in FORTRAN, is structured in modular units to provide logical and efficient programming. These modular units may also be used in the modelling and optimization of other photovoltaic systems.

The reliability mathematical model of load-sharing parallel systems based on fatigue cumulative damage

Conventional reliability models for parallel systems are not applicable for the analysis of parallel systems with load transfer and sharing. In this short communication, firstly, the dependent failures of parallel systems are analyzed, and the reliability model of load-sharing parallel system is presented based on Miner cumulative damage theory and the full probability formula. Secondly, the parallel system reliability is calculated by Monte Carlo simulation when the component life follows the Weibull distribution. The research result shows that the proposed reliability mathematical model could analyze and evaluate the reliability of parallel systems in the presence of load transfer.

System operational costs reduction with non-conventional reactive power sources

Wind energy installations are increasing in power systems worldwide and wind generation capacity tends to be located some distance from load centers. A conflict may arise at times of high wind generation when it becomes necessary to curtail wind energy in order to maintain conventional generators on-line for the provision of voltage control support at load centers. Using the island of Ireland as a case study and presenting commercially available reactive power support devices as possible solutions to the voltage control problems in urban areas, this paper explores the reduction in total generation costs resulting from the relaxation of the operational constraints requiring conventional generators to be kept on-line near load centers for reactive power support. The paper shows that by 2020 there will be possible savings of 87€m per annum and a reduction in wind curtailment of more than a percentage point if measures are taken to relax these constraints.

Novel efficient technologies in Europe for axle bearing condition monitoring – the MAXBE project

Axle bearing damage with possible catastrophic failures can cause severe disruptions or even dangerous derailments, potentially causing loss of human life and leading to significant costs for railway infrastructure managers and rolling stock operators. Consequently the axle bearing damage process has safety and economic implications on the exploitation of railways systems. Therefore it has been the object of intense attention by railway authorities as proved by the selection of this topic by the European Commission in calls for research proposals. The MAXBE Project (http://www.maxbeproject.eu/), an EU-funded project, appears in this context and its main goal is to develop and to demonstrate innovative and efficient technologies which can be used for the onboard and wayside condition monitoring of axle bearings. The MAXBE (interoperable monitoring, diagnosis and maintenance strategies for axle bearings) project focuses on detecting axle bearing failure modes at an early stage by combining new and existing monitoring techniques and on characterizing the axle bearing degradation process. The consortium for the MAXBE project comprises 18 partners from 8 member states, representing operators, railway administrations, axle bearing manufactures, key players in the railway community and experts in the field of monitoring, maintenance and rolling stock. The University of Porto is coordinating this research project that kicked-off in November 2012 and it is completed on October 2015. Both on-board and wayside systems are explored in the project since there is a need for defining the requirement for the onboard equipment and the range of working temperatures of the axle bearing for the wayside systems. The developed monitoring systems consider strain gauges, high frequency accelerometers, temperature sensors and acoustic emission. To get a robust technology to support the decision making of the responsible stakeholders synchronized measurements from onboard and wayside monitoring systems are integrated into a platform. Also extensive laboratory tests were performed to correlate the in situ measurements to the status of the axle bearing life. With the MAXBE project concept it will be possible: to contribute to detect at an early stage axle bearing failures; to create conditions for the operational and technical integration of axle bearing monitoring and maintenance in different European railway networks; to contribute to the standardization of the requirements for the axle bearing monitoring, diagnosis and maintenance. Demonstration of the developed condition monitoring systems was performed in Portugal in the Northern Railway Line with freight and passenger traffic with a maximum speed of 220 km/h, in Belgium in a tram line and in the UK. Still within the project, a tool for optimal maintenance scheduling and a smart diagnostic tool were developed. This paper presents a synthesis of the most relevant results attained in the project. The successful of the project and the developed solutions have positive impact on the reliability, availability, maintainability and safety of rolling stock and infrastructure with main focus on the axle bearing health.