Analysis of the failure of cracked biscuits

Cracks or checks in biscuits weaken the material and cause the product to break at low load levels that are perceived as injurious to product quality. In this work, the structural response of circular digestive biscuits, with diameter 72 mm and thickness 7.2 mm, simply supported around the circumference and loaded by a central concentrated force was investigated by experiment and theory. Tests were conducted to quantify the distribution in breakage strength for structurally sound biscuits, biscuits with natural checks and biscuits with a single known part-through crack. For sound biscuits the breakage force is Normally distributed with a mean of 12.5 N and standard deviation of 1.2 N. For biscuits with checks, the corresponding statistics are 9.6 N ± 2.62 N respectively. The presence of a crack weakens the biscuit and strength, as measured by breakage force falls almost linearly with crack length and crack depth. The orientation of the crack, whether radial or tangential, and its location (i.e. position of the crack mid-point on the biscuit surface) are also important. Deep, radial, cracks located close to the biscuit centre can reduce the strength by up to 50%. Two separate failure criteria were examined for sound and cracked biscuits respectively. The results from these tests were in good accord with theory. For a biscuit without defects, breakage occurred when maximum biscuit stress reached or exceeded the failure stress of 420 kPa. For a biscuit with cracks, breakage occurred as above or alternatively when its critical stress intensity factor of 18 kPam0.5 was reached.

Irish Times coverage of Irish relief and development nongovernmental organisations, legitimacy and accountability, 1994-2009: analysis and implications for the role of nongovernmental organisations

The overall aim of this study was to investigate the extent to which and ways in which Irish relief and development nongovernmental organisations (NGOs) were linked with the concepts of legitimacy and accountability in Irish Times newspaper coverage between 1994 and 2009. This research was based on a quantitative content analysis of 215 Irish Times articles and the results were analysed using statistical methods. Key findings of the research included that NGO accountability received significantly more coverage than NGO legitimacy, "principal-agent" approaches to NGO accountability received significantly more coverage than "stakeholder" approaches to NGO accountability, and questioning of NGOs based on either their accountability or legitimacy was very limited. It is suggested that these findings may indicate both a failure by Irish NGOs to promote "development literacy" and global solidarity among the Irish public, and a limited degree of "development literacy" and global solidarity among the Irish public.

Survival analysis of adult tuberculosis disease

Background: We conducted a survival analysis of all the confirmed cases of Adult Tuberculosis (TB) patients treated in Cork-City, Ireland. The aim of this study was to estimate Survival time (ST), including median time of survival and to assess the association and impact of covariates (TB risk factors) to event status and ST. The outcome of the survival analysis is reported in this paper. Methods: We used a retrospective cohort study research design to review data of 647 bacteriologically confirmed TB patients from the medical record of two teaching hospitals. Mean age 49 years (Range 18–112). We collected information on potential risk factors of all confirmed cases of TB treated between 2008–2012. For the survival analysis, the outcome of interest was ‘treatment failure’ or ‘death’ (whichever came first). A univariate descriptive statistics analysis was conducted using a non- parametric procedure, Kaplan -Meier (KM) method to estimate overall survival (OS), while the Cox proportional hazard model was used for the multivariate analysis to determine possible association of predictor variables and to obtain adjusted hazard ratio. P value was set at <0.05, log likelihood ratio test at >0.10. Data were analysed using SPSS version 15.0. Results: There was no significant difference in the survival curves of male and female patients. (Log rank statistic = 0.194, df = 1, p = 0.66) and among different age group (Log rank statistic = 1.337, df = 3, p = 0.72). The mean overall survival (OS) was 209 days (95%CI: 92–346) while the median was 51 days (95% CI: 35.7–66). The mean ST for women was 385 days (95%CI: 76.6–694) and for men was 69 days (95%CI: 48.8–88.5). Multivariate Cox regression showed that patient who had history of drug misuse had 2.2 times hazard than those who do not have drug misuse. Smokers and alcohol drinkers had hazard of 1.8 while patients born in country of high endemicity (BICHE) had hazard of 6.3 and HIV co-infection hazard was 1.2. Conclusion: There was no significant difference in survival curves of male and female and among age group. Women had a higher ST compared to men. But men had a higher hazard rate compared to women. Anti-TNF, immunosuppressive medication and diabetes were found to be associated with longer ST, while alcohol, smoking, RICHE, BICHE was associated with shorter ST.

A facilities maintenance management process based on degradation prediction using sensed data

Energy efficiency and user comfort have recently become priorities in the Facility Management (FM) sector. This has resulted in the use of innovative building components, such as thermal solar panels, heat pumps, etc., as they have potential to provide better performance, energy savings and increased user comfort. However, as the complexity of components increases, the requirement for maintenance management also increases. The standard routine for building maintenance is inspection which results in repairs or replacement when a fault is found. This routine leads to unnecessary inspections which have a cost with respect to downtime of a component and work hours. This research proposes an alternative routine: performing building maintenance at the point in time when the component is degrading and requires maintenance, thus reducing the frequency of unnecessary inspections. This thesis demonstrates that statistical techniques can be used as part of a maintenance management methodology to invoke maintenance before failure occurs. The proposed FM process is presented through a scenario utilising current Building Information Modelling (BIM) technology and innovative contractual and organisational models. This FM scenario supports a Degradation based Maintenance (DbM) scheduling methodology, implemented using two statistical techniques, Particle Filters (PFs) and Gaussian Processes (GPs). DbM consists of extracting and tracking a degradation metric for a component. Limits for the degradation metric are identified based on one of a number of proposed processes. These processes determine the limits based on the maturity of the historical information available. DbM is implemented for three case study components: a heat exchanger; a heat pump; and a set of bearings. The identified degradation points for each case study, from a PF, a GP and a hybrid (PF and GP combined) DbM implementation are assessed against known degradation points. The GP implementations are successful for all components. For the PF implementations, the results presented in this thesis find that the extracted metrics and limits identify degradation occurrences accurately for components which are in continuous operation. For components which have seasonal operational periods, the PF may wrongly identify degradation. The GP performs more robustly than the PF, but the PF, on average, results in fewer false positives. The hybrid implementations, which are a combination of GP and PF results, are successful for 2 of 3 case studies and are not affected by seasonal data. Overall, DbM is effectively applied for the three case study components. The accuracy of the implementations is dependant on the relationships modelled by the PF and GP, and on the type and quantity of data available. This novel maintenance process can improve equipment performance and reduce energy wastage from BSCs operation.

Experimental analysis of novel telecom source materials and devices

Incumbent telecommunication lasers emitting at 1.5 µm are fabricated on InP substrates and consist of multiple strained quantum well layers of the ternary alloy InGaAs, with barriers of InGaAsP or InGaAlAs. These lasers have been seen to exhibit very strong temperature dependence of the threshold current. This strong temperature dependence leads to a situation where external cooling equipment is required to stabilise the optical output power of these lasers. This results in a significant increase in the energy bill associated with telecommunications, as well as a large increase in equipment budgets. If the exponential growth trend of end user bandwidth demand associated with the internet continues, these inefficient lasers could see the telecommunications industry become the dominant consumer of world energy. For this reason there is strong interest in developing new, much more efficient telecommunication lasers. One avenue being investigated is the development of quantum dot lasers on InP. The confinement experienced in these low dimensional structures leads to a strong perturbation of the density of states at the band edge, and has been predicted to result in reduced temperature dependence of the threshold current in these devices. The growth of these structures is difficult due to the large lattice mismatch between InP and InAs; however, recently quantum dots elongated in one dimension, known as quantum dashes, have been demonstrated. Chapter 4 of this thesis provides an experimental analysis of one of these quantum dash lasers emitting at 1.5 µm along with a numerical investigation of threshold dynamics present in this device. Another avenue being explored to increase the efficiency of telecommunications lasers is bandstructure engineering of GaAs-based materials to emit at 1.5 µm. The cause of the strong temperature sensitivity in InP-based quantum well structures has been shown to be CHSH Auger recombination. Calculations have shown and experiments have verified that the addition of bismuth to GaAs strongly reduces the bandgap and increases the spin orbit splitting energy of the alloy GaAs1−xBix. This leads to a bandstructure condition at x = 10 % where not only is 1.5 µm emission achieved on GaAs-based material, but also the bandstructure of the material can naturally suppress the costly CHSH Auger recombination which plagues InP-based quantum-well-based material. It has been predicted that telecommunications lasers based on this material system should operate in the absence of external cooling equipment and offer electrical and optical benefits over the incumbent lasers. Chapters 5, 6, and 7 provide a first analysis of several aspects of this material system relevant to the development of high bismuth content telecommunication lasers.