Design of miniaturized wireless sensor mote and actuator for building monitoring and control

In this paper, a wireless sensor network mote hardware design and implementation are introduced for building deployment application. The core of the mote design is based on the 8 bit AVR microcontroller, Atmega1281 and 2.4 GHz wireless communication chip, CC2420. The module PCB fabrication is using the stackable technology providing powerful configuration capability. Three main layers of size 25 mm2 are structured to form the mote; these are RF, sensor and power layers. The sensors were selected carefully to meet both the building monitoring and design requirements. Beside the sensing capability, actuation and interfacing to external meters/sensors are provided to perform different management control and data recording tasks. Experiments show that the developed mote works effectively in giving stable data acquisition and owns good communication and power performance.

Modelling and control of a floating oscillating water column

A novel numerical model of a Bent Backwards Duct Buoy (BBDB) Oscillating Water Column (OWC) Wave Energy Converter was created based on existing isolated numerical models of the different energy conversion systems utilised by an OWC. The novel aspect of this numerical model is that it incorporates the interdependencies of the different power conversion systems rather than modelling each system individually. This was achieved by accounting for the dynamic aerodynamic damping caused by the changing turbine rotational velocity by recalculating the turbine damping for each simulation sample and applying it via a feedback loop. The accuracy of the model was validated using experimental data collected during the Components for Ocean Renewable Energy Systems (CORES) EU FP-7 project that was tested in Galway Bay, Ireland. During the verification process, it was discovered that the model could also be applied as a valuable tool when troubleshooting device performance. A new turbine was developed and added to a full scale model after being investigated using Computational Fluid Dynamics. The energy storage capacity of the impulse turbine was investigated by modelling the turbine with both high and low inertia and applying three turbine control theories to the turbine using the full scale model. A single Maximum Power Point Tracking algorithm was applied to the low-inertia turbine, while both a fixed and dynamic control algorithm was applied to the high-inertia turbine. These results suggest that the highinertia turbine could be used as a flywheel energy storage device that could help minimize output power variation despite the low operating speed of the impulse turbine. This research identified the importance of applying dynamic turbine damping to a BBDB OWC numerical model, revealed additional value of the model as a device troubleshooting tool, and found that an impulse turbine could be applied as an energy storage system.

Prevalence and control of Clostridium difficile in patients with cystic fibrosis

The aim of this thesis was to investigate the high prevalence of Clostridium difficile in patients with cystic fibrosis (CF), and to control its dissemination. To determine the carriage rate of C. difficile in CF patients, 60 patients were tested for C. difficile and its toxin. In total, 50% of patients were found to be asymptomatic carriers of C. difficile despite toxin being detected in 31.66% of patients. Ribotyping of the C. difficile isolates revealed 16 distinct ribotypes, including the hyper virulent RT078. All isolates were sensitive to both Vancomycin and Metronidazole. The effect of CF and its treatment on the gut microbiota of CF patients was assessed by 16s sequencing of the gut microbiota of 68 CF patients. When compared to a healthy control group, CF patient gut microbiota was found to be less diverse and had an increased Firmicutes to Bacteriodetes ratio. Interestingly, CF patients who were carriers of C. difficile had a less diverse gut microbiota than C. difficile negative CF patients. Multilocus sequence typing was found to be comparable to PCR-ribotyping for typing C. difficile isolates from high risk patient groups. The sequence type ST 26 is potentially associated with CF patients as all seven isolates were found in this group and this sequence type has been previously reported in CF patients in a geographically distinct study. The bacteriophage ФCD6356 was assessed as a targeted antimicrobial against C. difficile in an ex-vivo model of the human distal colon. Despite reducing viable C. difficile by 1.75 logs over 24 hours, this bacteriophage was not suitable due to its lysogenic nature. Following treatment, all surviving C. difficile were immune to reinfection due to prophage integration. However, the ФCD6356 encoded endolysin was capable of reducing viable C. difficile by 2.9 over 2 hours in vitro after being cloned and expressed in Escherichia coli.