Bottom-up modelling of energy demand and technical energy savings potential in the Irish residential sector

The International Energy Agency has repeatedly identified increased end-use energy efficiency as the quickest, least costly method of green house gas mitigation, most recently in the 2012 World Energy Outlook, and urges all governing bodies to increase efforts to promote energy efficiency policies and technologies. The residential sector is recognised as a major potential source of cost effective energy efficiency gains. Within the EU this relative importance can be seen from a review of the National Energy Efficiency Action Plans (NEEAP) submitted by member states, which in all cases place a large emphasis on the residential sector. This is particularly true for Ireland whose residential sector has historically had higher energy consumption and CO2 emissions than the EU average and whose first NEEAP targeted 44% of the energy savings to be achieved in 2020 from this sector. This thesis develops a bottom-up engineering archetype modelling approach to analyse the Irish residential sector and to estimate the technical energy savings potential of a number of policy measures. First, a model of space and water heating energy demand for new dwellings is built and used to estimate the technical energy savings potential due to the introduction of the 2008 and 2010 changes to part L of the building regulations governing energy efficiency in new dwellings. Next, the author makes use of a valuable new dataset of Building Energy Rating (BER) survey results to first characterise the highly heterogeneous stock of existing dwellings, and then to estimate the technical energy savings potential of an ambitious national retrofit programme targeting up to 1 million residential dwellings. This thesis also presents work carried out by the author as part of a collaboration to produce a bottom-up, multi-sector LEAP model for Ireland. Overall this work highlights the challenges faced in successfully implementing both sets of policy measures. It points to the wide potential range of final savings possible from particular policy measures and the resulting high degree of uncertainty as to whether particular targets will be met and identifies the key factors on which the success of these policies will depend. It makes recommendations on further modelling work and on the improvements necessary in the data available to researchers and policy makers alike in order to develop increasingly sophisticated residential energy demand models and better inform policy.

Characterising novel anti-biofilm targets for the treatment of chronic Pseudomonas aeruginosa infection in the cystic fibrosis lung

The global rise in antibiotic resistance is a significant problem facing healthcare professionals. In particular within the cystic fibrosis (CF) lung, bacteria can establish chronic infection and resistance to a wide array of antibiotic therapies. One of the principle pathogens associated with chronic infection in the CF lung is Pseudomonas aeruginosa. P. aeruginosa can establish chronic infection in the CF lung partly through the use of the biofilm mode of growth. This biofilm mode of growth offers a considerable degree of protection from a wide variety of challenges such as the host immune system or antibiotic therapy. The threat posed by the emergence of chronic pathogens is prompting the development of next generation antimicrobials. The biofilm mode of growth is often central to the establishment of chronic infection and the development of antibiotic resistance. Thus, targeting biofilm formation has emerged as one of the principle strategies for the development of next generation antimicrobials. In this thesis two separate approaches were used to identify potential anti - biofilm targets. The first strategy focused on the identification of novel genes with a role in a biofilm formation. High throughput screening identified almost 300 genes which had a role in biofilm formation. A number of these genes were characterised at a phenotypic and a molecular level. The second strategy focused on the identification of compounds capable of inhibiting biofilm formation. A collection of marine sponge isolated bacteria were screened for the ability to inhibit the central pathway regulating biofilm formation, quorum sensing. A number of distinct isolates were identified that had quorum sensing inhibition activity from which, a Pseudomonas isolate was selected for further characterisation. A specific compound capable of inhibiting quorum sensing was identified using chemical analytical technologies in the supernatant of this marine isolate.

Uncertainty visualization in 3D scalar data

One problem in most three-dimensional (3D) scalar data visualization techniques is that they often overlook to depict uncertainty that comes with the 3D scalar data and thus fail to faithfully present the 3D scalar data and have risks which may mislead users’ interpretations, conclusions or even decisions. Therefore this thesis focuses on the study of uncertainty visualization in 3D scalar data and we seek to create better uncertainty visualization techniques, as well as to find out the advantages/disadvantages of those state-of-the-art uncertainty visualization techniques. To do this, we address three specific hypotheses: (1) the proposed Texture uncertainty visualization technique enables users to better identify scalar/error data, and provides reduced visual overload and more appropriate brightness than four state-of-the-art uncertainty visualization techniques, as demonstrated using a perceptual effectiveness user study. (2) The proposed Linked Views and Interactive Specification (LVIS) uncertainty visualization technique enables users to better search max/min scalar and error data than four state-of-the-art uncertainty visualization techniques, as demonstrated using a perceptual effectiveness user study. (3) The proposed Probabilistic Query uncertainty visualization technique, in comparison to traditional Direct Volume Rendering (DVR) methods, enables radiologists/physicians to better identify possible alternative renderings relevant to a diagnosis and the classification probabilities associated to the materials appeared on these renderings; this leads to improved decision support for diagnosis, as demonstrated in the domain of medical imaging. For each hypothesis, we test it by following/implementing a unified framework that consists of three main steps: the first main step is uncertainty data modeling, which clearly defines and generates certainty types of uncertainty associated to given 3D scalar data. The second main step is uncertainty visualization, which transforms the 3D scalar data and their associated uncertainty generated from the first main step into two-dimensional (2D) images for insight, interpretation or communication. The third main step is evaluation, which transforms the 2D images generated from the second main step into quantitative scores according to specific user tasks, and statistically analyzes the scores. As a result, the quality of each uncertainty visualization technique is determined.

Elicitation techniques for the evaluation of speech under stress: Towards a framework for use in a controlled environment

Existing work in Computer Science and Electronic Engineering demonstrates that Digital Signal Processing techniques can effectively identify the presence of stress in the speech signal. These techniques use datasets containing real or actual stress samples i.e. real-life stress such as 911 calls and so on. Studies that use simulated or laboratory-induced stress have been less successful and inconsistent. Pervasive, ubiquitous computing is increasingly moving towards voice-activated and voice-controlled systems and devices. Speech recognition and speaker identification algorithms will have to improve and take emotional speech into account. Modelling the influence of stress on speech and voice is of interest to researchers from many different disciplines including security, telecommunications, psychology, speech science, forensics and Human Computer Interaction (HCI). The aim of this work is to assess the impact of moderate stress on the speech signal. In order to do this, a dataset of laboratory-induced stress is required. While attempting to build this dataset it became apparent that reliably inducing measurable stress in a controlled environment, when speech is a requirement, is a challenging task. This work focuses on the use of a variety of stressors to elicit a stress response during tasks that involve speech content. Biosignal analysis (commercial Brain Computer Interfaces, eye tracking and skin resistance) is used to verify and quantify the stress response, if any. This thesis explains the basis of the author’s hypotheses on the elicitation of affectively-toned speech and presents the results of several studies carried out throughout the PhD research period. These results show that the elicitation of stress, particularly the induction of affectively-toned speech, is not a simple matter and that many modulating factors influence the stress response process. A model is proposed to reflect the author’s hypothesis on the emotional response pathways relating to the elicitation of stress with a required speech content. Finally the author provides guidelines and recommendations for future research on speech under stress. Further research paths are identified and a roadmap for future research in this area is defined.

Characterisation of the role of canonical BMP-Smad 1/5/8 signalling in the development of ventral midbrain dopaminergic neurons

Ventral midbrain (VM) dopaminergic (DA) neurons, which project to the dorsal striatum via the nigrostriatal pathway, are progressively degenerated in Parkinson’s disease (PD). The identification of the instructive factors that regulate midbrain DA neuron development, and the subsequent elucidation of the molecular bases of their effects, is vital. Such an understanding would facilitate the generation of transplantable DA neurons from stem cells and the identification of developmentally-relevant neurotrophic factors, the two most promising therapeutic approaches for PD. Two related members of the bone morphogenetic protein (BMP) family, BMP2 and growth/differentiation factor (GDF) 5, which signal via a canonical Smad 1/5/8 signalling pathway, have been shown to have neurotrophic effects on midbrain DA neurons both in vitro and in vivo, and may function to regulate VM DA neuronal development. However, the molecular (signalling pathway(s)) and cellular (direct neuronal or indirect via glial cells) mechanisms of their effects remain to be elucidated. The present thesis hypothesised that canonical Smad signalling mediates the direct effects of BMP2 and GDF5 on the development of VM DA neurons. By activating, modulating and/or inhibiting various components of the BMP-Smad signalling pathway, this research demonstrated that GDF5- and BMP2-induced neurite outgrowth from midbrain DA neurons is dependent on BMP type I receptor activation of the Smad signalling pathway. The role of glial cell-line derived neurotrophic factor (GDNF)-signalling, dynamin-dependent endocytosis and Smad interacting protein-1 (Sip1) regulation, in the neurotrophic effects of BMP2 and GDF5 were determined. Finally, the in vitro development of VM neural stem cells (NSCs) was characterised, and the ability of GDF5 and BMP2 to induce these VM NSCs towards DA neuronal differentiation was investigated. Taken together, these experiments identify GDF5 and BMP2 as novel regulators of midbrain DA neuronal induction and differentiation, and demonstrate that their effects on DA neurons are mediated by canonical BMPR-Smad signalling.

Atomic layer deposition of copper for CMOS interconnects

This work concerns the atomic layer deposition (ALD) of copper. ALD is a technique that allows conformal coating of difficult topographies such as narrow trenches and holes or even shadowed regions. However, the deposition of pure metals has so far been less successful than the deposition of oxides except for a few exceptions. Challenges include difficulties associated with the reduction of the metal centre of the precursor at reasonable temperatures and the tendency of metals to agglomerate during the growth process. Cu is a metal of special technical interest as it is widely used for interconnects on CMOS devices. These interconnects are usually fabricated by electroplating, which requires the deposition of thin Cu seed layers onto the trenches and vias. Here, ALD is regarded as potential candidate for replacing the current PVD technique, which is expected to reach its limitations as the critical dimensions continue to shrink. This work is separated into two parts. In the first part, a laboratory-scale ALD reactor was constructed and used for the thermal ALD of Cu. In the second part, the potentials of the application of Cu ALD on industry scale fabrication were examined in a joint project with Applied Materials and Intel. Within this project precursors developed by industrial partners were evaluated on a 300 mm Applied Materials metal-ALD chamber modified with a direct RF-plasma source. A feature that makes ALD a popular technique among researchers is the possibility to produce high- level thin film coatings for micro-electronics and nano-technology with relatively simple laboratory- scale reactors. The advanced materials and surfaces group (AMSG) at Tyndall National Institute operates a range of home-built ALD reactors. In order to carry out Cu ALD experiments, modifications to the normal reactor design had to be made. For example a carrier gas mechanism was necessary to facilitate the transport of the low-volatile Cu precursors. Precursors evaluated included the readily available Cu(II)-diketonates Cu-bis(acetylacetonate), Cu-bis(2,2,6,6-tetramethyl-hepta-3,5-dionate) and Cu-bis(1,1,1,5,5,5-hexafluoacetylacetonate) as well as the Cu-ketoiminate Cu-bis(4N-ethylamino- pent-3-en-2-onate), which is also known under the trade name AbaCus (Air Liquide), and the Cu(I)- silylamide 1,3-diisopropyl-imidazolin-2-ylidene Cu(I) hexamethyldisilazide ([NHC]Cu(hmds)), which was developed at Carleton University Ottawa. Forming gas (10 % H2 in Ar) was used as reducing agent except in early experiments where formalin was used. With all precursors an extreme surface selectivity of the deposition process was observed and significant growth was only achieved on platinum-group metals. Improvements in the Cu deposition process were obtained with [NHC]Cu(hmds) compared with the Cu(II) complexes. A possible reason is the reduced oxidation state of the metal centre. Continuous Cu films were obtained on Pd and indications for saturated growth with a rate of about 0.4 Å/cycle were found for deposition at 220 °C. Deposits obtained on Ru consisted of separated islands. Although no continuous films could be obtained in this work the relatively high density of Cu islands obtained was a clear improvement as compared to the deposits grown with Cu(II) complexes. When ultra-thin Pd films were used as substrates, island growth was also observed. A likely reason for this extreme difference to the Cu films obtained on thicker Pd films is the lack of stress compensation within the thin films. The most likely source of stress compensation in the thicker Pd films is the formation of a graded interlayer between Pd and Cu by inter-diffusion. To obtain continuous Cu films on more materials, reduction of the growth temperature was required. This was achieved in the plasma assisted ALD experiments discussed in the second part of this work. The precursors evaluated included the AbaCus compound and CTA-1, an aliphatic Cu-bis(aminoalkoxide), which was supplied by Adeka Corp.. Depositions could be carried out at very low temperatures (60 °C Abacus, 30 °C CTA-1). Metallic Cu could be obtained on all substrate materials investigated, but the shape of the deposits varied significantly between the substrate materials. On most materials (Si, TaN, Al2O3, CDO) Cu grew in isolated nearly spherical islands even at temperatures as low as 30 °C. It was observed that the reason for the island formation is the coalescence of the initial islands to larger, spherical islands instead of forming a continuous film. On the other hand, the formation of nearly two-dimensional islands was observed on Ru. These islands grew together forming a conductive film after a reasonably small number of cycles. The resulting Cu films were of excellent crystal quality and had good electrical properties; e.g. a resistivity of 2.39 µΩ cm was measured for a 47 nm thick film. Moreover, conformal coating of narrow trenches (1 µm deep 100/1 aspect ratio) was demonstrated showing the feasibility of the ALD process.

The development of a model of continuing professional development for teachers of primary science

A new science curriculum was introduced to primary schools in the Republic of Ireland in 2003. This curriculum, broader in scope than its 1971 predecessor (Curaclam na Bunscoile, 1971), requires teachers at all levels of primary school to teach science. A review carried out in 2008 of children’s experiences of this curriculum found that its implementation throughout the country was uneven. This finding, together with the increasing numbers of teachers who were requesting support to implement this curriculum, suggested the need for a review of Irish primary teachers’ needs in the area of science. The research study described in this thesis was undertaken to establish the extent of Irish primary teachers’ needs in the area of science by conducting a national survey. The data from this survey, together with data from international studies, were used to develop a theoretical framework for a model of Continuing Professional Development (CPD). This theoretical framework was used to design the Whole- School, In-School (WSIS) CPD model which was trialled in two case-study schools. The participants in these ‘action-research’ case-studies acted as co-researchers, who contributed to the development and evolution of the CPD model in each school. Analysis of the data gathered as part of the evaluation of the Whole-School, In- School (WSIS) model of CPD found an improved experience of science for children and improved confidence for teachers teaching at all levels of the primary school. In addition, a template for the establishment of a culture of collaborative CPD in schools has been developed from an analysis of the data

Investigation of lactic acid bacteria mediated bioprotection with applications in cereal industry. Case-study: malting process

Antifungal compounds produced by Lactic acid bacteria (LAB) metabolites can be natural and reliable alternative for reducing fungal infections pre- and post-harvest with a multitude of additional advantages for cereal-base products. Toxigenic and spoilage fungi are responsible for numerous diseases and economic losses. This thesis includes an overview of the impact fungi have on aspects of the cereal food chain. The applicability of LAB in plant protection and cereal industry is discussed in detail. Specific case studies include Fusarium head blight, and the impact of fungi in the malting and baking industry. The impact of Fusarium culmorum infected raw barley on the final malt quality was part of the investigation. In vitro infected barley grains were fully characterized. The study showed that the germinative energy of infected barley grains decreased by 45% and grains accumulated 199 μg.kg-1 of deoxynivalenol (DON). Barley grains were subsequently malted and fully characterized. Fungal biomass increased during all stages of malting. Infected malt accumulated 8-times its DON concentration during malting. Infected malt grains revealed extreme structural changes due to proteolytic, (hemi)-cellulolytic and starch degrading activity of the fungi, this led to increased friability and fragmentation. Infected grains also had higher protease and β-glucanase activities, lower amylase activity, a greater proportion of free amino and soluble nitrogen, and a lower β-glucan content. Malt loss was over 27% higher in infected malt when compared to the control. The protein compositional changes and respective enzymatic activity of infected barley and respective malt were characterized using a wide range of methods. F. culmorum infected barley grains showed an increase in proteolytic activity and protein extractability. Several metabolic proteins decreased and increased at different rates during infection and malting, showing a complex F. culmorum infection interdependence. In vitro F. culmorum infected malt was used to produce lager beer to investigate changes caused by the fungi during the brewing processes and their effect on beer quality attributes. It was found, that the wort containing infected malt had a lower pH, a higher FAN, higher β-glucan and a 45% increase in the purging rate, and led to premature yeast flocculation. The beer produced with infected malt (IB) had also a significantly different amino acid profile. IB flavour characterization revealed a higher concentration of esters, fusel alcohols, fatty acids, ketones, and dimethylsulfide, and in particular, acetaldehyde, when compared to the control. IB had a greater proportion of Strecker aldehydes and Maillard products contributing to an increased beer staling character. IB resulted in a 67% darker colour with a trend to better foam stability. It was also found that 78% of the accumulated mycotoxin deoxynivalenol in the malt was transferred into beer. A LAB cell-freesupernatant (cfs), produced in wort-base substrate, was investigated for its ability to inhibit Fusarium growth during malting. Wort was a suitable substrate for LAB exhibiting antifungal activity. Lactobacillus amylovorus DSM19280 inhibited 104 spores.mL-1 for 7 days, after 120 h of fermentation, while Lactobacillus reuteri R29 inhibited 105 spores.mL-1 for 7 days, after 48 h of fermentation. Both LAB cfs had significant different organic acid profiles. Acid-base antifungal compounds were identified and, phenyllactic, hydroxy-phenyllactic, and benzoic acids were present in higher concentrations when compared to the control. A 3 °P wort substrate inoculated With L. reuteri R29 (cfs) was applied in malting and successfully inhibited Fusarium growth by 23%, and mycotoxin DON by 80%. Malt attributes resulted in highly modified grains, lower pH, higher colouration, and higher extract yield. The implementation of selected LAB producing antifungal compounds can be used successfully in the malting process to reduce mould growth and mycotoxin production.

Helicobacter pylori: comparative genomics and structure-function analysis of the flagellum biogenesis protein HP0958

Helicobacter pylori is a gastric pathogen which infects ~50% of the global population and can lead to the development of gastritis, gastric and duodenal ulcers and carcinoma. Genome sequencing of H. pylori revealed high levels of genetic variability; this pathogen is known for its adaptability due to mechanisms including phase variation, recombination and horizontal gene transfer. Motility is essential for efficient colonisation by H. pylori. The flagellum is a complex nanomachine which has been studied in detail in E. coli and Salmonella. In H. pylori, key differences have been identified in the regulation of flagellum biogenesis, warranting further investigation. In this study, the genomes of two H. pylori strains (CCUG 17874 and P79) were sequenced and published as draft genome sequences. Comparative studies identified the potential role of restriction modification systems and the comB locus in transformation efficiency differences between these strains. Core genome analysis of 43 H. pylori strains including 17874 and P79 defined a more refined core genome for the species than previously published. Comparative analysis of the genome sequences of strains isolated from individuals suffering from H. pylori related diseases resulted in the identification of “disease-specific” genes. Structure-function analysis of the essential motility protein HP0958 was performed to elucidate its role during flagellum assembly in H. pylori. The previously reported HP0958-FliH interaction could not be substantiated in this study and appears to be a false positive. Site-directed mutagenesis confirmed that the coiled-coil domain of HP0958 is involved in the interaction with RpoN (74-284), while the Zn-finger domain is required for direct interaction with the full length flaA mRNA transcript. Complementation of a non-motile hp0958-null derivative strain of P79 with site-directed mutant alleles of hp0958 resulted in cells producing flagellar-type extrusions from non-polar positions. Thus, HP0958 may have a novel function in spatial localisation of flagella in H. pylori

Landscapes of kingship in early medieval Ireland, AD 400–1150

This thesis explores the evolution of kingship in early medieval Ireland (AD 400–1150) through a kingdom based and multi-scalar approach to royal landscapes. Through exploring the role of place and landscape in the construction of early medieval Irish kingship, this study will assess the relationship between the social, economic and ideological roles of the king in Irish society. Kingship in Ireland was vested in places, such that royal landscapes were the pre-eminent symbol of regality and authority. As such, an interdisciplinary study of kingship grounded in archaeological methodologies has a unique potential to contribute to our knowledge of the practice of kingship. Consequently, this research considers the material apparatus of different scales of kingships and explores the role of landscape in the construction of kingship and the evolution of kingdoms. It takes two major case studies; (i) Cashel, Munster and the Éoganachta federation; and (ii) the Uí Néill, Tara and the Síl nÁedo Sláine kingdom of Brega. Through interdisciplinary methodologies it charts the genesis and development of political federations, focusing specifically on the role that royal landscapes’ played in their evolution. Similarly, this thesis engages critically with the nature of assembly places and practices in Ireland, and focuses specifically on issues pertaining to the nature of assembly and the archaeological manifestation of such practices. It includes a list of 115 landscapes identified as assembly places, and through the analysis of this material, this thesis examines the ways in which different types of royal sites articulated together to create royal landscapes implicated in the exercise of kingship, and the construction and maintenance of authority. Moreover, through the analysis of assembly places within the context of the development of kingdoms, and structures of jurisdiction and administration, it also investigates the evolution of supra-regional scales of identity and community associated with the emergence of major political federations in early medieval Ireland.

Between respectability and disgrace: schismogenesis and the regeneration of inequality, stigma and social exclusion in Limerick

The thesis examines cultural processes underpinning the emergence, institutionalisation and reproduction of class boundaries in Limerick city. The research aims to bring a new understanding to the contemporary context of the city’s urban regeneration programme. Acknowledging and recognising other contemporary studies of division and exclusion, the thesis creates a distinctive approach which focuses on uncovering the cultural roots of inequality, educational disadvantage, stigma and social exclusion and the dynamics of their social reproduction. Using Bateson’s concept of schismogenesis (1953), the thesis looks to the persistent, but fragmented culture of community and develops a heuristic ‘symbolic order of the city’. This is defined as “…a cultural structure, the meaning making aspect of hierarchy, the categorical structures of world understanding, the way Limerick people understand themselves, their local and larger world” (p. 37). This provides a very different departure point for exploring the basis for urban regeneration in Limerick (and everywhere). The central argument is that if we want to understand the present (multiple) crises in Limerick we need to understand the historical, anthropological and recursive processes underpinning ‘generalised patterns of rivalry and conflict’. In addition to exploring the historical roots of status and stigma in Limerick, the thesis explores the mythopoesis of persistent, recurrent narratives and labels that mark the boundaries of the city’s identities. The thesis examines the cultural and social function of ‘slagging’ as a vernacular and highly particularised form of ironic, ritualised and, often, ‘cruel’ medium of communication (often exclusion). This is combined with an etymology of the vocabulary of Limerick slang and its mythological base. By tracing the origins of many normalised patterns of Limerick speech ‘sayings’, which have long since forgotten their roots, the thesis demonstrates how they perform a significant contemporary function in maintaining and reinforcing symbolic mechanisms of inclusion/exclusion. The thesis combines historical and archival data with biographical interviews, ethnographic data married to a deep historical hermeneutic analysis of this political community.

An investigation into mechanisms of visceral pain in rodents

Visceral pain is a debilitating symptom of irritable bowel syndrome (IBS), a disorder affecting up to 30% of adults. A better understanding of the mechanisms underlying visceral hypersensitivity may facilitate development of more targeted therapies, improving the quality of life of these individuals. The studies performed in this thesis were designed to investigate important factors of visceral pain, including early-life manipulations, genetic predisposition and sex hormones. Maternal separation (MS) consistently reproduces visceral hypersensitivity and altered anxiety-like behaviours in rats, symptoms associated with IBS. It has been found that 5-HT2B receptor antagonism blocks visceral pain but no difference in relative 5-HT2B receptor mRNA expression was found in hippocampus, amygdala and colon. The neuronal activation patterns of prefrontal cortex and amygdala of MS rats were then investigated. MS animals are characterised by differential activation of the prefrontal cortex (anterior cingulate cortex (ACC), infralibic cortex, prelimbic cortex) as well as the central nucleus of the amygdala (CeA). Genetic factors also contribute to pain syndromes such as IBS. We utilised the Wistar Kyoto (WKY) rat, a stress-sensitive strain, as an animal model of brain-gut axis dysfunction. WKY rats have a lower expression of the glutamate transporter EAAT2 and mGlu4 receptor in the ACC. Another early-life factor that can increase susceptibility to functional gastrointestinal symptoms later life is disruption of the gut microbiota, thus early-life antibiotic treatment was used to assess this effect. Antibiotic treatment induced visceral hypersensitivity in adulthood and may be related to observed reductions in spinal cord alpha-2A adrenoreceptor (adra2A) mRNA. Lastly, we investigated sex differences in visceral sensitivity. EAAT1 & 2 mRNA levels are lower in females, potentially increasing glutamatergic concentration at the symaptic level. Moreover, NR1 and NR2B subunits mRNA of NMDA receptor were increased in caudal ACC of females. These findings may account for sex differences in visceral sensitivity.

A study of the regulation of Trib family members expression in normal and malignant haematopoiesis

The Tribbles family of genes consist of three members; TRIB1, TRIB2 and TRIB3. Trib1 and Trib2 have been identified as oncogenes that can induce AML in mice. However little is known about how the expressions of the Tribbles family genes are controlled in the cell during haematopoiesis or leukaemogenesis. To investigate the Tribbles genes in leukaemia a bioinformatics approach was used. TRIB2 expression was found to be elevated in T-ALL and ALL with t(1;19). TRIB1 was found not to be significantly elevated in any leukaemic subtypes. Analyses of the TRIB1 and TRIB2 gene signatures in both leukaemic and normal haematopoietic cells identified pathways and transcription factors associated with these signatures. Pathways enriched for the TRIB1 signature included TLR signalling pathways and NF-κB pathways. Transcription factors enriched for this signature include C/EBP and SRF. Enriched for the TRIB2 signature includes T cell signalling pathways and Notch signalling pathways. Transcription factors enriched for this signature include E2F and ETS. Further investigation in vitro confirmed the finding that E2F1 was as a potential regulator of TRIB2 expression. E2F1 is able to directly bind to the TRIB2 promoter region and induce TRIB2 expression. C/EBPα p42 was found to inhibit E2F1 and the p30 isoform was found to cooperate with E2F1 induced activation of the TRIB2 promoter. Indicating the potential presence of a regulatory loop involved in the regulation of the TRIB2 gene. In conclusion we have investigated the Tribbles gene signatures in both normal haematopoietic and leukaemic cells. This has led to the identification of a number of pathways and transcription factors associated with these genes. We have also identified a family of transcription factors directly responsible for the regulation of TRIB2 expression. This regulatory pathway has the potential to be targeted in the treatment of leukaemia with a high TRIB2 signature.

Electrical machine characterisation and analysis for renewable energy applications

There has been an increased use of the Doubly-Fed Induction Machine (DFIM) in ac drive applications in recent times, particularly in the field of renewable energy systems and other high power variable-speed drives. The DFIM is widely regarded as the optimal generation system for both onshore and offshore wind turbines and has also been considered in wave power applications. Wind power generation is the most mature renewable technology. However, wave energy has attracted a large interest recently as the potential for power extraction is very significant. Various wave energy converter (WEC) technologies currently exist with the oscillating water column (OWC) type converter being one of the most advanced. There are fundemental differences in the power profile of the pneumatic power supplied by the OWC WEC and that of a wind turbine and this causes significant challenges in the selection and rating of electrical generators for the OWC devises. The thesis initially aims to provide an accurate per-phase equivalent circuit model of the DFIM by investigating various characterisation testing procedures. Novel testing methodologies based on the series-coupling tests is employed and is found to provide a more accurate representation of the DFIM than the standard IEEE testing methods because the series-coupling tests provide a direct method of determining the equivalent-circuit resistances and inductances of the machine. A second novel method known as the extended short-circuit test is also presented and investigated as an alternative characterisation method. Experimental results on a 1.1 kW DFIM and a 30 kW DFIM utilising the various characterisation procedures are presented in the thesis. The various test methods are analysed and validated through comparison of model predictions and torque-versus-speed curves for each induction machine. Sensitivity analysis is also used as a means of quantifying the effect of experimental error on the results taken from each of the testing procedures and is used to determine the suitability of the test procedures for characterising each of the devices. The series-coupling differential test is demonstrated to be the optimum test. The research then focuses on the OWC WEC and the modelling of this device. A software model is implemented based on data obtained from a scaled prototype device situated at the Irish test site. Test data from the electrical system of the device is analysed and this data is used to develop a performance curve for the air turbine utilised in the WEC. This performance curve was applied in a software model to represent the turbine in the electro-mechanical system and the software results are validated by the measured electrical output data from the prototype test device. Finally, once both the DFIM and OWC WEC power take-off system have been modeled succesfully, an investigation of the application of the DFIM to the OWC WEC model is carried out to determine the electrical machine rating required for the pulsating power derived from OWC WEC device. Thermal analysis of a 30 kW induction machine is carried out using a first-order thermal model. The simulations quantify the limits of operation of the machine and enable thedevelopment of rating requirements for the electrical generation system of the OWC WEC. The thesis can be considered to have three sections. The first section of the thesis contains Chapters 2 and 3 and focuses on the accurate characterisation of the doubly-fed induction machine using various testing procedures. The second section, containing Chapter 4, concentrates on the modelling of the OWC WEC power-takeoff with particular focus on the Wells turbine. Validation of this model is carried out through comparision of simulations and experimental measurements. The third section of the thesis utilises the OWC WEC model from Chapter 4 with a 30 kW induction machine model to determine the optimum device rating for the specified machine. Simulations are carried out to perform thermal analysis of the machine to give a general insight into electrical machine rating for an OWC WEC device.

Challengers to provisional republicanism: the official republican movement, people’s democracy and the Irish republican socialist party, 1968–98

The Provisional IRA and its political wing Sinn Féin have attracted by far the greatest scholarly interest of all the players in the Northern Irish conflict. This emphasis is perfectly legitimate, given the centrality of the Provos to so many turning-points in the conflict, from the collapse of Stormont in the early 1970s to the hunger strikes of the following decade and the ceasefires which were followed by the Belfast Agreement. My project, however, looks at political groups that at one time or another challenged the Provos for leadership of the militant, anti-state constituency in Northern Ireland (chiefly based in the Catholic working class). Although never as large or influential as the Provisional republicans, groups such as the Official IRA and the Irish Republican Socialist Party sometimes had a discernible impact on the course of events which is overlooked by most studies, and often pioneered ideas and tactics that were later adopted by the Provos themselves. The idea that republicans should embrace political action and work in broad campaigning alliances was promoted by the IRSP and socialist groups such as People’s Democracy before it was taken up by Gerry Adams and his allies, while the Official IRA supported the principle of a settlement based on democratization of the Northern Irish state, which was later accepted by Sinn Féin in the form of the Belfast Agreement. The goal of my research is to provide a novel perspective on the conflict in Northern Ireland, while engaging with theoretical debates about its character.