Obtenção de fotocatalisadores magnéticos a partir de resíduos industriais e TiO2 para a degradação de contaminantes orgânicos

In this work, magnetic photocatalysts were synthesized containing differents levels of TiO2 (40, 60 e 80%) supported at the supporter of C/LV, forming the photocatalysts 40, 60, 80Ti/C/LV, using tar pitch as carbon (C) source and red mud (LV) as iron source. The prepared magnetic photocatalysts and TiO2 were used to degrade the Remazol Black textile dye (PR5) and the organic material present in samples of a textile dye effluent. The characterization of photocatalysts by Raman, X-Ray Diffraction, Transmission Electron Micoscope and Scanning, Energy Dispersive X-ray Spectrometry, Termogravimetry and Elemental Analysis, confirms the presence of carbon and magnetite in support C/LV and the presence of TiO2 in prepared photocatalysts. The photocatalytic reactions with TiO2 were analyzed by different experimental conditions, such as: mass of TiO2 (30-240 mg), solution pH (2-10), light intensity (0.871 and 1.20 mWcm-2), type of radiation (UV and sunlight-1.420 mWcm-2), radiation incidence area (44.2 to 143.1 cm2) and dissolved oxygen (OD, 1.9 and 7.6 mg L- 1). Results showed that reactions with the following conditions: 220 mg of TiO2, pH 10, solar radiation, 7.6 mg L-1 of OD and an incidence area of radiation of 143.1 cm2 showed the best results for degradation of PR5 dye. Photocatalytic reactions with magnetic photocatalysts for degrading PR5 shows that efficiency increases with TiO2 content in the C/LV support, where, above 60% of TiO2, there was not significant increase in reaction velocity. In addition, solar radiation has proved to be advantageous for photocatalytic reactions. In order to verify the presence of a non-magnetic fraction in the photocatalyst 60Ti/C/LV0, magnetic separation was proceeded. The characterizations of the magnetic (FM) and nonmagnetic (NMF) fraction confirmed that about 25% of TiO2 did not fixed in 60Ti/C/LV photocatalyst. Results of photocatalytic reactions with FM and FNM showed that both phases have photocatalytic activity for degradation of PR5. The reactions executed for the degradation of organic matter present in the actual sample of textile effluent showed that TiO2 and magnetic photocatalyst 60Ti/C/ LV have better results for color removal (85 to 35%), soluble solids ( 11 and 3%), DQO (90 and 86%) and turbidity (94 and 11%) than the treatment done by the textile industry. Sedimentation kinetics tests in presence of a magnet showed that photocatalysts are separated faster from aqueous environment than pure TiO2. Obtained results showed that magnetic photocatalysts have excellent photocatalytic activity and can be separated from the reaction environment on a simple and quick way when a magnetic field is applied.

Análise energética da madeira e do carvão de híbridos entre Corymbia citriodora (Hook.) K.D. Hill & L.A.S. Johnson e Corymbia torelliana (F. Muell.) K.D. Hill & L.A.S. Johnson

This research aimed to evaluate the wood and charcoal quality of hybrids clone of the crossing C. citriodora with C. torelliana in two different locations for charcoal production. Seven with 3,75 years old clones, planted at country of Itamarandiba – MG, and six 6,42 years old clones, planted in Dionísio – MG, were studied. For wood and charcoal quality analysis, samples were collected along the stem of the trees until the commercial height. Properties study of the wood was done by chemical analysis, basic density, superior heat power, and thermogravimetric analysis. The wood samples were carbonized in laboratory conditions with heating rate of 1.67 0 C.min -1 , starting at 100 0 C until 450 0 C and keeping on this temperature for 30 minutes. It were determined the carbonizations gravimetric yield, all in dry basis. The wood quality was evaluated based on the chemical immediate analysis, relative apparent density, and gross heating value. The experiment was installed according to the completely randomized design, with five repetitions. The collected data were submitted to analysis of variance and, when the evaluated effects were significant by “F” test, was applied the Scott-Knott test at 5% probability for multiple comparisons. For correlation analysis, Pearson correlation coefficient, tested by the "t" test at 5% probability was used. Results showed variability of wood between the genetic materials evaluated in relation to place and plant crossing. The thermal analysis of the wood showed significant variation between clones and it was possible to differentiate two stages of degradation (hemicelluloses and cellulose). The majority of the clones presented satisfactory properties for the charcoal production, while, clone 3, planted in Itamarandiba, obtained the best performance due it have the higher yield and energetic efficiency, thus, achieving the best potential for charcoal production. However, clone 9, planted in Dionísio, was the less indicated for charcoal production since it presented the lowest energetic efficiency, gravimetric yield, and densities.