Biological Characteristics and Thermal Requirements of the Biological Control Agent Telenomus remus (Hymenoptera: Platygastridae) Reared on Eggs of Different Species of the Genus Spodoptera (Lepidoptera: Noctuidae)

The biological characteristics of Telenomus remus Nixon, 1937 (Hymenoptera: Platygastridae) on eggs of Spodoptera albula (Walker, 1857); S. cosmioides Walker 1858, S. eridania (Cramer, 1782); and S. frugiperda (Smith, 1797) (Lepidoptera: Noctuidae) were evaluated under different temperatures (19, 22, 25, 28, 31, and 34 degrees C +/- 1 degrees C). The duration of the T remus egg-to-adult period on eggs of all four Spodoptera species and the longevity of adults of T. remus were both inversely proportional to the increase in temperature. Parasitoid emergence was higher than 80% at temperatures from 19 to 28 degrees C when the parasitoid was reared on eggs of S. eridania and S. frugiperda. Differently, when the parasitoid was reared on eggs of S. albula and S. cosmioides, T. remus emergence at rates of 80% or higher just occurred from 22 to 25 degrees C and at 22 degrees C, respectively. At 34 degrees C, this parameter was lower than 30% for T reams reared in all hosts. The sex ratio was 64-86% females, except for T. remus in S. cosmioides eggs at 34 C, in which temperature it was 39%. The estimated thermal requirements of T. remus, for the thermal constant (K) and the base temperature (T(base)), were: 125.39 DD and 15.139 degrees C; 125.56 DD and 14.912 degrees C; 142.98 DD and 14.197 degrees C; and 149.16 DD and 13.846 degrees C, for S. cosmioides, S. frugiperda, S. albula, and S. eridania, respectively. In general, T. remus showed good parasitism potential on all the hosts, although eggs of S. frugiperda, S. eridania, and S. albula proved to be the most suitable for mass rearing of T reams in the laboratory. Eggs of S. cosmioides are less suitable because of the lower parasitoid emergence observed at most of the temperatures with exception of 22 degrees C.

Residual stresses in Y-TZP crowns due to changes in the thermal contraction coefficient of veneers

Objective. To test the hypothesis that the difference in the coefficient of thermal contraction of the veneering porcelain above (˛liquid) and below (˛solid) its Tg plays an important role in stress development during a fast cooling protocol of Y-TZP crowns. Methods. Three-dimensional finite element models of veneered Y-TZP crowns were developed. Heat transfer analyses were conducted with two cooling protocols: slow (group A) and fast (groups B–F). Calculated temperatures as a function of time were used to determine the thermal stresses. Porcelain ˛solid was kept constant while its ˛liquid was varied, creating different ˛/˛solid conditions: 0, 1, 1.5, 2 and 3 (groups B–F, respectively). Maximum ( 1) and minimum ( 3) residual principal stress distributions in the porcelain layer were compared. Results. For the slowly cooled crown, positive 1 were observed in the porcelain, orientated perpendicular to the core–veneer interface (“radial” orientation). Simultaneously, negative 3 were observed within the porcelain, mostly in a hoop orientation (“hoop–arch”). For rapidly cooled crowns, stress patterns varied depending on ˛/˛solid ratios. For groups B and C, the patterns were similar to those found in group A for 1 (“radial”) and 3 (“hoop–arch”). For groups D–F, stress distribution changed significantly, with 1 forming a “hoop-arch” pattern while 3 developed a “radial” pattern. Significance. Hoop tensile stresses generated in the veneering layer during fast cooling protocols due to porcelain high ˛/˛solid ratio will facilitate flaw propagation from the surface toward the core, which negatively affects the potential clinical longevity of a crown.