Fatty acid profile, trans-octadecenoic, alpha-linolenic and conjugated linoleic acid contents differing in certified organic and conventional probiotic fermented milks

Development of dairy organic probiotic fermented products is of great interest as they associate ecological practices and benefits of probiotic bacteria. As organic management practices of cow milk production allow modification of the fatty acid composition of milk (as compared to conventional milk), we studied the influence of the type of milk on some characteristics of fermented milks, such as acidification kinetics. bacterial counts and fatty acid content. Conventional and organic probiotic fermented milks were produced using Bifidobacterium animalis subsp. lactis HN019 in co-culture with Streptococcus thermophilus TA040 and Lactobacillus delbrueckii subsp. bulgaricus LB340. The use of organic milk led to a higher acidification rate and cultivability of Lactobacillus bulgaricus. Fatty acids profile of organic fermented milks showed higher amounts of trans-octadecenoic acid (C18:1, 1.6 times) and polyunsaturated fatty acids, including cis-9 trans-11. C18:2 conjugated linoleic (CLA-1.4 times), and alpha-linolenic acids (ALA-1.6 times), as compared to conventional fermented milks. These higher levels were the result of both initial percentage in the milk and increase during acidification, with no further modification during storage. Finally, use of bifidobacteria slightly increased CLA relative content in the conventional fermented milks, after 7 days of storage at 4 degrees C, whereas no difference was seen in organic fermented milks. (C) 2012 Elsevier Ltd. All rights reserved.

Foraminifera as indicators of marine pollutant contamination on the inner continental shelf of southern Brazil

Analyses of living foraminiferal and environmental parameters near an outfall at Mar Grosso Beach (Laguna, SC, Brazil) demonstrate its usefulness as indicators of domestic sewage pollution. The low species diversity may be due to sand accumulation in the central part. Higher diversity was noted closer to the mouth of Laguna estuarine system where reduced salinity and higher temperatures indicate freshwater influence, suggesting a relationship between increased diversity and greater availability of terrestrial food. On the basis of foraminiferal diversity and average coliform count the higher values are closer to the mouth of the estuarine system and under the influence of the outfall. Due to the effect of local hydrodynamics, the particulate organic waste derived from the outfall does not settle down locally, and thus, do not accumulate nearby. Our hypothesis is that the fine material derived from the outfall is accumulating on the southwestern and northwestern parts of the beach.

Sequential extraction of phosphorus in an Oxisol amended with biosolids in a long-term field experiment in Brazil

The continued growth of large cities is producing increasing volumes of urban sewage sludge. Disposing of this waste without damaging the environment requires careful management. The application of large quantities of biosolids (treated sewage sludge) to agricultural lands for many years may result in the excessive accumulation of nutrients like phosphorus (P) and thereby raise risks of eutrophication in nearby water bodies. We evaluated the fractionation of P in samples of an Oxisol collected as part of a field experiment in which biosolids were added at three rates to a maize (Zea mays L) plantation over four consecutive years. The biosolids treatments were equivalent to one, two and four times the recommended N rate for maize crops. In a fourth treatment, mineral fertilizer was applied at the rate recommended for maize. Inorganic P forms were extracted with ammonium chloride to remove soluble and loosely bound P; P bound to aluminum oxide (P-Al) was extracted with ammonium fluoride; P bound to iron oxide (P-Fe) was extracted with sodium hydroxide; and P bound to calcium (P-Ca) was extracted with sulfuric acid. Organic P was calculated as the difference between total P and inorganic P. The predominant fraction of P was P-Fe, followed by P-Al and P-Ca. P fractions were positively correlated to the amounts of P applied, except for P-Ca. The low values of P-Ca were due to the advanced weathering processes to which the Oxisol have been subjected, under which forms of P-Ca are converted to P-Fe and P-Al. The fertilization with P via biosolids increased P availability for maize plants even when a large portion of P was converted to more stable forms. Phosphorus content in maize leaves and grains was positively correlated with P fractions in soils. From these results it can be concluded that the application of biosolids in highly weathered tropical clayey soils for many years, even above the recommended rate based on N requirements for maize, tend to be less potentially hazardous to the environment than in less weathered sandy soils because the non-readily P fractions are predominant after the addition of biosolids. (C) 2012 Elsevier B.V. All rights reserved.

Faeces deposition on Amazonian Anthrosols as assessed from 5 beta-stanols

In the Amazon Basin, within a landscape of infertile soils, fertile Anthrosols of pre-Columbian origin occur (Amazonian Dark Earths or terra preta de Indio). These soils are characterized by high amounts of charred organic matter (black carbon, biochar) and high nutrient stocks. Frequently, they were considered as sign for intensive landscape domestication by way of sedentary agriculture and as sign for large settlements in pre-Columbian Amazonia. Beyond the archaeological interest in Amazonian Dark Earths, they increasingly receive attention because it is assumed that they could serve as a model for sustainable agriculture in the humid tropics (terra preta nova). Both questions lack information about the pre-Columbian practices which were responsible for the genesis of Amazonian Dark Earths. It has often been hypothesized that deposition of faeces could have contributed to the high nutrient stocks in these soils, but no study has focussed on this question yet. We analyzed the biomarkers for faeces 5 beta-stanols as well as their precursors and their 5 alpha-isomers in Amazonian Dark Earths and reference soils to investigate the input of faeces into Amazonian Dark Earths. Using Amazonian Dark Earths as example, we discuss the application of threshold values for specific stanols to evaluate faeces deposition in archaeological soils and demonstrate an alternative approach which is based on a comparison of the concentration patterns of 5 beta-stanols with the concentration patterns of their precursors and their 5 alpha-isomers as well as with local backgrounds. The concentration patterns of sterols show that faeces were deposited on Amazonian Dark Earths. (C) 2011 Elsevier Ltd. All rights reserved.

Performance and composition of bacterial communities in anaerobic fluidized bed reactors for hydrogen production: Effects of organic loading rate and alkalinity

This study evaluated the effects of the organic loading rate (OLR) and pH buffer addition on hydrogen production in two anaerobic fluidized bed reactors (AFBRs) operated simultaneously. The AFBRs were fed with glucose, and expanded clay was used as support material. The reactors were operated at a temperature of 30 degrees C, without the addition of a buffer (AFBR1) and with the addition of a pH buffer (AFBR2, sodium bicarbonate) for OLRs ranging from 19.0 to 140.6 kg COD m(-3) d(-1) (COD: chemical oxygen demand). The maximum hydrogen yields for AFBR1 and AFBR2 were 2.45 and 1.90 mol H-2 mol(-1) glucose (OLR of 84.3 kg COD m(-3) d(-1)), respectively. The highest hydrogen production rates were 0.95 and 0.76 L h(-1) L-1 for AFBR1 and AFBR2 (OLR of 140.6 kg COD m(-3) d(-1)), respectively. The operating conditions in AFBR1 favored the presence of such bacteria as Clostridium, while the bacteria in AFBR2 included Clostridium, Enterobacter, Klebsiella, Veillonellaceae, Chryseobacterium, Sporolactobacillus, and Burkholderiaceae. Copyright (C) 2012, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Rice husk derived waste materials as partial cement replacement in lightweight concrete

In this study rice husk ash (RHA) and broiler bed ash from rice husk (BBA), two agricultural waste materials, have been assessed for use as partial cement replacement materials for application in lightweight concrete. Physical and chemical characteristics of RHA and BBA were first analyzed. Three similar types of lightweight concrete were produced, a control type in which the binder was just CEMI cement (CTL) and two other types with 10% cement replacement with, respectively, RHA and BBA. All types of similar lightweight concrete were prepared to present the same workability by adjusting the amount of superplasticizer. Properties of concrete investigated were compressive and flexural strength at different ages, absorption by capillarity, resistivity and resistance to chloride ion penetration (CTH method) and accelerated carbonation. Test results obtained for 10% cement replacement level in lightweight concrete indicate that although the addition of BBA conducted to lower performance in terms of the degradation indicative tests, RHA led to the enhancement of mechanical properties, especially early strength and also fast ageing related results, further contributing to sustainable construction with energy saver lightweight concrete.

Hydrogen production and consumption of organic acids by a phototrophic microbial consortium

Alternative fuel sources have been extensively studied. Hydrogen gas has gained attention because its combustion releases only water, and it can be produced by microorganisms using organic acids as substrates. The aim of this study was to enrich a microbial consortium of photosynthetic purple non-sulfur bacteria from an Upflow Anaerobic Sludge Blanket reactor (UASB) using malate as carbon source. After the enrichment phase, other carbon sources were tested, such as acetate (30 mmol l(-1)), butyrate (17 mmol l(-1)), citrate (11 mmol l(-1)), lactate (23 mmol l(-1)) and malate (14.5 mmol l(-1)). The reactors were incubated at 30 degrees C under constant illumination by 3 fluorescent lamps (81 mu mol m(-2) s(-1)). The cumulative hydrogen production was 7.8, 9.0, 7.9, 5.6 and 13.9 mmol H-2 l(-1) culture for acetate, butyrate, citrate, lactate and malate, respectively. The maximum hydrogen yield was 0.6, 1.4, 0.7, 0.5 and 0.9 mmol H-2 mmol(-1) substrate for acetate, butyrate, citrate, lactate and malate, respectively. The consumption of substrates was 43% for acetate, 37% for butyrate, 100% for citrate, 49% for lactate and 100% for malate. Approximately 26% of the clones obtained from the Phototrophic Hydrogen-Producing Bacterial Consortium (PHPBC) were similar to Rhodobacter, Rhodospirillum and Rhodopseudomonas, which have been widely cited in studies of photobiological hydrogen production. Clones similar to the genus Sulfurospirillum (29% of the total) were also found in the microbial consortium. Copyright (C) 2012, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Work and technological innovation in organic agriculture

Organic agriculture is a sustainable cultivation ecologically, economically and socially. Several researches in organic agriculture have been made from technical perspectives, economic traits or related to ecological aspects. There are practically no investigations into the nature of the technology used in organic agriculture, especially from an ergonomic perspective. From the activity analysis, this study aimed to map the technology used in the production of organic vegetables. Properties producing organic vegetables were selected representing the State of Sao Paulo. It was applied an instrument (questionnaire and semi-structured interview) with their managers and it was made visual records to identify adaptations, innovations and technological demands that simultaneously minimize the workload and the difficulties in performing the tasks and increase work productivity. For some of the technological innovations a digital scanner was used to generate a virtual solid model to facilitate its redesign and virtual prototyping. The main results show that organic farmers have little technology in product form. The main innovations that enable competitive advantage or allow higher labor productivity occur in the form of processes, organization and marketing.

Hydrogen and Methane Production, Energy Recovery, and Organic Matter Removal from Effluents in a Two-Stage Fermentative Process

This study evaluates the potential for using different effluents for simultaneous H-2 and CH4 production in a two-stage batch fermentation process with mixed microflora. An appreciable amount of H-2 was produced from parboiled rice wastewater (23.9 mL g(-1) chemical oxygen demand [COD]) and vinasse (20.8 mL g(-1) COD), while other effluents supported CH4 generation. The amount of CH4 produced was minimum for sewage (46.3 mL g(-1) COD), followed by parboiled rice wastewater (115.5 mL g(-1) COD) and glycerol (180.1 mL g(-1) COD). The maximum amount of CH4 was observed for vinasse (255.4 mL g(-1) COD). The total energy recovery from vinasse (10.4 kJ g(-1) COD) corresponded to the maximum COD reduction (74.7 %), followed by glycerol (70.38 %, 7.20 kJ g(-1) COD), parboiled rice wastewater (63.91 %, 4.92 kJ g(-1) COD), and sewage (51.11 %, 1.85 kJ g(-1) COD). The relatively high performance of vinasse in such comparisons could be attributed to the elevated concentrations of macronutrients contained in raw vinasse. The observations are based on kinetic parameters of H-2 and CH4 production and global energy recovery of the process. These observations collectively suggest that organic-rich effluents can be deployed for energy recovery with sequential generation of H-2 and CH4.

CHARACTERIZATION OF REGOSOLS IN THE SEMIARID REGION OF PERNAMBUCO, BRAZIL

CHARACTERIZATION OF REGOSOLS IN THE SEMIARID REGION OF PERNAMBUCO, BRAZIL Studies on soil characterization in unexplored regions, besides the generation of data banks for the soil classes of the country, also produce scientific information about soil properties, important for the development of good management practices and sustainable land use. One of the main soil classes in the semiarid region of Pernambuco State, the Regosols, cover about 27 % of the state area, and are used mainly for family agriculture. Due to different geological and climatic aspects Regosols with different chemical, physical and mineralogical properties are found in Pernambuco, which were characterized for the semiarid region of the State. Five Regosol profiles were selected in different regions of the State (P1=Sao Caetano; P2=Lagoa do Ouro; P3=Caetes; P4=Sao Joao; P5=Parnamirim). The soils were morphologically characterized and samples collected from all horizons and the bedrock. Routine physical and chemical analyses were carried out for soil classification of all samples and mineralogical analyses of the coarse fractions (gravel and sand) by optical microscopy and of the silt and clay fractions by X ray diffraction (XRD), as well as petrographic analyses of the rock samples. The results showed similarities between the soils, with a low degree of pedogenetic development, varying from medium to very deep, with the horizon sequence A-AC-C-Cr and a sandy to sandy loam texture. In the deeper layers of two profiles (P1 and P5), a solodic character was observed. Organic matter and available phosphorus content were low in all studied soils. Despite the low levels of exchangeable cations, all soil profiles showed high base saturation. The mineralogical composition of gravel, sand and silt fractions consisted, essentially, of quartz, followed by feldspars and mica, supporting the results of the petrographic analysis of the bedrock. Kaolinite was the main clay mineral in all studied profiles and horizons, indicating an important monosialitization process in autochthonous soils of a typical semiarid region. In soil profile P2, at a lower landscape position, smectite minerals were observed, with mixing phases of montmorillonite, beidelite or nontronite, indentified by the Greene-Kelly test in the DRX analysis.

Rice husk derived waste materials as partial cement replacement in lightweight concrete

In this study rice husk ash (RHA) and broiler bed ash from rice husk (BBA), two agricultural waste materials, have been assessed for use as partial cement replacement materials for application in lightweight concrete. Physical and chemical characteristics of RHA and BBA were first analyzed. Three similar types of lightweight concrete were produced, a control type in which the binder was just CEMI cement (CTL) and two other types with 10% cement replacement with, respectively, RHA and BBA. All types of similar lightweight concrete were prepared to present the same workability by adjusting the amount of superplasticizer. Properties of concrete investigated were compressive and flexural strength at different ages, absorption by capillarity, resistivity and resistance to chloride ion penetration (CTH method) and accelerated carbonation. Test results obtained for 10% cement replacement level in lightweight concrete indicate that although the addition of BBA conducted to lower performance in terms of the degradation indicative tests, RHA led to the enhancement of mechanical properties, especially early strength and also fast ageing related results, further contributing to sustainable construction with energy saver lightweight concrete.