Vertical growth of mini watermelon according to the training height and plant density

The watermelon is traditionally cultivated horizontally on the ground. The cultivars of small fruits (1 to 3 kg), which reach better market prices, are also being grown in a greenhouse, where the plants are trained upward on vertical supports, with branches pruning and fruits thinning. These practices make possible an increase of the plant density, fruit quality and yield compared to the traditional growth system. The aim of this experiment was to evaluate the influence of three training heights (1.7, 2.2 and 2.7 m) and two planting densities (3.17 and 4.76 plants m-2) over the productive and qualitative characteristics of mini watermelon "Smile" cultivated in greenhouse. The pruning was done at 43, 55 and 66 days after transplanting (DAT), when the plant height reached 1.7, 2.2 and 2.7 m, respectively. The dry mass of branches, petioles, leaves and total were affected by the training height, where the highest values were obtained by the plants pruned at 2.2 and 2.7 m. Leaf area, specific leaf area and leaf area index were not affected by the height of the plants. The training height of 2.7 m raised the total yield, however, marketable yield, average fruit mass and all the quality characteristics did not differ significantly from those obtained by the training height of 2.2 m. Regarding to plant density, the best option was 4.76 plants m-2, due to the increasing of marketable yield in 37.4% without reducing the average weight of fruits.

In vitro organogenesis of zucchini squash cv. Caserta

A protocol for the in vitro culture of Cucurbita pepo cv. Caserta was studied, using a cotyledon segment with an attached hypocotyl fragment as an explant. First, to determine the optimal seedling age, explants were collected from 4 to 6-day-old in vitro germinated seedlings and cultured in MS basal medium supplemented with benzylaminopurine (BAP, 4.5 mu M), under a 16-h photoperiod at 27 degrees C. Based on the results obtained, the explants collected from the 4-day-old seedlings were then cultured in MS basal medium supplemented with different concentrations of BAP (0, 1.1, 2.2, 3.3, 4.5, or 5.5 mu M) and incubated under a 16-h photoperiod at 27 degrees C. In vitro organogenesis was most efficient with explants collected from 4-day-old seedlings cultured in medium supplemented with 4.5 mu M of BAP. After 4 weeks of incubation the development of adventitious buds at the cotyledon/hypocotyl junction could be observed. These buds were transferred to elongation and rooting medium and the developed plants were acclimatized to greenhouse conditions. The morphogenic process was characterized using light and scanning electron microscopy analyses to confirm the organogenesis. The results showed that this alternate explant is efficient for in vitro culture of zucchini squash cv. Caserta. The protocol will be further examined for future use in genetic transformation experiments in this species.

X-ray densitometry to assess internal seed morphology and quality

Non-destructive procedures are desirable for a precise internal seed morphology assessment. In this research the efficiency of X-ray densitometry for internal seed morphology analysis and physical quality of squash, melon and watermelon was evaluated. Seeds were submitted to X-ray densitometry and a typical density profile for each seed was generated. Based on the detailed densitometry profiles it was possible indicate density values for specific seed regions of the seeds and identify causes of poor germination. X-ray densitometry was considered as a promising non-destructive procedure to evaluate internal seed morphology of squash, melon and watermelon and demonstrated a strong potential for further research in seed testing.

Microparticulated Hydrochlorothiazide Solid Dispersion: Enhancing Dissolution Properties via Spray Drying

The aim of the present study was to obtain microparticles of hydrochlorothiazide, a diuretic drug that practically insoluble in water, by spray drying and to investigate the influence of process parameters using a three-level, three-factor Box-Behnken design. Process yields, moisture content, particle size, flowability, and solubility were used to evaluate the spray-dried microparticles. The data were analyzed by response surface methodology using analysis of variance. The independent variables studied were outlet temperature, atomization pressure, and drug content. The formulations were prepared using polyvinylpyrrolidone and colloidal silicon dioxide as the hydrophilic carrier and drying aid, respectively. The microparticle yield ranged from 18.15 to 59.02% and resulted in adequate flow (17 to 32 degrees), moisture content between 2.52 to 6.18%, and mean particle size from 45 to 59 mu m. The analysis of variance showed that the factors studied influenced the yields, moisture content, angle of repose, and solubility. Thermal analysis and X-ray diffractometry evidenced no drug interactions or chemical modifications. Photomicrographs obtained by scanning electron microscopy showed spherical particles. The solubility and dissolution rates of hydrochlorothiazide were remarkably improved when compared with pure drug. Therefore, the results confirmed the high potential of the spray-drying technique to obtain microparticulate hydrochlorothiazide with enhanced pharmaceutical and dissolution properties.