The revision of the Brazilian Forest Act: increased deforestation or a historic step towards balancing agricultural development and nature conservation?

Almost two-thirds of the Brazilian territory still has prevalence of natural vegetation. Although not all pristine, much of these areas have high conservation value. 170 million hectare (Mha) of the natural vegetation is located within Federal and State protected areas. Most of the remaining 367 Mha is on private agriculture lands, where the Forest Act is the most important legal framework for conservation. In July 2010, the Brazilian parliament began the analysis of a substitutive legislation for the Forest Act. The main motivations for the revision is that, on the one hand, it has been found ineffective in protecting natural vegetation, and on the other hand, it is perceived as a barrier against development in the agriculture sector. The substitutive Forest Act, as it presently stands, does not represent a balance between existing standpoints and objectives; it may drive development towards either more private protection through market-driven compensation actions, or increased deforestation and less nature protection/restoration. This article uses outcomes from modeling analyses to discuss weaknesses of the substitutive Forest Act and to suggest possible improvements. (C) 2011 Elsevier Ltd. All rights reserved.

Understanding the mechanical and biodegradation behaviour of poly(hydroxybutyrate)/rubber blends in relation to their morphology

In this work poly(hydroxybutyrate/poly(vinyl butyral)- co-(vinyl alcohol)-co(vinyl acetate) (or ethylene propylene diene monomer rubber) blends were prepared by conventional processing techniques (extrusion and injection moulding). A droplet type morphology was obtained for P(3HB)/PVB blends whereas P(3HB)/EPDM blends presented some extent of co-continuous morphology. In addition, rubbery domains were much smaller in the case of PVB. These differences in morphology are discussed taking into account solubility parameters and rheological behaviours of each component. For both blends, the increase of elastomer ratio led to a decrease of Young's modulus but an increase in elongation at break and impact strength. The latter increased more in the case of P(3HB)/EPDM blends although the rubbery domains were larger. These results are explained in the light of the glass transition of the rubber and the presence of plasticizer in the case of PVB. The addition of elastomer also resulted in an increase of P(3HB) biodegradation rate, especially in the case of EPDM. It is assumed that, in this case, the size and morphology of the rubbery domains induce a geometrical modification of the erosion front which leads to an increase of the interface between P(3HB) phase and the degradation medium and consequently to an apparently faster biodegradation kinetics of PHB/rubber blends. Copyright (C) 2011 Society of Chemical Industry

Use of cellulose fibers from hemp core in fiber-cement production. Effect on flocculation, retention, drainage and product properties

The aim of this paper is to study the feasibility of using cellulose fibers obtained from an agricultural waste, hemp core (Cannabis Sativa L), through different new environmental friendly cooking processes for fiber-cement production. The physical and mechanical properties of the fiber reinforced concrete, which depend on the nature and morphology of the fibers, matrix properties and the interactions between them, must be kept between the limits required for its application. Therefore, the morphology of the fibers and how its use affects the flocculation, retention and drainage processes in the fiber-cement manufacture, and the mechanical and physical properties of the fiber-cement product have been studied. The use of pulp obtained by means of the hemp core cooking in ethanolamine at 60% concentration at 180 degrees C during 90 min resulted in the highest solids retention and the best mechanical properties among the studied hemp core pulps. (C) 2012 Elsevier B.V. All rights reserved.

Influence of the relative amounts of crystalline and amorphous phases on the mechanical properties of polyamide-6 nanocomposites

The relative amounts of amorphous and crystalline ?- and a-phases in polyamide-6 nanocomposites, estimated from the deconvolution of X-ray diffraction peaks using Gaussian functions, correlates with their mechanical, thermomechanical, and barrier properties. The incorporation of organoclay platelets (Cloisite 15A and 30B) induced the crystallization of the polymer in the ? form at expense of the amorphous phase, such that 12 wt % of Cloisite is enough to enhance the mechanical and the thermomechanical properties. However, higher nanofiller loads were necessary to achieve good barrier effects, because this property is mainly dependent on the tortuous path permeation mechanism of the gas molecules through the nanocomposite films. (C) 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012

Lung morphology and growth of rats exposed to tobacco smoke and alcohol

PURPOSE: Investigate the morphological effects of chronic exposure to tobacco smoke inhalation and alcohol consumption on the lungs and on the growth of rats. METHODS: Sixty male Wistar rats were divided into four groups: control, tobacco, alcohol, tobacco + alcohol, for a period of study 260 days. Morphological analysis was conducted by optical and electron microscopy. Rat growth was investigated by measuring the snout-anus length, body mass index and body weight. RESULTS: The three groups exposed to the drugs presented lower growth and lower weight than the control group. The percentages of alveolitis, bronchiolitis and the mean alveolar diameter were greater, particularly in the groups exposed to tobacco smoke, but were not significantly different from the control group. Electron microscopy revealed more intense apoptotic and degenerative lesions in the smoking group, while degenerative lesions in the lamellar bodies were more intense with the association of both drugs. CONCLUSIONS: This experimental model showed morphological alterations observed by electron microscopy, principally due to tobacco smoke exposure. Alcohol and tobacco hindered the growth of rats, such that tobacco showed a greater effect on body length and alcohol on body weight.