Raman and XRD study on brookite-anatase coexistence in cathodic electrosynthesized titania

Among the many methods developed for the synthesis of titanium dioxide, cathodic electrosynthesis has not received much attention because the resulting amorphous oxy-hydroxide matrix demands a further thermal annealing step to be transformed into crystalline titania. However, the possibility of filling deep recessed templates by the control of the solidliquid interface makes it a potentially suitable technique for the fabrication of porous scaffolds for photovoltaics and photocatalysis. Furthermore, a careful control of the crystallization process enables the growth of larger grains with lower density of grain boundaries, which act as electron traps that slow down electronic transport and promote charge recombination. In this report, well crystallized titania deposits were obtained by thermal annealing of amorphous deposits fabricated by cathodically assisted electrosynthesis on indium-tin oxide (ITO)substrates. The combined use of Raman spectroscopy and X-ray diffraction showed that the crystallization process is more intricate than previously assumed. It is shown that the amorphous matrix evolves into a rutile-free mixture of brookite and anatase at temperatures as low as 200 degrees C that persists up to 800 degrees C, when pure anatase dominates. The amount of brookite in the brookiteanatase mixture reaches a maximum at 400 degrees C. This very simple method for obtaining a brookiteanatase mixture and the ability to tune their proportions by thermal annealing is a promising alternative whose potential for solar cells and photocatalysis deserves a careful evaluation. Copyright (C) 2011 John Wiley & Sons, Ltd.

Palynostratigraphy and sedimentary facies of Middle Miocene fluvial deposits of the Amazonas Basin, Brazil

Palynostratigraphic and sedimentary fades analyses were made on sedimentary deposits from the left bank of the Solimoes River, southwest of Manaus. State of Amazonas, Brazil. These provided the age-elating and subdivision of a post-Cietaceous stratigraphic succession in the Amazonas Basin. The Novo Remanso Formation is subdivided into upper and lower units, and delineated by discontinuous surfaces at its top and bottom. The formation consists primarily of sandstones and minor mudstones and conglomerates, reflecting fluvial channel, point bar and floodplain facies of a fluvial meandering paleosystem. Fairly well-preserved palynoflora was recovered from four palynologically productive samples collected in a local irregular concentration of gray clay deposits, rich in organic material and fossilized wood, at the top of the Nova Remanso Formation upper unit. The palynoflora is dominated by terrestrial spores and pollen grains, an d is characterized by abundant angiosperm pollen grains (Tricolpites, Grimsdalea, Perisyncolporites, Tricolporites and Malvacearumpollis). Trilete spores are almost as abundant as the angiosperm pollen, and are represented mainly by the genera Deltoidospora. Verrutriletes, and Hamulatisporis. Gymnosperm pollen is scarce. The presence of the index species Grimsdalea magnaclavata Germeraad et al. (1968) indicates that these deposits belong to the Middle Miocene homonymous palynozone (Lorente, 1986; Hoorn, 1993; Jaramillo et al., 2011). Sedimentological characteristics (poorly sorted, angular to sub-angular, fine to very-coarse quartz sands facies) are typical of the NOW Remanso Formation upper part. These are associated with a paleoflow to the NE-E and SE-E, and with a a entirely lowland-derived palinofloristic content with no Andean ferns and gymnosperms representatives. All together, this suggests a cratonic origin for this Middle Miocene fluvial paleosystem, which was probably born in the Purus Arch eastern flank and areas surrounding the crystalline. The palynological analysis results presented herein are the first direct and unequivocal evidence of the occurrence of Middle Miocene deposits in the central part of the Amazonas Basin. They also provide new perspectives for intra- and interbasin correlations, as well as paleogeographic and paleoenvironmental interpretations for the later deposition stages in the northern Brazilian sedimentary basins. (C) 2011 Elsevier Ltd. All rights reserved.

Seismites as a tool in the palaeoenvironmental reconstruction of fluvial deposits: The Cambrian Guarda Velha Formation, southern Brazil

Soft-sediment deformation (SSD) is widely described in the literature, but there is no clear consensus regarding its origin and significance. Existing models for SSD in fluvial sediments do not clearly demonstrate a relationship between the structures, preserved facies expression, and larger-scale depositional architecture. In this study several types of SSD structures are recorded in Cambrian fluvial deposits and these occur interbedded with undeformed strata throughout the entire stratigraphic interval. The random distribution of these features in relation to primary facies types and fluvial forms indicates that they have neither a direct nor indirect relationship with any depositional processes or bedform type. We propose that the relationship of SSD at the bed-set-scale to larger-scale depositional architecture, combined with tectono-stratigraphic analysis allows the determination of both short-term fluvial hydraulic conditions in ancient stream systems, such as the nature of the flow regime responsible for depositing ancient fluvial stream successions, and the long-term subsidence rates, in the form of mean recurrence interval of the seismic events responsible for triggering the generation of SSD in tectonically active basins. (c) 2012 Elsevier B.V. All rights reserved.

Degradation of [D-Leu]-Microcystin-LR by solar heterogeneous photocatalysis (TiO2)

The present study investigates the use of solar heterogeneous photocatalyis (TiO2) for the destruction of [D-Leu]-Microcystin-LR, powerful toxin of widespread occurrence within cyanobacteria blooms. We extracted [D-Leu]-Microcystin-LR from a culture of Microcystis spp. and used a flat plate glass reactor coated with TiO2 (Degussa, P25) for the degradation studies. The irradiance was measured during the experiments with the aid of a spectroradiometer. After the degradation experiments, toxin concentrations were determined by HPLC and mineralization by TOC analyses. Acute and chronic toxicities were, quantified using mice and phosphatase inhibition in vitro assays, respectively. According to the performed experiments, 150 min were necessary to reduce the toxin concentration to the WHO's guideline for drinking water (from 10 to 1 mu g L-1) and to mineralize 90% of the initial carbon content. Another important finding is that solar heterogeneous photocatalysis was a destructive process indeed, not only for the toxin, but also for the other extract components and degradation products generated. Moreover, toxicity tests using mice have shown that the acute effect caused by the initial sample was removed. However, tests using the phosphatase enzyme indicated that it may be formed products capable of inducing chronic effects on mammals. The performed experiments indicate the feasibility of using solar heterogeneous photocatalysis for treating contaminated water with [D-Leu]-Microcystin-LR, not only due to its destruction, but also to the significant removal of organic matter and acute toxicity that can be achieved. (C) 2012 Elsevier Ltd. All rights reserved.

Dendrimers/TiO2 nanoparticles layer-by-layer films as extended gate FET for pH detection

The layer-by-layer (LbL) technique combined with field-effect transistor (FET) based sensors has enabled the production of pH-sensitive platforms with potential application in biosensors. A variation of the FET architecture, so called separative extended gate FET (SEGFET) devices, are promise as an alternative to conventional ion sensitive FET (ISFET). SEGFET configuration exhibits the advantage of combining the field-effect concept with organic and inorganic materials directly adsorbed on the extended gate, allowing the test of new pH-sensitive materials in a simple and low cost way. In this communication, poly(propylene imine) dendrimer (PPI) and TiO2 nanoparticles (TiO2-np) were assembled onto gold-covered substrates via layer-by-layer technique to produce a low cost SEGFET pH sensor. The sensor presented good pH sensitivity, ca. 57 mV pH(-1), showing that our strategy has potential advantages to fabricate low cost pH-sensing membranes. (C) 2012 Elsevier B.V. All rights reserved.

Enhancement of optical absorption by modulation of the oxygen flow of TiO2 films deposited by reactive sputtering

Oxygen-deficient TiO2 films with enhanced visible and near-infrared optical absorption have been deposited by reactive sputtering using a planar diode radio frequency magnetron configuration. It is observed that the increase in the absorption coefficient is more effective when the O-2 gas supply is periodically interrupted rather than by a decrease of the partial O-2 gas pressure in the deposition plasma. The optical absorption coefficient at 1.5 eV increases from about 1 x 10(2) cm(-1) to more than 4 x 10(3) cm(-1) as a result of the gas flow discontinuity. A red-shift of similar to 0.24 eV in the optical absorption edge is also observed. High resolution transmission electron microscopy with composition analysis shows that the films present a dense columnar morphology, with estimated mean column width of 40nm. Moreover, the interruptions of the O-2 gas flow do not produce detectable variations in the film composition along its growing direction. X-ray diffraction and micro-Raman experiments indicate the presence of the TiO2 anatase, rutile, and brookite phases. The anatase phase is dominant, with a slight increment of the rutile and brookite phases in films deposited under discontinued O-2 gas flow. The increase of optical absorption in the visible and near-infrared regions has been attributed to a high density of defects in the TiO2 films, which is consistent with density functional theory calculations that place oxygen-related vacancy states in the upper third of the optical bandgap. The electronic structure calculation results, along with the adopted deposition method and experimental data, have been used to propose a mechanism to explain the formation of the observed oxygen-related defects in TiO2 thin films. The observed increase in sub-bandgap absorption and the modeling of the corresponding changes in the electronic structure are potentially useful concerning the optimization of efficiency of the photocatalytic activity and the magnetic doping of TiO2 films. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4724334]

Neoproterozoic glacial deposits from the Aracuai orogen, Brazil: Age, provenance and correlations with the Sao Francisco craton and West Congo belt

Glacigenic diamictite successions of the Macaubas Group are widespread in the western domain of the Aracuai orogen, east of the Sao Francisco craton (Brazil). Diamictites also occur on this craton and in the African counterpart of the Aracuai orogen, the West Congo belt. Detrital zircon grains from the matrix of diamictites and sandstones from the Macaubas Group were dated by the U-Pb SHRIMP technique. The geochronological study sets the maximum depositional age of the glacial diamictites at 900 Ma, and indicates multiple sources for the Macaubas basin with ages ranging from 900 to 2800 Ma. Sm-Nd T-DM model ages, determined on whole rock samples, range from 1.8 Ga to 2.5 Ga and get older up-section. Comparison of our data with those from the cratonic area suggest that these glacial deposits can be correlated to the Jequitai and Carrancas diamictites in the Sao Francisco craton, and to the Lower Mixtite Formation of the West Congolian Group, exposed in Africa. The 900-1000 Ma source is most probably represented by the Zadinian-Mayumbian volcanic rocks and related granites from the West Congo belt. However, one of the most voluminous sources, with ages in the 1.1-1.3 Ga interval, has not been detected in the Sao Francisco-Congo craton. Possible sources for these grains could occur elsewhere in Africa, or possibly from within the Brasilia Belt in western central Brazil. (C) 2011 International Association for Gondwana Research. Published by Elsevier B.V. All rights reserved.

Influence of the Sol-Gel pH Process and Compact Film on the Efficiency of TiO2-Based Dye-Sensitized Solar Cells

The influence of pH during hydrolysis of titanium(IV) isopropoxide on the morphological and electronic properties of TiO2 nanoparticles prepared by the sol-gel method is investigated and correlated to the photoelectrochemical parameters of dye-sensitized solar cells (DSCs) based on TiO2 films. Nanoparticles prepared under acid pH exhibit smaller particle size and higher surface area, which result in higher dye loadings and better short-circuit current densities than DSCs based on alkaline TiO2-processed films. On the other hand, the product of charge collection and separation quantum yields in films with TiO2 obtained by alkaline hydrolysis is c. a. 27% higher than for the acid TiO2 films. The combination of acid and alkaline TiO2 nanoparticles as mesoporous layer in DSCs results in a synergic effect with overall efficiencies up to 6.3%, which is better than the results found for devices employing one of the nanoparticles separately. These distinct nanoparticles can be also combined by using the layer-by-layer technique (LbL) to prepare compact TiO2 films applied before the mesoporous layer. DSCs employing photoanodes with 30 TiO2 bilayers have shown efficiencies up to 12% higher than the nontreated photoanode ones. These results can be conveniently used to develop optimized synthetic procedures of TiO2 nanoparticles for several dye-sensitized solar cell applications.

Photoconduction action spectra of regio-regular poly(3-hexylthiopene):TiO2 diodes

The development of polymer-based photovoltaic devices brings the promise of low-cost and lightweight solar energy conversion systems. This technology requires new materials and device architectures with enhanced efficiency and lifetime, which depends on the understanding of charge-transport mechanisms. Organic films combined with electronegative nanoparticles may form systems with efficient dissociation of the photogenerated excitons, thus increasing the number of carriers to be collected by the electrodes. In this paper we investigate the steady-state photoconductive action spectra of devices formed by a bilayer of regio-regular poly(3-hexylthiophene) (RRP3HT) and TiO2 sandwiched between ITO and aluminum electrodes (ITO/TiO2:RRP3HT/Al). Photocurrents were measured for distinct bias voltages with illumination from either side of the device. Heterojunction structures were prepared by spin coating a RRP3HT film on an already deposited TiO2 layer on ITO. Symbatic and antibatic curves were obtained and a model for photocurrent action spectra was able to fit the symbatic responses. The quantum yield increased with the electric field, indicating that exciton dissociation is a field-assisted process as in an Onsager mechanism. Furthermore, the quantum yield was significantly higher when illumination was carried out through the ITO electrode onto which the TiO2 layer was deposited, as the highly electronegative TiO2 nanoparticles were efficient in exciton dissociation.

Rehabilitation with forage grasses of an area degraded by urban solid waste deposits

Dry matter yield and chemical composition of forage grasses harvested from an area degraded by urban solid waste deposits were evaluated. A split-plot scheme in a randomized block design with four replicates was used, with five grasses in the plots and three harvests in the subplots. The mineral content and extraction and heavy metal concentration were evaluated in the second cut, using a randomized block design with five grasses and four replicates. The grasses were Brachiaria decumbens cv. Basilisk, Brachiaria ruziziensis, Brachiaria brizantha cv. Marandu and cv. Xaraés, and Panicum maximum cv. Tanzânia, cut at 42 days of regrowth. The dry matter yield per cut reached 1,480 kg ha-1; the minimum crude protein content was 9.5% and the average neutral detergent fiber content was 62.3%. The dry matter yield of grasses was satisfactory, and may be an alternative for rehabilitating areas degraded by solid waste deposits. The concentration of heavy metals in the plants was below toxicity levels; the chemical composition was appropriate, except for phosphorus. The rehabilitated areas may therefore be used for grazing.

Currents controlling sedimentation, deposits recording palaeo-hydrodynamics – lessons from the continental shelf-slope system off SE South America

The continental margin off SE South America hosts one of the world’s most energetic hydrodynamic regimes but also the second largest drainage system of the continent. Both, the ocean current system as well as the fluvial runoff are strongly controlled by the atmospheric circulation modes over the region. The distribution pattern of particular types of sediments on shelf and slope and the long-term built-up of depositional elements within the overall margin architecture are, thus, the product of both, seasonal to millennial variability as well as long-term environmental trends. This talk presents how the combination of different methodological approaches can be used to obtain a comprehensive picture of the variability of a shelf and upper-slope hydrodynamic system during Holocene times. The particular methods applied are: (a) Margin-wide stratigraphic information to elucidate the role of sea level for the oceanographic and sedimentary systems since the last glacial maximum; (b) Palaeoceanographic sediment proxies combined with palaeo-temperature indicating isotopes of bivalve shells to trace lateral shifts in the coastal oceanography (particularly of the shelf front) during the Holocene; (c) Neodymium isotopes to identify the shelf sediment transport routes resulting from the current regime; (d) Sedimentological/geochemical data to show the efficient mechanism of sand export from the shelf to the open ocean; (e) Diatom assemblages and sediment element distributions indicating palaeo-salinity and the changing marine influence to illustrate the Plata runoff history. Sea level has not only controlled the overall configuration of the shelf but also the position of the main sediment routes from the continent towards the ocean. The shelf front has shifted frequently since the last glacial times probably resulting from both, changes in the Westerly Winds intensity and in the shelf width itself. Remarkable is a southward shift of this front during the past two centuries possibly related to anthropogenic influences on the atmosphere. The oceanographic regime with its prominent hydrographic boundaries led to a clear separation of sedimentary provinces since shelf drowning. It is especially the shelf front which enhances shelf sediment export through a continuous high sand supply to the uppermost slope. Finally, the Plata River does not continuously provide sediment to the shelf but shows significant climate-related changes in discharge during the past centuries. Starting from these findings, three major fields of research should, in general, be further developed in future: (i) The immediate interaction of the hydrodynamic and sedimentary systems to close the gaps between deposit information and modern oceanographic dynamics; (ii) Material budget calculations for the marginal ocean system in terms of material fluxes, storage/retention capacities, and critical thresholds; (iii) The role of human activity on the atmospheric, oceanographic and solid material systems to unravel natural vs. anthropogenic effects and feedback mechanisms