Performance and selectivity of PtxSn/C electro-catalysts for ethanol oxidation prepared by reduction with different formic acid concentrations

Carbon supported Pt-Sn catalysts were prepared by reduction of Pt and Sn precursors with formic acid and characterized in terms of structure, morphology and surface properties. The electrocatalytic activity for ethanol oxidation was studied in a direct ethanol fuel cell (DEFC) at 70 degrees C and 90 degrees C. Electrochemical and physico-chemical data indicated that a proper balance of Pt and Sn species in the near surface region was necessary to maximize the reaction rate. The best atomic surface composition, in terms of electrochemical performance, was Pt:Sn 65:35 corresponding to a bulk composition 75:25 namely Pt3Sn1/C. The reaction products of ethanol electro-oxidation in single cell and their distribution as a function of the nature of catalyst were determined. Essentially, acetaldehyde and acetic acid were detected as the main reaction products; whereas, a lower content of CO2 was formed. The selectivity toward acetic acid vs. acetaldehyde increased with the increase of the Sn content and decreased by decreasing the concentration of the reducing agent used in the catalyst preparation. According to the recent literature, these results have been interpreted on the basis of ethanol adsorption characteristics and ligand effects occurring for Sn-rich electrocatalysts. (C) 2012 Elsevier Ltd. All rights reserved.

The ethanol electrooxidation at Pt layers deposited on polycrystalline Au

The ethanol electro-oxidation reaction was evaluated using a polycrystalline Au substrate modified with two different amounts of Pt using the galvanic exchange methodology. FTIR results suggest that Pt deposits have a greater ability to break the C-C bond present in the ethanol molecule. However, under potentiostatic conditions both modified Au surfaces undergo faster deactivation in comparison with polycrystalline platinum as indicated by the chronoamperometric results. XPS results indicate the presence of two phases depending on the Pt content. These are: (i) Pt-Au alloy and (ii) segregated Pt. The structural and electronic properties of these phases were related to the differences observed in the catalytic activity.

Effects of the extraction conditions on the yield and composition of rice bran oil extracted with ethanol-A response surface approach

Rice bran oil was obtained from rice bran by solvent extraction using ethanol. The influence of process variables, solvent hydration (0-24% of water, on mass basis), temperature (60-90 degrees C), solvent-to-rice bran mass ratio (2.5:1 to 4.5:1) and stirrer speed (100-250 rpm) were analysed using the response surface methodology. The extraction yield was highly affected by the solvent water content, and it varied from 8.56 to 20.05 g of oil/100 g of fresh rice bran (or 42.7-99.9% of the total oil available) depending on the experimental conditions. It was observed that oryzanol and tocols behave in different ways during the extraction process. A larger amount of tocols is extracted from the solid matrix in relation to gamma-oryzanol. It was possible to obtain values from 123 to 271 mg of tocols/kg of fresh rice bran and 1527 to 4164 mg of oryzanol/kg of fresh rice bran, indicating that it is feasible to obtain enriched oil when this renewable solvent is used. No differences in the chemical composition of the extracted oils were observed when compared to the data cited in the literature. (C) 2011 The Institution of Chemical Engineers. Published by Elsevier B.V. All rights reserved.

Lipid biomarkers in surface sediments from an unusual coastal upwelling area from the SW Atlantic Ocean

The coastal upwelling off Cabo Frio (SE Brazilian coast, SEBC) represents an exception to the world`s oceans since the majority of the upwelling areas are located in eastern boundary current systems. Cabo Frio represents an interesting area for investigation due to its tight physical-biological interaction and the importance of the region as a major fishery area in the SEBC. We analyzed a suite of lipid biomarkers to apportion the main sources of organic matter in surface sediments of the continental shelf off Cabo Frio, comparing the area to non-upwelling regions off the SEBC (shelf break off Cabo Frio and continental shelf off Ubatuba). During spring and summer (the upwelling period), diatoms are probably the major sources of polyunsaturated fatty acids (PUFAs) and C-28 sterols in surface sediments from Cabo Frio continental shelf. Sediments sampled in winter showed, in contrast, lower relative abundance of PUFAs and higher stanol/stenol ratio values. In deeper regions off Cabo Frio, elevated concentrations of alkenones, 24-methylcholest-5,22E-dien-3 beta-ol and 24-ethylcholest-5-en-3 beta-ol during the spring may be produced by prymnesiophytes or cryptophytes and cyanobacteria, respectively. In Ubatuba, the C-27 and C-28 sterols are likely derived from omnivorous salps and nanoflagellates. At non-upwelling areas, despite the increase in biomarker concentrations during spring and summer, lower concentrations of PUFAs, phytol and algal sterols than in shelf areas off Cabo Frio suggest the importance of the upwelling system to the rapid transfer of organic carbon to surface sediments. Our results suggest that spatial and temporal variability in organic matter production and deposition merits consideration for constraining the carbon budgets in the coastal region off Cabo Frio. (C) 2008 Elsevier Ltd. All rights reserved.

Temporal changes in benthic megafaunal abundance and composition across the West Antarctic Peninsula shelf: Results from video surveys

The West Antarctic Peninsula (WAP) shelf experiences intense seasonal and interannual variability in phytoplankton production and particulate-organic-carbon flux to the seafloor. To explore the response of the megabenthic community to this production variability, we conducted video surveys of epibenthic megafauna at three stations on the WAP shelf in Nov-Dec 1999, Mar 2000, Jun 2000, Oct-Nov 2000, and Feb-Mar 2001. The epibenthic megafauna was dominated (>90%) by elasipod holothurians, irregular urchins and anthozoans, with total abundances ranging from 19 to 152 ind. 1 00 m(-2). The abundance of three of the dominant taxa (Protelpidia murrayi, Peniagone vignomi, and Amphipneustes spp.) varied significantly across seasons (p <0.05), although variations were not tightly correlated with the summer bloom cycle. The irregular urchins in the genus Amphipneustes varied 5-fold in abundance at single stations, with maximum densities (an average of 10.1 ind. 100 m(-2)) attained in Jun 2000. Abundances of the elasipod holothurians P. murrayi (1-121 ind. 100 m(-2)) and P. vignoni (0.7-27.5 ind. 100 m(-2)) fell within the range for elasipod holothurians from other bathyal regions measured using image analysis. The abundance of P. murrayi increased up to 6-fold from a single Jun-Oct recruitment pulse, while changes in the abundance of P. vignoni (over 2-fold higher in Feb-Mar 2001) apparently resulted from immigration during the presence of a 1-2 cm thick carpet of fresh phytocletritus. Based on the ratio of the number of fecal casts per individual, elasipod holothurians increased surface-deposit feeding rates by >= 2-fold while phytocletritus was present at the seafloor. Nonetheless, these surface-deposit feeders appeared to feed and egest sediments throughout the winter, which is consistent with year-round persistence of a labile food bank in surficial sediments on the deep WAP shelf.

Tailoring the structure, composition, optical properties and catalytic activity of Ag-Au nanoparticles by the galvanic replacement reaction

This Letter reports on the synthesis of Ag-Au nanoparticles (NPs) with controlled structures and compositions via a galvanic replacement reaction between Ag NPs and AuCl4(aq)- followed by the investigation of their optical and catalytic properties. Our results showed the formation of porous walls, hollow interiors and increased Au content in the Ag-Au NPs as the volume of AuCl4(aq)- employed in the reaction was increased. These variations led to a red shift and broadening of the SPR peaks and an increase of up to 10.9-folds in the catalytic activity towards the reduction of 4-nitrophenol relative to Ag NPs. (C) 2012 Elsevier B.V. All rights reserved.

Nanostructures on spin-coated polymer films controlled by solvent composition and polymer molecular weight

In this study we systematically investigated how the solvent composition used for polymer dissolution affects the porous structures of spin-coated polymers films. Cellulose acetate butyrate (CAB) and poly(methylmethacrylate) with low(PMMA-L) and high (PMMA-H) molecular weights were dissolved in mixtures of acetone (AC) and ethyl acetate (EA) at constant polymer concentration of 10 g/L The films were spin-coated at a relative air humidity of 55+/-5%, their thickness and index of refraction were determined by means of ellipsometry and their morphology was analyzed by atomic force microscopy. The dimensions and frequency of nanocavities on polymer films increased with the acetone content (phi(AC)) in the solvent mixture and decreased with increasing polymer molecular weight. Consequently, as the void content increased in the films, their apparent thicknesses increased and their indices of refraction decreased, creating low-cost anti-reflection surface. The void depth was larger for PMMA-L than for CAB. This effect was attributed to different activities of EA and AC in CAB or PMMA-L solution, the larger mobility of chains and the lower polarity of PMMA-L in comparison to CAB. (C) 2012 Elsevier B. V. All rights reserved.

Distribution of major elements in Atlantic surface sediments (36 degrees N-49 degrees S): Imprint of terrigenous input and continental weathering

Numerous studies use major element concentrations measured on continental margin sediments to reconstruct terrestrial climate variations. The choice and interpretation of climate proxies however differ from site to site. Here we map the concentrations of major elements (Ca, Fe, Al, Si, Ti, K) in Atlantic surface sediments (36 degrees N-49 degrees S) to assess the factors influencing the geochemistry of Atlantic hemipelagic sediments and the potential of elemental ratios to reconstruct different terrestrial climate regimes. High concentrations of terrigenous elements and low Ca concentrations along the African and South American margins reflect the dominance of terrigenous input in these regions. Single element concentrations and elemental ratios including Ca (e. g., Fe/Ca) are too sensitive to dilution effects (enhanced biological productivity, carbonate dissolution) to allow reliable reconstructions of terrestrial climate. Other elemental ratios reflect the composition of terrigenous material and mirror the climatic conditions within the continental catchment areas. The Atlantic distribution of Ti/Al supports its use as a proxy for eolian versus fluvial input in regions of dust deposition that are not affected by the input of mafic rock material. The spatial distributions of Al/Si and Fe/K reflect the relative input of intensively weathered material from humid regions versus slightly weathered particles from drier areas. High biogenic opal input however influences the Al/Si ratio. Fe/K is sensitive to the input of mafic material and the topography of Andean river drainage basins. Both ratios are suitable to reconstruct African and South American climatic zones characterized by different intensities of chemical weathering in well-understood environmental settings.

Histological composition and progression of carotid plaque

Abstract Background To analyse histological composition and progression of carotid plaque. Methods Thirty-one patients (22 males, mean age 68.03 ± 7.3 years) admitted for carotid endarterectomy for extracranial high-grade internal carotid artery stenosis (≥ 70% luminal narrowing) were enrolled. The patients were divided into 2 groups according to symptomatology (group I, 17 symptomatic patients; and group II, 14 asymptomatic patients). A histological analysis and inflammatory cell quantification of each excised carotid plaque was made. Nine carotid arteries were removed from human cadavers that were not preselected for carotid artery disease. These specimens were used as a control tissue without any macroscopic signs of atherosclerotic plaques. Results Fifty eight percent of all carotid plaques were classified as complex plaque with possible surface defect, hemorrhage or thrombus. The inflammatory cells concentration did not differ between the two groups. All specimens from human cadavers were classified as preatheroma with extracellular lipid pools. Conclusion Asymptomatic and symptomatic patients could have the same histological components on their carotid plaques. Fibrotic and calcific plaques could become vulnerable as complex plaques with surface defect, hemorrhage and thrombus could remain silent. Asymptomatic carotid stenosis should be followed close with no invasive diagnostic methods and clinical evaluation.

Effects of pretreatment on morphology, chemical composition and enzymatic digestibility of eucalyptus bark: a potentially valuable source of fermentable sugars for biofuel production – part 1

Abstract Background In recent years, the growing demand for biofuels has encouraged the search for different sources of underutilized lignocellulosic feedstocks that are available in sufficient abundance to be used for sustainable biofuel production. Much attention has been focused on biomass from grass. However, large amounts of timber residues such as eucalyptus bark are available and represent a potential source for conversion to bioethanol. In the present paper, we investigate the effects of a delignification process with increasing sodium hydroxide concentrations, preceded or not by diluted acid, on the bark of two eucalyptus clones: Eucalyptus grandis (EG) and the hybrid, E. grandis x urophylla (HGU). The enzymatic digestibility and total cellulose conversion were measured, along with the effect on the composition of the solid and the liquor fractions. Barks were also assessed using Fourier-transform infrared spectroscopy (FTIR), solid-state nuclear magnetic resonance (NMR), X-Ray diffraction, and scanning electron microscopy (SEM). Results Compositional analysis revealed an increase in the cellulose content, reaching around 81% and 76% of glucose for HGU and EG, respectively, using a two-step treatment with HCl 1%, followed by 4% NaOH. Lignin removal was 84% (HGU) and 79% (EG), while the hemicellulose removal was 95% and 97% for HGU and EG, respectively. However, when we applied a one-step treatment, with 4% NaOH, higher hydrolysis efficiencies were found after 48 h for both clones, reaching almost 100% for HGU and 80% for EG, in spite of the lower lignin and hemicellulose removal. Total cellulose conversion increased from 5% and 7% to around 65% for HGU and 59% for EG. NMR and FTIR provided important insight into the lignin and hemicellulose removal and SEM studies shed light on the cell-wall unstructuring after pretreatment and lignin migration and precipitation on the fibers surface, which explain the different hydrolysis rates found for the clones. Conclusion Our results show that the single step alkaline pretreatment improves the enzymatic digestibility of Eucalyptus bark. Furthermore, the chemical and physical methods combined in this study provide a better comprehension of the pretreatment effects on cell-wall and the factors that influence enzymatic digestibility of this forest residue.

Effects of chemical composition on the corrosion of dental alloys

The aim of this study was to determine the effect of the oral environment on the corrosion of dental alloys with different compositions, using electrochemical methods. The corrosion rates were obtained from the current-potential curves and electrochemical impedance spectroscopy (EIS). The effect of artificial saliva on the corrosion of dental alloys was dependent on alloy composition. Dissolution of the ions occurred in all tested dental alloys and the results were strongly dependent on the general alloy composition. Regarding the alloys containing nickel, the Ni-Cr and Ni-Cr-Ti alloys released 0.62 mg/L of Ni on average, while the Co-Cr dental alloy released ions between 0.01 and 0.03 mg/L of Co and Cr, respectively.The open-circuit potential stabilized at a higher level with lower deviation (standard deviation: Ni-Cr-6Ti = 32 mV/SCE and Co-Cr = 54 mV/SCE). The potenciodynamic curves of the dental alloys showed that the Ni-based dental alloy with >70 wt% of Ni had a similar curve and the Co-Cr dental alloy showed a low current density and hence a high resistance to corrosion compared with the Ni-based dental alloys. Some changes in microstructure were observed and this fact influenced the corrosion behavior for the alloys. The lower corrosion resistance also led to greater release of nickel ions to the medium. The quantity of Co ions released from the Co-Cr-Mo alloy was relatively small in the solutions. In addition, the quantity of Cr ions released into the artificial saliva from the Co-Cr alloy was lower than Cr release from the Ni-based dental alloys.

Variability in light absorption and scattering of phytoplankton in Patagonian waters: Role of community size structure and pigment composition

Intense phytoplankton blooms were observed along the Patagonian shelf-break with satellite ocean color data, but few in situ optical observations were made in that region. We examine the variability of phytoplankton absorption and particulate scattering coefficients during such blooms on the basis of field data. The chlorophyll-a concentration, [Chla], ranged from 0.1 to 22.3 mg m−3 in surface waters. The size fractionation of [Chla] showed that 80% of samples were dominated by nanophytoplankton (N-group) and 20% by microphytoplankton (M-group). Chlorophyll-specific phytoplankton absorption coefficients at 440 and 676 nm, a*ph(440) and a*ph(676), and particulate scattering coefficient at 660 nm, b*p(660), ranged from 0.018 to 0.173, 0.009 to 0.046, and 0.031 to 2.37 m2 (mg Chla)−1, respectively. Both a*ph(440) and a*ph(676) were statistically higher for the N-group than M-group and also considerably higher than expected from global trends as a function of [Chla]. This result suggests that size of phytoplankton cells in Patagonian waters tends to be smaller than in other regions at similar [Chla]. The phytoplankton cell size parameter, Sf, derived from phytoplankton absorption spectra, proved to be useful for interpreting the variability in the data around the general inverse dependence of a*ph(440), a*ph(676), and b*p(660) on [Chla]. Sf also showed a pattern along the increasing trend of a*ph(440) and a*ph(676) as a function of the ratios of some accessory pigments to [Chla]. Our results suggest that the variability in phytoplankton absorption and scattering coefficients in Patagonian waters is caused primarily by changes in the dominant phytoplankton cell size accompanied by covariation in the concentrations of accessory pigments.