Preparation and characterization of Zircaloy 4-Tantalum alloys for application in corrosive media

Two Zircaloy 4-Ta alloys (14 and 55 wt.% Ta) were produced by arc-melting. The alloys were hot-rolled at 900 degrees C and heat-treated under argon atmosphere for 100 h at 700 degrees C. The alloys were analyzed by scanning electron microscopy and X-ray diffractometry. The microstructure of both rolled and heat-treated alloys is constituted of (beta Zr,Ta)-II Ta-rich precipitates dispersed in a (alpha Zr) matrix. Corrosion tests performed in boiling concentrated H2SO4 solutions showed that the Zircaloy 4-Ta alloys are more corrosion resistant than Zircaloy 4 and that the corrosion resistance increases with increasing Ta content. (c) 2012 Elsevier Ltd. All rights reserved.

Occurrence and behavior of butyltins in intertidal and shallow subtidal surface sediments of an estuarine beach under different sampling conditions

Contamination by butyltin compounds (BTs) has been reported in estuarine environments worldwide, with serious impacts on the biota of these areas. Considering that BTs can be degraded by varying environmental conditions such as incident light and salinity, the short-term variations in such factors may lead to inaccurate estimates of BTs concentrations in nature. Therefore, the present study aimed to evaluate the possibility that measurements of BTs in estuarine sediments are influenced by different sampling conditions, including period of the day (day or night), tidal zone (intertidal or subtidal), and tides (high or low). The study area is located on the Brazilian southeastern coast, Sao Vicente Estuary, at Pescadores Beach, where BT contamination was previously detected. Three replicate samples of surface sediment were collected randomly in each combination of period of the day, tidal zone, and tide condition, from three subareas along the beach, totaling 72 samples. BTs were analyzed by GC-PFPD using a tin filter and a VF-5 column, by means of a validated method. The concentrations of tributyltin (TBT), dibutyltin (DBT), and monobutyltin (MBT) ranged from undetectable to 161 ng Sn g(-1) (d.w.). In most samples (71%), only MBT was quantifiable, whereas TBTs were measured in only 14, suggesting either an old contamination or rapid degradation processes. DBT was found in 27 samples, but could be quantified in only one. MBT concentrations did not differ significantly with time of day, zones, or tide conditions. DBT and TBT could not be compared under all these environmental conditions, because only a few samples were above the quantification limit. Pooled samples of TBT did not reveal any difference between day and night. These results indicated that, in assessing contamination by butyltin compounds, surface-sediment samples can be collected in any environmental conditions. However, the wide variation of BTs concentrations in the study area, i.e., over a very small geographic scale, illustrates the need for representative hierarchical and composite sampling designs that are compatible with the multiscalar temporal and spatial variability common to most marine systems. The use of such sampling designs will be necessary for future attempts to quantitatively evaluate and monitor the occurrence and impact of these compounds in nature

Preparation and characterization of poly(vinyl butyral)-polyaniline-montmorillonite nanocomposites

Poly(vinyl butyral)-polyaniline-sodium montmorillonite nanocomposites were prepared via polymerization of aniline between clay mineral platelets at two different pH levels (2.0 and 5.0), followed by dispersion of the polyaniline-sodium montmorillonite nanocomposite in a poly(vinyl butyral) solution. A comparison was made of the effect of the pH levels and the polyaniline-sodium montmorillonite nanocomposite precursor on the final structures of the poly(vinyl butyral) nanocomposites and their electrical conductivities. X-ray diffraction patterns revealed the formation of nanocomposites at both pH levels. UV-Vis spectra indicated that the polyaniline formed at both pH levels was conductive, with the UV-Vis spectra presenting a band at 420 nm corresponding to the polaronic form and the beginning of a new band at 600 nm indicating the presence of polaronic segments. FTIR spectra revealed the peaks of the groups present in polyaniline and poly(vinyl butyral) nanocomposites. The electrical conductivities of the polyaniline and poly(vinyl butyral) nanocomposites prepared at pH 2.0 were lower than those of the same nanocomposites prepared at pH 5.0, probably due to the lower formation of polyaniline chains in a more acidic dispersion and to the final configuration of polyaniline in the nanocomposites.

Influence of cueing on the preparation and execution of untrained and trained complex motor responses

This study investigated the influence of cueing on the performance of untrained and trained complex motor responses. Healthy adults responded to a visual target by performing four sequential movements (complex response) or a single movement (simple response) of their middle finger. A visual cue preceded the target by an interval of 300, 1000, or 2000 ms. In Experiment 1, the complex and simple responses were not previously trained. During the testing session, the complex response pattern varied on a trial-by-trial basis following the indication provided by the visual cue. In Experiment 2, the complex response and the simple response were extensively trained beforehand. During the testing session, the trained complex response pattern was performed in all trials. The latency of the untrained and trained complex responses decreased from the short to the medium and long cue-target intervals. The latency of the complex response was longer than that of the simple response, except in the case of the trained responses and the long cue-target interval. These results suggest that the preparation of untrained complex responses cannot be completed in advance, this being possible, however, for trained complex responses when enough time is available. The duration of the 1st submovement, 1st pause and 2nd submovement of the untrained and the trained complex responses increased from the short to the long cue-target interval, suggesting that there is an increase of online programming of the response possibly related to the degree of certainty about the moment of target appearance.

Stage, Grade and Behavior of Bladder Urothelial Carcinoma Defined by the MicroRNA Expression Profile

Purpose: We identified miRNA expression profiles in urothelial carcinoma that are associated with grade, stage, and recurrence-free and disease specific survival. Materials and Methods: The expression of 14 miRNAs was evaluated by quantitative reverse transcriptase-polymerase chain reaction in surgical specimens from 30 patients with low grade, noninvasive (pTa) and 30 with high grade, invasive (pT2-3) urothelial carcinoma. Controls were normal bladder tissue from 5 patients who underwent surgical treatment for benign prostatic hyperplasia. Endogenous controls were RNU-43 and RNU-48. miRNA profiles were compared and Kaplan-Meier curves were constructed to analyze disease-free and disease specific survival. Results: miR-100 was under expressed in 100% of low grade pTa specimens (p <0.001) and miR-10a was over expressed in 73.3% (p <0.001). miR-21 and miR-205 were over expressed in high grade pT2-3 disease (p = 0.02 and <0.001, respectively). The other miRNAs were present at levels similar to those of normal bladder tissue or under expressed in each tumor group. miR-21 over expression (greater than 1.08) was related to shorter disease-free survival in patients with low grade pTa urothelial carcinoma. Higher miR-10a levels (greater than 2.30) were associated with shorter disease-free and disease specific survival in patients with high grade pT2-3 urothelial carcinoma. Conclusions: Four miRNAs were differentially expressed in the 2 urothelial carcinoma groups. miR-100 and miR-10a showed under expression and over expression, respectively, in low grade pTa tumors. miR-21 and miR-205 were over expressed in pT2-3 disease. In addition, miR-10a and miR-21 over expression was associated with shorter disease-free and disease specific survival. miRNAs could be incorporated into the urothelial carcinoma molecular pathway. These miRNAs could also serve as new diagnostic or prognostic markers and new target drugs.

Preparation and characterization of chloroaluminum phthalocyanine-loaded solid lipid nanoparticles by thermal analysis and powder X-ray diffraction techniques

Solid lipid nanoparticles (SLN) without drug and SLN loaded with chloroaluminum phthalocyanine (AlClPc) were prepared by solvent diffusion method in aqueous system and characterized by thermal analyses and X-ray diffraction (XRD) in this study. Determination of particle size, zeta potential (ZP), and encapsulation efficiency were also evaluated. SLN containing AlClPc of nanometer size with high encapsulation efficiency and ZP were obtained. The results indicated that the size of SLN loaded with AlClPc is larger than that of the inert particle, but ZP is not changed significantly with incorporation of the drug. In differential scanning calorimetry (DSC) curves, it was observed that the melting point of stearic acid (SA) isolated and in SLN occurred at 55 and 64 degrees C, respectively, suggesting the presence of different polymorphs. DSC also shows that the crystallinity state of SLN was much less than that of SA isolated. The incorporation of drug in SLN may have been favored by this lower crystallinity degree of the samples. XRD techniques corroborated with the thermal analytic techniques, suggesting the polymorphic modifications of stearic acid.

Impact of maternal mild hyperglycemia on maternal care and offspring development and behavior of Wistar rats

The aim of the present study was to evaluate the effect of maternal mild hyperglycemia on maternal behavior, as well as the development, behavior, reproductive function, and glucose tolerance of the offspring. At birth, litters were assigned either to Control (subcutaneous (sc)-citrate buffer) or STZ groups (streptozotocin (STZ)-100 mg/kg-sc.). On PND 90 both STZ-treated and Control female rats were mated. Glucose tolerance tests (GTT) and insulin tolerance tests (ITT) were performed during pregnancy. Pregnancy duration, litter size and sex ratio were assessed. Newborns were classified according to birth weight as small (SPA), adequate (APA), or large for pregnancy age (LPA). Maternal behavior was analyzed on PND 5 and 10. Offspring body weight, length, and anogenital distance were measured and general activity was assessed in the open field. Sexual behavior was tested in both male and female offspring. Levels of reproductive hormones and estrous cycle duration were evaluated in female offspring. Female offspring were mated and both a GTT and ITT performed during pregnancy. Neonatal STZ administration caused mild hyperglycemia during pregnancy and changed some aspects of maternal care. The hyperglycemic intrauterine milieu impaired physical development and increased immobility in the open field in the offspring although the latter effect appeared at different ages for males (adulthood) and females (infancy). There was no impairment in the sexual behavior of either male or female offspring. As adults, female offspring of STZ-treated mothers did not show glucose intolerance during pregnancy. Thus, offspring of female rats that show mild hyperglycemia in pregnancy have fewer behavioral and developmental impairments than previously reported in the offspring of severely diabetic dams suggesting that the degree of impairment is directly related to the mother glycemic intensity. (C) 2012 Elsevier Inc. All rights reserved.

Assessment and management of oral health in liver transplant candidates

Liver transplantation has become a standard treatment for end-stage liver disease and the number of recipients has grown rapidly in the last few years. Dental care during pre-transplant workup is important to reduce potential sources of infection in the drug-induced immunosuppression phase of liver transplantation. Objectives: The objectives of this study were to document the prevalence of oral abnormalities in patients on a liver transplant waiting list presenting to an urban dental school clinic, discuss the appropriate dental treatment according their systemic conditions and compare their oral manifestations with those of healthy individuals. Material and Methods: A pilot study was conducted involving 16 end-stage liver disease individuals (study group- SG) attending the Special Care Dentistry Center of the University of So Paulo and 16 control individuals (control group- CG) with no liver diseases, receiving dental care at the Dental School of the University of So Paulo. These individuals were assessed for their dental status (presence of oral disease or abnormalities), coagulation status, and dental treatment indications. Results: The patients from SG exhibited a greater incidence of oral manifestations compared with CG (p=0.0327) and were diagnosed with at least one oral disease or condition that required treatment. Coagulation abnormalities reflecting an increased risk of bleeding were found in 93.75% of the patients. However, no bleeding complications occurred after dental treatment. Conclusions: The patients with chronic liver diseases evaluated in this study exhibited a higher incidence of oral manifestations compared with the control group and had at least one oral disease or abnormality which required dental treatment prior to liver transplantation. Careful oral examination and evaluation of the patient, including laboratory tests, will ensure correct oral preparation and control of oral disease prior to liver transplantation.

Persistent luminescence behavior of materials doped with Eu2+ and Tb3+

In this work, the persistent luminescence mechanisms of Tb3+ (in CdSiO3) and Eu2+ (in BaAl2O4) based on solid experimental data are compared. The photoluminescence spectroscopy shows the different nature of the inter- and intraconfigurational transitions for Eu2+ and Tb3+, respectively. The electron is the charge carrier in both mechanisms, implying the presence of electron acceptor defects. The preliminary structural analysis shows a free space in CdSiO3 able to accommodate interstitial oxide ions needed by charge compensation during the initial preparation. The subsequent annealing removes this oxide leaving behind an electron trap. Despite the low band gap energy for CdSiO3, determined with synchrotron radiation UV-VUV excitation spectroscopy of Tb3+, the persistent luminescence from Tb3+ is observed only with UV irradiation. The need of high excitation energy is due to the position of F-7(6) level deep below the bottom of the conduction band, as determined with the 4f(8)-> 4f(7)5d(1) and the ligand-to-metal charge-transfer transitions. Finally, the persistent luminescence mechanisms are constructed and, despite the differences, the mechanisms for Tb3+ and Eu2+ proved to be rather similar. This similarity confirms the solidity of the interpretation of experimental data for the Eu2+ doped persistent luminescence materials and encourages the use of similar models for other persistent luminescence materials. (C) 2012 Optical Society of America

Photo and electroluminescence behavior of Tb(ACAC)(3)phen complex used as emissive layer on organic light emitting diodes

This work shows the luminescence properties of a rare-earth organic complex, the Tb(ACAC)(3)phen. The results show the (5)D(4)->(7)F(3,4,5,6) transitions with no influence of the ligand. The photoluminescence excitation spectrum is tentatively interpreted by the ligands absorption. An organic light emitting diode (CLED) was made by thermal evaporation using TPD (N,N`-bis(3-methylphenyl)N,N`-diphenylbenzidine) and Alq3 (aluminum-tris(8-hydroxyquinoline)) as hole and electron transport layers, respectively. The emission reproduces the photoluminescence spectrum of the terbium complex at room temperature, with Commission Internationale de l`Eclairage - CIE (x,y) color coordinates of (0.28,0.55). No presence of any bands from the ligands was observed. The potential use of this compound in efficient devices is discussed. (C) 2008 Elsevier B.V. All rights reserved.

Behavior problems and prevalence of asthma symptoms among Brazilian children

Objective: Asthma is the most common chronic disease in childhood and has been designated a public health problem due to the increase in its prevalence in recent decades, the amount of health service expenditure it absorbs and an absence of consensus about its etiology. The relationships among psychosocial factors and the occurrence, symptomatology, and severity of asthma have recently been considered. There is still controversy about the association between asthma and a child`s mental health, since the pathways through which this relationship is established are complex and not well researched. This study aims to investigate whether behavior problems are associated with the prevalence of asthma symptoms in a large urban center in Latin America. Methods: It is a cross-section study of 869 children between 6 and 12 years old, residents of Salvador, Brazil. The International Study of Allergy and Asthma in Childhood (ISAAC) instrument was used to evaluate prevalence of asthma symptoms. The Child Behavior Checklist (CBCL) was employed to evaluate behavioral problems. Results: 19.26% (n = 212) of the children presented symptoms of asthma. 35% were classified as having clinical behavioral problems. Poisson`s robust regression model demonstrated a statistically significant association between the presence of behavioral problems and asthma symptoms occurrence (PR: 1.43; 95% Cl: 1.10-1.85). Conclusion: These results suggest an association between behavioral problems and pediatric asthma, and support the inclusion of mental health care in the provision of services for asthma morbidity. (C) 2011 Elsevier Inc. All rights reserved.

The influence of B4C and MgB2 additions on the behavior of MgO-C bricks

Carbon-containing refractory materials have received great attention over the last years due to their importance in the steelmaking process. The oxidation of carbon present in refractory materials at temperatures above 500 degrees C is usually accompanied by the decrease of their mechanical strength and chemical resistance. Aiming to improve the oxidation resistance of carbon-oxide refractories, the use of materials known as antioxidants has been extensively studied. In this work we evaluated the performance of MgB2 and B4C antioxidants when incorporated into MgO-C bricks. We observed that the co-addition of metallic antioxidants and B4C or MgB2 leads to refractory bricks with enhanced hot modulus of rupture and resistance against oxidation and slag corrosion. However, the excessive addition of these antioxidants could impair the performance of the obtained bricks. Thus, when determining the optimum concentration of MgB2 and B4C to be added into MgO-C refractories, one must take into consideration this behavior. (c) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Consumer attitudes, knowledge, and behavior related to salt consumption in sentinel countries of the Americas

Objective. To describe individual attitudes, knowledge, and behavior regarding salt intake, its dietary sources, and current food-labeling practices related to salt and sodium in five sentinel countries of the Americas. Methods. A convenience sample of 1 992 adults (>= 18 years old) from Argentina, Canada, Chile, Costa Rica, and Ecuador (approximately 400 from each country) was obtained between September 2010 and February 2011. Data collection was conducted in shopping malls or major commercial areas using a questionnaire containing 33 questions. Descriptive estimates are presented for the total sample and stratified by country and sociodemographic characteristics of the studied population. Results. Almost 90% of participants associated excess intake of salt with the occurrence of adverse health conditions, more than 60% indicated they were trying to reduce their current intake of salt, and more than 30% believed reducing dietary salt to be of high importance. Only 26% of participants claimed to know the existence of a recommended maximum value of salt or sodium intake and 47% of them stated they knew the content of salt in food items. More than 80% of participants said that they would like food labeling to indicate high, medium, and low levels of salt or sodium and would like to see a clear warning label on packages of foods high in salt. Conclusions. Additional effort is required to increase consumers' knowledge about the existence of a maximum limit for intake and to improve their capacity to accurately monitor and reduce their personal salt consumption.

Chemical evaluation and thermal behavior of Brazil nut oil obtained by different extraction processes

Brazil nut richness has been widely studied aiming at finding transformation models that increase its yield, keep its quality, reduce costs, and increase its productivity. The objective of this study is to evaluate the spectroscopic profile and the chemical and thermal behavior of Brazil nut oil obtained by different extraction processes. Lipid soxhlet extractions with petroleum ether and hexane, and using hydraulic pressing and supercritical carbon dioxide (CO2) were performed. The physicochemical analyses showed an acidity index with significant differences between the samples obtained by hydraulic pressing and supercritical CO2. The peroxide index presented significant difference for the oil obtained by hydraulic pressing compared to that obtained by the other extraction processes. The fatty acid profiles showed a relevant presence of the omega series (w-3, w-6, and w-9) with significant differences for the extraction processes evaluated. The results of the thermogravimetric and differential analyses did not indicate changes in mass loss and presented predominantly exothermic behavior. The spectroscopic profiles indicate that the extraction processes do not change the spectral profile of the oils. (c) 2011 Elsevier Ltd. All rights reserved.

Optomechanical trans-to-cis and cis-to-trans isomerization and unusual photophysical behavior of fac-[Re(CO)(3)(phen)(CNstpy)](+)

Unusual high photoassisted quantum yields for cis-to-trans (phi(254) (nm) = 0.27 +/- 0.05) isomerization of CNstpy coordinated to fac-[Re(CO)(3)(phen)(CNstpy)](+) were determined along with trans-to-cis ones (phi(313) (nm)= 0.58 +/- 0.02; phi(365) (nm)= 0.61 +/- 0.06; phi(404) (nm) = 0.42 +/- 0.02). Additionally, in contrast to other similar rhenium(I) complexes, the cis photoproduct is quasi non-emissive and comparable to the trans-complex. The cis-to-trans photoisomerization is due to the deactivation from the ILcis-CNstpy excited state in competition to the usual (MLCTRe -> phen)-M-3 luminescence. These efficient cis to trans and trans to cis photoisomerization can be conveniently used in light powered molecular machines. (C) 2012 Elsevier B.V. All rights reserved.