Stoichiometry, structure, and transport in the quasi-one-dimensional metal Li0.9Mo6O17

A correlation between lattice parameters, oxygen composition, and the thermoelectric and Hall coefficients is presented for single-crystal Li0.9Mo6O17, a quasi-one-dimensional (Q1D) metallic compound. The possibility that this compound is a compensated metal is discussed in light of a substantial variability observed in the literature for these transport coefficients.

Superconductivity and magnetism in the KxMoO2-delta

Coexistence between superconductivity and magnetism is reported for the KxMoO2-delta samples. Photoemission experiments show that the presence of Mo3+ ions is responsible for the weak ferromagnetic ordering observed in the KxMoO2-delta samples. Magnetic ordering temperature and superconducting critical temperature (T-C) ratio range from 7 to 18 in this compound. These are the highest ratios reported so far for a magnetic superconductor. T-C decreases with increasing potassium composition (x). For the first time, T-C near 10 K is reported in the K-Mo-O system. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4757003]

Adubação mineral com cobalto e molibdênio na cultura da soja

Altas produtividades de soja requerem grandes quantidades de nitrogênio, que podem ser obtidas principalmente, a partir da fixação simbiótica. No entanto, há possibilidade da eficiência desse processo biológico ser prejudicada pela deficiência de micronutrientes, especialmente de cobalto e molibdênio. Nesse contexto, objetivou-se com o presente trabalho avaliar a eficiência agronômica e a forma de aplicação de adubação mineral com cobalto e molibdênio na cultura da soja. Para tanto, a cultivar CD-206 foi submetida a diferentes tratamentos que consistiram da combinação entre aplicação de Co e Mo via tratamento de sementes e adubação foliar. As características agronômicas avaliadas foram o número de nódulos, massa seca da parte aérea, massa seca de raiz, número de vagens, número de grãos, massa de mil grãos e produção de grãos. A aplicação de molibdênio e cobalto via sementes e/ ou adubação foliar no estádio V4 (terceira folha trifoliolada completamente desenvolvida, quarto nó) promoveram incrementos significativos no rendimento da cultura. Respostas positivas ao cobalto e molibdênio também foram observadas no número de nódulos, vagens e grãos, com aumentos de até 240 kg ha-1 no rendimento da cultura. Os parâmetros agronômicos avaliados foram afetados positivamente pela aplicação de Co e Mo, principalmente quanto aplicado tanto via semente como foliar (TS + V4), inclusive para a produtividade de grãos. A forma de aplicação não foi significativamente distinta, ou seja, tanto a aplicação via semente como via foliar foram eficientes no fornecimento destes nutrientes para a cultura da soja.

Effect of denture cleansers on metal ion release and surface roughness of denture base materials

Chemical disinfectants are usually associated with mechanical methods to remove stains and reduce biofilm formation. This study evaluated the effect of disinfectants on release of metal ions and surface roughness of commercially pure titanium, metal alloys, and heat-polymerized acrylic resin, simulating 180 immersion trials. Disk-shaped specimens were fabricated with commercially pure titanium (Tritan), nickel-chromium-molybdenum-titanium (Vi-Star), nickel-chromium (Fit Cast-SB Plus), and nickel-chromium-beryllium (Fit Cast-V) alloys. Each cast disk was invested in the flasks, incorporating the metal disk to the heat-polymerized acrylic resin. The specimens (n=5) were immersed in these solutions: sodium hypochlorite 0.05%, Periogard, Cepacol, Corega Tabs, Medical Interporous, and Polident. Deionized water was used as a control. The quantitative analysis of metal ion release was performed using inductively coupled plasma mass spectrometry (ELAN DRC II). A surface analyzer (Surftest SJ-201P) was used to measure the surface roughness (µm). Data were recorded before and after the immersions and evaluated by two-way ANOVA and Tukey's test (α=0.05). The nickel release proved most significant with the Vi-Star and Fit Cast-V alloys after immersion in Medical Interporous. There was a significant difference in surface roughness of the resin (p=0.011) after immersion. Cepacol caused significantly higher resin roughness. The immersion products had no influence on metal roughness (p=0.388). It could be concluded that the tested alloys can be considered safe for removable denture fabrication, but disinfectant solutions as Cepacol and Medical Interporous tablet for daily denture immersion should be used with caution because it caused greater resin surface roughness and greater ion release, respectively.