Constrained least square pre-distortion scheme for multiuser ultra-wideband

The study proposes a constrained least square (CLS) pre-distortion scheme for multiple-input single-output (MISO) multiple access ultra-wideband (UWB) systems. In such a scheme, a simple objective function is defined, which can be efficiently solved by a gradient-based algorithm. For the performance evaluation, scenarios CM1 and CM3 of the IEEE 802.15.3a channel model are considered. Results show that the CLS algorithm has a fast convergence and a good trade-off between intersymbol interference (ISI) and multiple access interference (MAI) reduction and signal-to-noise ratio (SNR) preservation, performing better than time-reversal (TR) pre-distortion.

Experimental Investigation of the Hydrodynamic Coefficients of a Remotely Operated Vehicle Using a Planar Motion Mechanism

The determination of hydrodynamic coefficients of full scale underwater vehicles using system identification (SI) is an extremely powerful technique. The procedure is based on experimental runs and on the analysis of on-board sensors and thrusters signals. The technique is cost effective and it has high repeatability; however, for open-frame underwater vehicles, it lacks accuracy due to the sensors' noise and the poor modeling of thruster-hull and thruster-thruster interaction effects. In this work, forced oscillation tests were undertaken with a full scale open-frame underwater vehicle. These conducted tests are unique in the sense that there are not many examples in the literature taking advantage of a PMM installation for testing a prototype and; consequently, allowing the comparison between the experimental results and the ones estimated by parameter identification. The Morison's equation inertia and drag coefficients were estimated with two parameter identification methods, that is, the weighted and the ordinary least-squares procedures. It was verified that the in-line force estimated from Morison's equation agrees well with the measured one except in the region around the motion inversion points. On the other hand, the error analysis showed that the ordinary least-squares provided better accuracy and, therefore, was used to evaluate the ratio between inertia and drag forces for a range of Keulegan-Carpenter and Reynolds numbers. It was concluded that, although both experimental and estimation techniques proved to be powerful tools for evaluation of an open-frame underwater vehicle's hydrodynamic coefficients, the research provided a rich amount of reference data for comparison with reduced models as well as for dynamic motion simulation of ROVs. [DOI: 10.1115/1.4004952]

Ligand- and Structure-Based Drug Design Strategies and PPAR delta/alpha Selectivity

Peroxisome-proliferator-activated receptors are a class of nuclear receptors with three subtypes: a, ? and d. Their main function is regulating gene transcription related to lipid and carbohydrate metabolism. Currently, there are no peroxisome-proliferator-activated receptors d drugs being marketed. In this work, we studied a data set of 70 compounds with a and d activity. Three partial least square models were created, and molecular docking studies were performed to understand the main reasons for peroxisome-proliferator-activated receptors d selectivity. The obtained results showed that some molecular descriptors (log P, hydration energy, steric and polar properties) are related to the main interactions that can direct ligands to a particular peroxisome-proliferator-activated receptors subtype.

Utility Harmonic Impedance Measurement Based on Data Selection

Determination of the utility harmonic impedance based on measurements is a significant task for utility power-quality improvement and management. Compared to those well-established, accurate invasive methods, the noninvasive methods are more desirable since they work with natural variations of the loads connected to the point of common coupling (PCC), so that no intentional disturbance is needed. However, the accuracy of these methods has to be improved. In this context, this paper first points out that the critical problem of the noninvasive methods is how to select the measurements that can be used with confidence for utility harmonic impedance calculation. Then, this paper presents a new measurement technique which is based on the complex data-based least-square regression, combined with two techniques of data selection. Simulation and field test results show that the proposed noninvasive method is practical and robust so that it can be used with confidence to determine the utility harmonic impedances.

Análise de fatores associados ao significado do trabalho

O trabalho tem sido visto não somente como forma de obter a renda, mas também como atividade que proporciona realização pessoal, status social e possibilidade de estabelecer e manter contatos interpessoais, entre outros. Nesta pesquisa, teve-se como objetivo investigar os fatores que influenciam e conferem sentido ao trabalho, como centralidade do trabalho, normas da sociedade e objetivos e resultados valorizados. Na centralidade do trabalho, procurou-se investigar o grau de importância do trabalho dentro do contexto das diversas áreas da vida das pessoas, como família, lazer, religião e vida comunitária. Em normas da sociedade, foram analisados os pontos mais significativos no tocante ao que a sociedade deveria proporcionar ao indivíduo, assim como o que o indivíduo deveria fazer em prol da sociedade. Nos objetivos e resultados valorizados, foi pesquisado o que as pessoas buscam com o trabalho. A partir da pesquisa na literatura, foi elaborado um modelo inicial que, não se mostrando satisfatório segundo critérios estatísticos, foi substituído por outro que apresentou significância estatística e boa aderência aos dados. O modelo escolhido foi o que melhor goodness-of-fit apresentou, quando se utilizou modelagem de equações estruturais pelo método partial least square. O estudo revelou que o significado do trabalho se reflete, na ordem, na centralidade do trabalho, nos objetivos e resultados valorizados e, por último, nas normas sociais.

Emprego de ferramentas numéricas na avaliação do módulo de elasticidade em vigas roliças de madeira

Vigas são elementos estruturais encontrados na maioria das construções civis. Dentre os materiais de engenharia, destaca-se a madeira, por ter resistência mecânica satisfatória aliada a baixa densidade. A madeira roliça apresenta-se como boa solução na confecção de vigas, uma vez que não precisa ser processada, como é o caso da madeira serrada. O projeto de elementos estruturais de madeira requer o conhecimento de suas propriedades físicas e mecânicas, obtidas segundo as premissas de documentos normativos. Em se tratando da madeira roliça, os documentos normativos nacionais que tratam da determinação das propriedades de resistência e rigidez estão vigentes há mais de vinte anos sem revisão técnica. De forma geral, tanto as normas nacionais como as internacionais idealizam geometria troncocônica para as peças roliças de madeira, implicando equações simplificadas incapazes de prever a influência das irregularidades da forma na determinação do módulo de elasticidade longitudinal. Este trabalho objetiva avaliar a influência das irregularidades da geometria em peças roliças de madeira Corymbia citriodora e Pinus caribaea no cálculo do módulo de elasticidade longitudinal. Para tanto, utilizou-se do ensaio de flexão estática a três pontos, considerando também um modelo matemático simplificado, assumindo seção circular constante para a forma do elemento. As irregularidades das peças são consideradas nos modelos numéricos, constituídos de elementos finitos de barra e tridimensionais. Os resultados encontrados revelam equivalência estatística entre os módulos de elasticidade para ambas as formas de cálculo, indicando ser plausível a consideração de seção circular constante para as peças de madeira aqui avaliadas.

Fatores de influência no preço do milho no Brasil

Compreender a dinâmica de funcionamento do mercado de milho brasileiro, procedendo a uma investigação dos fatores que afetam as quantidades e preços nesse mercado, é o objetivo deste trabalho. Os testes de raiz unitária foram feitos utilizando-se a metodologia DF-GLS - Dickey Fuller Generalized Least Square - e os de cointegração de Johansen (1988). O modelo estimado, de ajuste pelo preço, foi um Modelo de Autorregressão Vetorial com Correção de Erros - VEC, sendo a identificação feita pelo procedimento de Sims-Bernanke. O estudo permite afirmar que existe forte interação entre os mercados de milho e de soja, mostrando uma relação de complementaridade na oferta e substitutibilidade na demanda, e que fatores macroeconômicos como renda e juros são importantes na determinação dos preços do milho ao produtor e no atacado. Vale ressaltar que os preços externos do milho mostraram relativa importância no processo de formação do preço doméstico do grão.

Lipid and glucose profiles of dairy buffaloes during lactation and dry period

The purpose of this study was to analyze the influence of lactation and dry period in the constituents of lipid and glucose metabolism of buffaloes. One hundred forty-seven samples of serum and plasma were collected between November 2009 and July 2010, from properties raising Murrah, Mediterranean and crossbred buffaloes, located in the State of Sao Paulo, Brazil. Biochemical analysis was obtained by determining the contents of serum cholesterol, triglycerides, beta-hydroxybutyrate (β-HBO), non-esterified fatty acids (NEFA) and plasma glucose. Values for arithmetic mean and standard error mean were calculated using the SAS procedure, version 9.2. Tests for normality of residuals and homogeneity of variances were performed using the SAS Guide Data Analysis. Data were analyzed by ANOVA using the SAS procedure Glimmix. The group information (Lactation), Farm and Age were used in the statistical models. Means of groups were compared using Least Square Means (LSMeans) of SAS, where significant difference was observed at P ≤ 0.05. It was possible to conclude that buffaloes during peak lactation need to metabolize body reserves to supplement the lower amounts of bloodstream lipids, when they remain in negative energy balance. In the dry period, there were significant changes in the lipid profile, characterized by decrease of nutritional requirements, with consequent improvement in the general conditions of the animals.

A study of the anti-plasmodium activity of angiotensin II analogs

Controlling the dissemination of malaria requires the development of new drugs against its etiological agent, a protozoan of the Plasmodium genus. Angiotensin II and its analog peptides exhibit activity against the development of immature and mature sporozoites of Plasmodium gallinaceum. In this study, we report the synthesis and characterization of angiotensin II linear and cyclic analogs with anti-plasmodium activity. The peptides were synthesized by a conventional solid-phase method on Merrifield's resin using the t-Boc strategy, purified by RP-HPLC and characterized by liquid chromatography/ESI (+) MS (LC-ESI(+)/MS), amino acid analysis, and capillary electrophoresis. Anti-plasmodium activity was measured in vitro by fluorescence microscopy using propidium iodine uptake as an indicator of cellular damage. The activities of the linear and cyclic peptides are not significantly different (p < 0.05). Kinetics studies indicate that the effects of these peptides on plasmodium viability overtime exhibit a sigmoidal profile and that the system stabilizes after a period of 1 h for all peptides examined. The results were rationalized by partial least-square analysis, assessing the position-wise contribution of each amino acid. The highest contribution of polar amino acids and a Lys residue proximal to the C-terminus, as well as that of hydrophobic amino acids in the N-terminus, suggests that the mechanism underlying the anti-malarial activity of these peptides is attributed to its amphiphilic character.

Sedentary behaviours and its association with bone mass in adolescents: the HELENA cross-sectional study

Background: We aimed to examine whether time spent on different sedentary behaviours is associated with bone mineral content (BMC) in adolescents, after controlling for relevant confounders such as lean mass and objectively measured physical activity (PA), and if so, whether extra-curricular participation in osteogenic sports could have a role in this association. Methods: Participants were 359 Spanish adolescents (12.5-17.5 yr, 178 boys,) from the HELENA-CSS (2006-07). Relationships of sedentary behaviours with bone variables were analysed by linear regression. The prevalence of low BMC (at least 1SD below the mean) and time spent on sedentary behaviours according to extracurricular sport participation was analysed by Chi-square tests. Results: In boys, the use of internet for non-study was negatively associated with whole body BMC after adjustment for lean mass and moderate to vigorous PA (MVPA). In girls, the time spent studying was negatively associated with femoral neck BMC. Additional adjustment for lean mass slightly reduced the negative association between time spent studying and femoral neck BMC. The additional adjustment for MVPA did not change the results at this site. The percentage of girls having low femoral neck BMC was significantly smaller in those participating in osteogenic sports (>= 3 h/week) than in the rest, independently of the cut-off selected for the time spent studying. Conclusions: The use of internet for non-study (in boys) and the time spent studying (in girls) are negatively associated with whole body and femoral neck BMC, respectively. In addition, at least 3 h/week of extra-curricular osteogenic sports may help to counteract the negative association of time spent studying on bone health in girls.

Soil compressibility and least limiting water range of a constructed soil under cover crops after coal mining in Southern Brazil

The use of cover crops affects the support capacity of soil and least limiting water range to crop growth. The objective of this study was to quantify preconsolidation pressure (sigma(p)), compression index (CI) and least limiting water range (LLWR) of a reclaimed coal mining soil under different cover crops, in Candiota, RS, Brazil. In the experiment, with randomized blocks design and four replicates, the following cover crops (treatments) were evaluated: Hemarthria altissima (Poir.) Stapf & C.E. Hubbard, treatment 1 (T1), Paspalum notatum Flugge, treatment 4 (T4), Cynodon dactilon (L) Pers., treatment 5 (T5), control Brachiaria brizantha (Hochst.) Stapf, treatment 7 (T7) and without cover crop treatment 8 (reference treatment, T8). Soil compression and least limiting water range were evaluated with undisturbed samples at a depth of 0.00-0.05 m. In order to evaluate parameters of soil compressibility, the soil samples were saturated with water and subjected to -10 kPa matric potential and then submitted to a uniaxial compression test under the following pressures: 25, 50, 100, 200, 400, 800 and 1600 kPa. Cover crops decreased the preconsolidation pressure of constructed soils after coal mining and the greatest soil reclamation was obtained with the H. altissima cover crop, where the lowest degree of soil compactness and soil load capacity were observed. Soils cultivated under H. altissima or B. brizantha presented the highest least limiting water range and these two cover crops generated similar soil critical bulk density obtained by least limiting water range and soil load support capacity. (C) 2012 Elsevier B.V. All rights reserved.

Two versions of the threshold contact model in two dimensions

Two versions of the threshold contact process ordinary and conservative - are studied on a square lattice. In the first, particles are created on active sites, those having at least two nearest neighbor sites occupied, and are annihilated spontaneously. In the conservative version, a particle jumps from its site to an active site. Mean-field analysis suggests the existence of a first-order phase transition, which is confirmed by Monte Carlo simulations. In the thermodynamic limit, the two versions are found to give the same results. (C) 2012 Elsevier B.V. All rights reserved.

Men's health: a population-based study on social inequalities

This study evaluates social inequalities in health according to level of schooling in the male population. This was a cross-sectional, population-based study with a sample of 449 men ranging from 20 to 59 years of age and living in Campinas, Sao Paulo State, Brazil. The chi-square test was used to verify associations, and a Poisson regression model was used to estimate crude and adjusted prevalence ratios. Men with less schooling showed higher rates of alcohol consumption and dependence, smoking, sedentary lifestyle during leisure time, and less healthy eating habits, in addition to higher prevalence of bad or very bad self-rated health, at least one chronic disease, hypertension, and other health problems. No differences were detected between the two schooling strata in terms of use of health services, except for dental services. The findings point to social inequality in health-related behaviors and in some health status indicators. However, possible equity was observed in the use of nearly all types of health services.

Topography of four different endodontic rotary systems, before and after being used for the 12th time

Root canal preparation may damage NiTi instruments resulting in wear and deformation. The aim of this study was to make a comparative evaluation of the surface topography of the cervical third of four different rotary systems, before and after being used twelve times, in 1.440 resin blocks with simulated root canals with standardized 45 degrees curvatures, and analyzed by atomic force microscopy AFM. The blocks were divided into four groups and prepared according to the manufacturers recommendations: Group 1 - K3 (R); Group 2 - Protaper Universal (R); Group 3 - Twisted Files (R) and Group 4 - Biorace (R). After each preparation, the instruments were washed and autoclaved. A total of 240 instruments were selected, being 30 new instruments and 30 after having been used for the 12th time, from each group. These instruments were analyzed by AFM and for quantitative evaluation, the mean RMS (Root mean square) values of the cervical third of the specimens from the four groups were used. The result showed that all the rotary files used for the 12th time suffered wear with change in the topography of the cervical region of the active portion of the file (ANOVA p < 0.01). Classifying the specimens in increasing order, from the least to the greatest wear suffered, Group 3 (2.8993 nm) presented the least wear, followed by Group 4 (12.2520 nm), Group 1 (36.0043 nm) and lastly, Group 2 (59.8750 nm) with the largest amount of cervical surface wear. Microsc. Res. Tech. 75:97-102, 2012. (c) 2011 Wiley Periodicals, Inc.

Comparison of multiple-input single-output single-user ultra-wideband systems with pre-distortion

This paper presents a performance analysis of a baseband multiple-input single-output ultra-wideband system over scenarios CM1 and CM3 of the IEEE 802.15.3a channel model, incorporating four different schemes of pre-distortion: time reversal, zero-forcing pre-equaliser, constrained least squares pre-equaliser, and minimum mean square error pre-equaliser. For the third case, a simple solution based on the steepest-descent (gradient) algorithm is adopted and compared with theoretical results. The channel estimations at the transmitter are assumed to be truncated and noisy. Results show that the constrained least squares algorithm has a good trade-off between intersymbol interference reduction and signal-to-noise ratio preservation, providing a performance comparable to the minimum mean square error method but with lower computational complexity. Copyright (C) 2011 John Wiley & Sons, Ltd.