Analysis of the Dielectric Behavior of Distribution Insulators Under Non-Standard Lightning Impulses Voltages

Overhead distribution lines are often exposed to lightning overvoltages, whose waveforms vary widely and can differ substantially from the standard impulse voltage waveform (1,2 - 50). Different models have been proposed for predicting the strength of insulation subjected to impulses of non-standard waveforms. One of the most commonly used is the disruptive effect model, for which there are different methods for the estimation of the parameters required for its application. This paper aims at evaluating the dielectric behavior of medium voltage insulators subjected to impulses of non-standard waveforms, as well as at evaluating two methods for predicting their dielectric strength against such impulses. The test results relative to the critical lightning impulse flashover voltage (U50) and the volt-time characteristics obtained for the positive and negative polarities of different voltage waveforms are presented and discussed.

Can Indian Ocean SST anomalies influence South American rainfall?

In this study we examine the impact of Indian Ocean sea surface temperature (SST) variability on South American circulation using observations and a suite of numerical experiments forced by a combination of Indian and Pacific SST anomalies. Previous studies have shown that the Indian Ocean Dipole (IOD) mode can affect climate over remote regions across the globe, including over South America. Here we show that such a link exists not only with the IOD, but also with the Indian Ocean basin-wide warming (IOBW). The IOBW, a response to El Nino events, tends to reinforce the South American anomalous circulation in March-to-May associated with the warm events in the Pacific. This leads to increased rainfall in the La Plata basin and decreased rainfall over the northern regions of the continent. In addition, the IOBW is suggested to be an important factor for modulating the persistence of dry conditions over northeastern South America during austral autumn. The link between the IOBW and South American climate occurs via alterations of the Walker circulation pattern and through a mid-latitude wave-train teleconnection.

Grain size effect on the structural and dielectric properties of Pb0.85La0.15TiO3 ferroelectric ceramic compound

This paper presents a study of the influence of particle size on the structural and dielectric properties of Pb0.85La0.15TiO3 (PLT15) ferroelectric ceramic samples. The samples were prepared with average grain size of 1.69 +/- 0.08 mu m and 146 +/- 8 nm using, respectively, conventional and spark plasma sintering techniques. A decrease in the tetragonality degree as the crystallite size decreased was explained by an internal stress caused by the existence of a large amount of grain boundaries. The local structure exhibited no significant modification and the dielectric measurements showed a diffuse phase transition and a reduction in the permittivity magnitude at T-m as the average grain size decreased. The nanostructured ceramic sample prepared at a relatively lower temperature and sintering time presented a dielectric constant value of approximately 2000 at room temperature. (c) 2012 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Correlating phase and microstructure development versus dielectric properties in La3+ and Er3+ co-doped Bi4Ti3O12 ferroelectric ceramics

Bi3.25La0.75-xErxTi3O12 and Bi3.25La0.75Ti3-xErxO12-delta ceramics were prepared and studied in this work in terms of dopant-induced phase and microstructure development as well as dielectric response. The results show that introduction of Er3+ tends to reduce the materials' sintering temperature and average grain size. Moreover, it was noted that in these systems the substitution site of this dopant is controlled by valence state and ionic radii mismatch effects. In particular, even when a nominal substitution of Ti4+ is conceived, here it is found that Er3+ also incorporates at the (Bi,La)(3+) sites. These and other interesting concluding remarks from this work, including Er3+ tolerance, were possible only after comparing, especially, the X-ray diffraction results and the intrinsic ferroelectric characteristics extracted from the dielectric measurements. (C) 2011 Elsevier B.V. All rights reserved.

Structural refinement, optical and microwave dielectric properties of BaZrO3

In this work, barium zirconate (BaZrO3) ceramics synthesized by solid state reaction method and sintered at 1670 degrees C for 4 h were characterized by X-ray diffraction (XRD), Rietveld refinement, and Fourier transform infrared (FT-IR) spectroscopy. XRD patterns, Rietveld refinement data and FT-IR spectra which confirmed that BaZrO3 ceramics have a perovskite-type cubic structure. Optical properties were investigated by ultraviolet-visible (UV-vis) absorption and photoluminescence (PL) measurements. UV-vis absorption spectra suggested an indirect allowed transition with the existence of intermediary energy levels within the band gap. Intense visible green PL emission was observed in BaZrO3 ceramics upon excitation with a 350 nm wavelength. This behavior is due to a majority of deep defects within the band gap caused by symmetry breaking in octahedral [ZrO6] clusters in the lattice. The microwave dielectric constant and quality factor were measured using the method proposed by Hakki-Coleman. The dielectric resonator antenna (DRA) was investigated experimentally and numerically using a monopole antenna through an infinite ground plane and Ansoft's high frequency structure simulator software, respectively. The required resonance frequency and bandwidth of DRA were investigated by adjusting the dimension of the same material. (C) 2011 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Cytogenomic characterization of an unexpected 17.6 Mb 9p deletion associated to a 14.8 Mb 20p duplication in a dysmorphic patient with multiple congenital anomalies presenting a normal G-banding karyotype

We describe a female patient with developmental delay, dysmorphic features and multiple congenital anomalies who presented a normal G-banded karyotype at the 550-band resolution. Array and multiplex-ligation probe amplification (MLPA) techniques identified an unexpected large unbalanced genomic aberration: a 17.6 Mb deletion of 9p associated to a 14.8 Mb duplication of 20p. The deleted 9p genes, especially CER1 and FREM1, seem to be more relevant to the phenotype than the duplicated 20p genes. This study also shows the relevance of using molecular techniques to make an accurate diagnosis in patients with dysmorphic features and multiple anomalies suggestive of chromosome aberration, even if on G-banding their karyotype appears to be normal. Fluorescence in situ hybridization (FISH) was necessary to identify a masked balanced translocation in the patient's mother, indicating the importance of associating cytogenetic and molecular techniques in clinical genetics, given the implications for patient management and genetic counseling. (C) 2012 Elsevier B.V. All rights reserved.

Rehabilitative treatment of cleft lip and palate: experience of the Hospital for Rehabilitation of Craniofacial Anomalies - USP (HRAC-USP) - Part 2: Pediatric Dentistry and Orthodontics

The aim of this article is to present the pediatric dentistry and orthodontic treatment protocol of rehabilitation of cleft lip and palate patients performed at the Hospital for Rehabilitation of Craniofacial Anomalies - University of So Paulo (HRAC-USP). Pediatric dentistry provides oral health information and should be able to follow the child with cleft lip and palate since the first months of life until establishment of the mixed dentition, craniofacial growth and dentition development. Orthodontic intervention starts in the mixed dentition, at 8-9 years of age, for preparing the maxillary arch for secondary bone graft procedure (SBGP). At this stage, rapid maxillary expansion is performed and a fixed palatal retainer is delivered before SBGP. When the permanent dentition is completed, comprehensive orthodontic treatment is initiated aiming tooth alignment and space closure. Maxillary permanent canines are commonly moved mesially in order to substitute absent maxillary lateral incisors. Patients with complete cleft lip and palate and poor midface growth will require orthognatic surgery for reaching adequate anteroposterior interarch relationship and good facial esthetics.

Rehabilitative treatment of cleft lip and palate: experience of the Hospital for Rehabilitation of Craniofacial Anomalies - USP (HRAC-USP) - Part 3: Oral and Maxillofacial Surgery

This paper presents the treatment protocol of maxillofacial surgery in the rehabilitation process of cleft lip and palate patients adopted at HRAC-USP. Maxillofacial surgeons are responsible for the accomplishment of two main procedures, alveolar bone graft surgery and orthognathic surgery. The primary objective of alveolar bone graft is to provide bone tissue for the cleft site and then allow orthodontic movements for the establishment of an an adequate occlusion. When performed before the eruption of the maxillary permanent canine, it presents high rates of success. Orthognathic surgery aims at correcting maxillomandibular discrepancies, especially anteroposterior maxillary deficiencies, commonly observed in cleft lip and palate patients, for the achievement of a functional occlusion combined with a balanced face.

Rehabilitative treatment of cleft lip and palate: experience of the Hospital for Rehabilitation of Craniofacial Anomalies/USP (HRAC/USP) - Part 1: overall aspects

C left lip and palate is the most common among craniofacial malformations and causes several esthetic and functional implications that require rehabilitation. This paper aims to generally describe the several aspects related to this complex pathology and the treatment protocol used by the Hospital for Rehabilitation of Craniofacial Anomalies, University of So Paulo (HRAC-USP) along 40 years of experience in the treatment of individuals with cleft lip and palate.

Dental anomalies in Richieri-Costa-Pereira syndrome

Objective. The objective of this study was to investigate the prevalence of dental anomalies in individuals with Richieri-Costa-Pereira syndrome. Study Design. A total of 13 individuals with Richieri-Costa-Pereira syndrome who were older than 8 years with at least 1 available panoramic radiograph were assessed. Dental anomalies were evaluated clinically and radiographically and classified as hyperplastic, hypoplastic, or heterotopic and as alterations of shape, number, position, and structure. Enamel alterations were classified by the DDE index. Results. All individuals exhibited anomalies, with predominance of hypoplastic disorders, mainly agenesis of mandibular incisors and second premolars and demarcated creamy-white enamel opacities primarily affecting the maxillary premolars. Conclusions. Individuals with Richieri-Costa Pereira syndrome exhibit high prevalence of tooth agenesis, especially mandibular incisors and premolars, as well as high frequency of enamel opacities. These findings are compatible with the mandibular cleft observed in all individuals and also reflect the hypoplastic characteristic of the syndrome. (Oral Surg Oral Med Oral Pathol Oral Radiol 2012;114:99-106)

Frontonasal dysplasia, callosal agenesis, basal encephalocele, and eye anomalies syndrome with a partial 21q22.3 deletion

We describe a girl with a phenotype characterized by frontonasal dysplasia, callosal agenesis, basal encephalocele, and eye anomalies who presents a 46,XX,r(21) karyotype. Array-comparative genomic hybridization using the Afflymetrix 100K DNA oligoarray set showed an interstitial deletion 21q22.3 of approximately 219?kb. Conventional karyotype of both parents was normal, and it was not possible to perform the molecular studies. In this report we raise the hypothesis that the deleted genes located at 21q22.3 could account to the phenotype. (C) 2012 Wiley Periodicals, Inc.

Influence of Molecular Dynamics on the Dielectric Properties of Poly(9,9-di-n-octylfluorene-alt-benzothiadiazole) -Based Devices

This paper uses Nuclear Magnetic Resonance (NMR) and Differential Scanning Calorimetry (DSC) techniques to study the molecular relaxations and phase transitions in poly(9,9-di-n-octylfluorene-alt-benzothiadiazole) (F8BT), which has been extensively studied as the active thin film in organic devices. Besides the identification of the glass transition, beta relaxation and crystal-to-crystal phase transition, we correlate such phenomena with dielectric and transport mechanisms in diodes with F8BT as the active layer. The beta relaxation has been assigned to a transition at about 210 K measured by H-1 and C-13 solid state NMR, and can be attributed to local motions in the side chains. The glass transition has been detected by DSC and H-1 NMR. Dielectric spectroscopy (DS) carried out at low frequencies on diodes made from F8BT show two peaks which are coincident with the above transitions. This allowed us to correlate the electrical changes in the film with the onset of specific molecular motions. In addition, DS indicates a third peak related with a crystal-to-crystal phase transition. Finally, these transitions were correlated with changes in the carrier mobility recorded in thin films and published recently.

Bulk neutrinos as an alternative cause of the gallium and reactor anti-neutrino anomalies

We consider an alternative explanation for the deficit of nu(e) in Ga solar neutrino calibration experiments and of the (nu) over bar (e) in short-baseline reactor experiments by a model where neutrinos can oscillate into sterile Kaluza-Klein modes that can propagate in compactified submicrometer flat extra dimensions. We have analyzed the results of the gallium radioactive source experiments and 19 reactor experiments with baseline shorter than 100 m, and showed that these data can be fit into this scenario. The values of the lightest neutrino mass and of the size of the largest extra dimension that are compatible with these experiments are mostly not excluded by other neutrino oscillation experiments.

Developmental and Epigenetic Anomalies in Cloned Cattle

Many of the developmental anomalies observed in cloned animals are related to foetal and placental overgrowth, a phenomenon known as the 'large offspring syndrome' (LOS) in ruminants. It has been hypothesized that the epigenetic control of imprinted genes, that is, genes that are expressed in a parental-specific manner, is at the root of LOS. Our recent research has focused on understanding epigenetic alterations to imprinted genes that are associated with assisted reproductive technologies (ART), such as early embryo in vitro culture (IVC) and somatic cell nuclear transfer (SCNT) in cattle. We have sought and identified single nucleotide polymorphisms in Bos indicus DNA useful for the analysis of parental-specific alleles and their respective transcripts in tissues from hybrid embryos derived by crossing Bos indicus and Bos taurus cattle. By analysing differentially methylated regions (DMRs) of imprinted genes SNRPN, H19 and the IGF2R in cattle, we demonstrated that there is a generalized hypomethylation of the imprinted allele and the biallelic expression of embryos produced by SCNT when compared to the methylation patterns observed in vivo (artificially inseminated). Together, these results indicate that imprinting marks are erased during the reprogramming of the somatic cell nucleus during early development, indicating that such epigenetic anomalies may play a key role in mortality and morbidity of cloned animals.

Effects of moisture content on structural and dielectric properties of cassava starch films

In this work, it was evaluated the effect of moisture content on the structural and dielectric properties of cassava starch films by means of Fourier Transform infrared spectroscopy (FTIR), impedancimetric, and gravimetric analysis. The film samples were equilibrated in hermetically sealed desiccators, containing different saturated salts in water in order to promote activity of water between 0.11 and 0.85. The position and amplitude of the peaks in the fingerprint region of the FTIR spectra were changed due to the modifications in the interactions between the polymeric chains and water molecules. These effects may be related to the formation of semi-crystalline regions in the film structure. The dielectric properties of the films were also strongly dependent on the moisture content, showing a non-linear and a linear region, which was attributed to the domain of bound and free water in the film, respectively. The gravimetric analyzes showed the typical sigmoidal behavior, attributed to the way the water interacts with the biopolymer. Finally, the flexibility of the films increased with water content increasing.