Predicting the behaviour of structures under impact loads using geometrically distorted scaled models

When a scaled structure (model or replica) is used to predict the response of a full-size compound (prototype), the model geometric dimensions should relate to the corresponding prototype dimensions by a single scaling factor. However, owing to manufacturing technical restrictions, this condition cannot be accomplished for some of the dimensions in real structures. Accordingly, the distorted geometry will not comply with the overall geometric scaling factor, infringing the Pi theorem requirements for complete dynamic similarity. In the present study, a method which takes geometrical distortions into account is introduced, leading to a model similar to the prototype. As a means to infer the performance of this method, three analytical problems of structures subjected to dynamic loads are analysed. It is shown that the replica developed applying this technique is able to accurately predict the full-size structure behaviour even when the studied models have some of their dimensions severely distorted. (C) 2012 Elsevier Ltd. All rights reserved.

Analysis of elastic functionally graded materials under large displacements via high-order tetrahedral elements

The purpose of this study is to present a position based tetrahedral finite element method of any order to accurately predict the mechanical behavior of solids constituted by functionally graded elastic materials and subjected to large displacements. The application of high-order elements makes it possible to overcome the volumetric and shear locking that appears in usual homogeneous isotropic situations or even in non-homogeneous cases developing small or large displacements. The use of parallel processing to improve the computational efficiency, allows employing high-order elements instead of low-order ones with reduced integration techniques or strain enhancements. The Green-Lagrange strain is adopted and the constitutive relation is the functionally graded Saint Venant-Kirchhoff law. The equilibrium is achieved by the minimum total potential energy principle. Examples of large displacement problems are presented and results confirm the locking free behavior of high-order elements for non-homogeneous materials. (C) 2011 Elsevier B.V. All rights reserved.

Are the preference and selection patterns of hermit crabs for gastropod shells species- or site-specific?

Experimental analyses of hermit crabs and their preferences for shells are essential to understand the intrinsic relationship of the crabs` dependence on shells, and may be useful to explain their shell use pattern in nature. The aim of this study was to evaluate the effect of crab species and site on the pattern of shell use, selection, and preference in the south-western Atlantic hermit crabs Pagurus brevidactylus and Pagurus criniticornis, comparing sympatric and allopatric populations. Differently from the traditional approach to evaluate shell preference by simply determining the shell selection pattern (i.e., the number of shells of each type selected), preference was defined (according to [Liszka, D., Underwood, AJ., 1990. An experimental design to determine preferences for gastropod shells by a hermit-crab. J. Exp. Mar. Biol. Ecol., 137(1), 47-62]) by the comparison of the number of crabs changing for a particular shell type when three options were given (Cerithium atratum, Morula nodulosa, and Tegula viridula) with the number of crabs changing for this same type when only this type was offered. The effect of crab species was tested at Cabelo Gordo Beach, where P. brevidacrylus was found occupying shells of C. atratum, M. nodulosa, and T viridula in similar frequencies, whereas P. criniticornis occupied predominantly shells of C atratum. In laboratory experiments the selection patterns of the two hermit-crab species for these three gastropods were different, with P criniticornis selecting mainly shells of C atratum, and R brevidactylus selecting more shells of M. nodulosa. The shell preference was also dependent on crab species, with P. criniticornis showing a clear preference for shells of C atratum, whereas P. brevidactylus did not show a preference for any of the tested shells. The effect of site was tested for the two species comparing data from Cabelo Gordo to Preta (P brevidactylus) and Araca beaches (P. criniticornis). The pattern of shell use, selection, and preference was demonstrated to be dependent on site only for P. brevidactylus. The results also showed that the shell use pattern of P criniticornis can be explained by its preference at both sites, whereas for P. brevidactylus it occurred only at Cabelo Gordo, where the absence of preference was correlated with the similar use of the three gastropod species studied. Finally, the results showed that the shell selection pattern cannot be considered as a measure of shell preference, since it overestimates crab selectivity. (C) 2009 Elsevier B.V. All rights reserved.

Mechanical Performance of Cylindrical and Dual-Core Pedicle Screws After Repeated Insertion

Study Design. Ex vivo study of the mechanical performance of cylindrical and dual-core pedicle screws after insertion, removal, and reinsertion in the same hole. Objective. To evaluate the effect of repeated use of same screw hole on the insertion torque and the retentive strength of the cylindrical and dual-core screws. Summary of Background Data. Insertion and removal of pedicle screws is sometimes necessary during surgical procedure to assess the integrity of the pilot-hole wall. However, this maneuver may compromise the implant-holding capacity. Methods. Sixty thoracolombar vertebrae (T13-L5), harvested from 10 healthy calves, were used to insert 2 different designs of pedicle screws: cylindrical (5.0-mm outer diameter) and dual-core screws (5.2-mm outer diameter). Three experimental groups were created on the basis of the number of insertions of the screws and 2 subgroups were established according to the core pedicle screw design (dual-core and cylindrical). The insertion torque was measured during initial insertion, second insertion, and third insertion. Pullout screw tests were performed using a universal testing machine to evaluate the pullout strength after initial insertion, second insertion, and third insertion. Results. Significant reductions of 38% in mean insertion torque and 30% in mean pullout strength of dual-core screw were observed between the initial insertion and the third insertion. The cylindrical screw observed significant reductions of 52.5% in mean insertion torque and 42.3% in mean pullout strength between the initial insertion and the third insertion. A reduction of mean insertion torque and pullout strength between the first insertion and the second insertion but without significance was also observed for both types of screws. Conclusion. Insertions and reinsertion of either cylindrical or dual-core pedicle screws have compromised insertion torque and pullout strength of the implants as measured by mechanical tests.