Influence of the deposition parameters on the morphology and electrical conductivity of PANI/PSS self-assembled films

The influence of deposition parameters, namely polymer concentration and pH of the deposition solution, cleaning, and drying steps on the morphology and electrical characteristics of polyaniline and sulfonated polystyrene (PANI/PSS) nanostructured films deposited by the self-assembly technique is evaluated by UV-Vis spectroscopy, optical and atomic force microscopy, and electrical resistance measurements. It is found that stirring the cleaning solution during the cleaning step is crucial for obtaining homogenous films. Stirring of the cleaning solution also influences the amount of PANI adsorbed in the films. In this regard, the drying process seems to be less critical since PANI amount and film thickness are similar in films dried with N-2 flow or with an absorbent tissue. It is observed, however, that drying with N-2 flow results in rougher films. As an additional point, an assessment of the influence of the deposition method (manual versus mechanical) on the film characteristics was carried out. A significant difference on the amount of PANI and film thickness between films prepared by different human operators and by a homemade mechanical device was observed. The variability in film thickness and PANI adsorbed amount is smaller in films mechanically assembled. (c) 2007 Elsevier B.V. All rights reserved.

Influenza A/H1N1 vaccination of patients with SLE: can antimalarial drugs restore diminished response under immunosuppressive therapy?

Objective. To assess the efficacy and safety of pandemic 2009 influenza A (H1N1) in SLE under different therapeutic regimens. Methods. A total of 555 SLE patients and 170 healthy controls were vaccinated with a single dose of a non-adjuvanted preparation. According to current therapy, patients were initially classified as SLE No Therapy (n = 75) and SLE with Therapy (n = 480). Subsequent evaluations included groups under monotherapy: chloroquine (CQ) (n = 105), prednisone (PRED) epsilon 20 mg (n = 76), immunosuppressor (IS) (n = 95) and those with a combination of these drugs. Anti-H1N1 titres and seroconversion (SC) rate were evaluated at entry and 21 days post-vaccination. Results. The SLE with Therapy group had lower SC compared with healthy controls (59.0 vs 80.0%; P < 0.0001), whereas the SLE No Therapy group had equivalent SC (72 vs 80.0%; P = 0.18) compared with healthy controls. Further comparison revealed that the SC of SLE No Therapy (72%) was similar to the CQ group (69.5%; P = 0.75), but it was significantly reduced in PRED epsilon 20 mg (53.9%; P = 0.028), IS (55.7%; P = 0.035) and PRED epsilon 20 mg + IS (45.4%; P = 0.038). The concomitant use of CQ in each of these later regimens was associated with SC responses comparable with SLE No Therapy group (72%): PRED epsilon 20 mg + CQ (71.4%; P = 1.00), IS + CQ (65.2%; P = 0.54) and PRED epsilon 20 mg + IS + CQ (57.4%; P = 0.09). Conclusion. Pandemic influenza A H1N1/2009 vaccine response is diminished in SLE under immunosuppressive therapy and antimalarials seems to restore this immunogenicity.

Micro-mechanical bond strength tests for the assessment of the adhesion of GIC to dentine

Background. The aim of this study is to critically evaluate the bond strength (BS) of Glass-Ionomer Cements (GIC) to dentine with microtensile (mu TBS) and microshear (mu SBS) BS tests by assessing their rankings and failure patterns. Methods. Samples were made on flat dentine surfaces and submitted to mTBS and mSBS. The materials used were: high viscosity GIC (Ketac (TM) Molar Aplicap-KM), resin-modified GIC (Fuji II-FII), nano-filled resin-modified GIC (Ketac (TM) N100-N100) and an etch-and-rinse adhesive system with a composite resin (Adper (TM) Single Bond 2 and Z100 (TM)-Z100). All tests were performed with a Universal Testing Machine (24 h water storage, crosshead speed of 1 mm/min). Debonded surfaces were examined with a stereomicroscope (x40) to identify the failure mode. The data was analyzed with two-way ANOVA (p < 0.05) and LSD test. Results. Means were statistically different regarding the tests and materials, indicating that values for BS obtained for each material depend on the test performed. Failure analysis revealed that failures produced by mTBS were mainly cohesive for KM and FII. mu SBS failures were mainly adhesive or mixed for all materials. For the mTBS, the rank was Z100 > FII > KM = N100, whereas for the mSBS it was Z100 = FII = KM > N100. Conclusion: It may be concluded that distinct micro-mechanical tests present different failure patterns and rankings depending on the material to be considered.

Numerical study of Mach number and thermal effects on sound radiation by a mixing layer

Mach number and thermal effects on the mechanisms of sound generation and propagation are investigated in spatially evolving two-dimensional isothermal and non-isothermal mixing layers at Mach number ranging from 0.2 to 0.4 and Reynolds number of 400. A characteristic-based formulation is used to solve by direct numerical simulation the compressible Navier-Stokes equations using high-order schemes. The radiated sound is directly computed in a domain that includes both the near-field aerodynamic source region and the far-field sound propagation. In the isothermal mixing layer, Mach number effects may be identified in the acoustic field through an increase of the directivity associated with the non-compactness of the acoustic sources. Baroclinic instability effects may be recognized in the non-isothermal mixing layer, as the presence of counter-rotating vorticity layers, the resulting acoustic sources being found less efficient. An analysis based on the acoustic analogy shows that the directivity increase with the Mach number can be associated with the emergence of density fluctuations of weak amplitude but very efficient in terms of noise generation at shallow angle. This influence, combined with convection and refraction effects, is found to shape the acoustic wavefront pattern depending on the Mach number.

Immediate and long-term effects of polysaccharides-based formulations on human skin

A new trend in cosmetic formulations is the use of biotechnological raw materials as the polysaccharides from Klebsiella pneumoniae, which are supposed to enhance cell renewal, improve skin hydration and micro-relief. Botanical extracts of Myrtus communis leaves contain different sugars, which may provide the same benefits. Thus, the objective of this study was to evaluate through objective and subjective analysis the immediate and long-term effects of cosmetic formulations containing polysaccharides biotechnologically-originated and / or the ones contained in Myrtus communis extracts. Three polysaccharide-based and placebo formulations were applied on the forearm skin of 40 volunteers. Skin hydration, transepidermal water loss (TEWL), viscoelasticity and skin micro-relief measurements were made before and 2 hours after a single application and after 15 and 30 day-periods of daily applications. Answers to a questionnaire about perceptions of formulation cosmetic features constituted the subjective analysis. All polysaccharide-based formulations enhanced skin hydration. Formulations with isolated or combined active substances improved skin barrier function as compared to placebo, in the short and long term studies. Formulations containing Myrtus communis extracts had the highest acceptance. Results suggest that daily use of formulations containing these substances is important for protection of the skin barrier function.

Development of Plurimetallic Electrocatalysts Prepared by Decomposition of Polymeric Precursors for EtOH/O-2 Fuel Cell

This work aimed to develop plurimetallic electrocatalysts composed of Pt, Ru, Ni, and Sn supported on C by decomposition of polymeric precursors (DPP), at a constant metal: carbon ratio of 40:60 wt.%, for application in direct ethanol fuel cell (DEFC). The obtained nanoparticles were physico-chemically characterized by X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX). XRD results revealed a face-centered cubic crystalline Pt with evidence that Ni, Ru, and Sn atoms were incorporated into the Pt structure. Electrochemical characterization of the nanoparticles was accomplished by cyclic voltammetry (CV) and chronoamperometry (CA) in slightly acidic medium (0.05 mol L-1 H2SO4), in the absence and presence of ethanol. Addition of Sn to PtRuNi/C catalysts significantly shifted the ethanol and CO onset potentials toward lower values, thus increasing the catalytic activity, especially for the quaternary composition Pt64Sn15Ru13Ni8/C. Electrolysis of ethanol solutions at 0.4 V vs. RHE allowed determination of acetaldehyde and acetic acid as the main reaction products. The presence of Ru in alloys promoted formation of acetic acid as the main product of ethanol oxidation. The Pt64Sn15Ru13Ni8/C catalyst displayed the best performance for DEFC.

Water use in a sugarcane plantation

The evapotranspiration (E) from a sugarcane plantation in the southeast Brazil was measured by the eddy-covariance method during two consecutive cycles. These represented the second (393 similar to days) and third year (374 similar to days) re-growth (ratoon). The total E in the first cycle was 829 similar to mm, accounting for 69% of rainfall, whereas in the second cycle, it was 690 similar to mm, despite the total rainfall (1353 similar to mm) being 13% greater. The ratio of E to available energy, the evaporative fraction, exhibited a smaller variation between the first and second cycles: 0.58 and 0.51, respectively. The estimated interception losses were 88 and 90 similar to mm, respectively, accounting for approximately 7% of the total rainfall. The sugarcane yield in the second cycle (61.5 similar to +/-similar to 4.0 similar to t similar to ha-1) was 26% lower than the first cycle, as well as lower than the regional average for the third ratoon (76 similar to t similar to ha-1). The below average yield was associated with less available soil water at the beginning of the cycle, with the amount of rainfall recorded during the first 120 similar to days of re-growth in the second cycle being 16% of that recorded in the first (203 similar to mm).

Relationships between gender, age, family conditions, physical and mental health, and social isolation of elderly caregivers

Background: In an aging population an increasing number of elderly caregivers will be called upon to provide care over a long period, during which time they will be burdened both by caregiving and by the physiological effects of their own aging. Among them there will be more aged male caregivers, who will probably be less prepared than women to become caregivers. The aim of this study was to investigate the relationship between caregivers' gender, age, family income, living arrangements and social support as independent variables, and depressive symptoms, comorbidities, level of frailty, grip strength, walking speed and social isolation, as dependent variables. Methods: 176 elderly people (123 women) were selected from a sample of a population-based study on frailty (n = 900), who had cared for a spouse (79.3%) and/or parents (31.4%) in the past five years (mean age = 71.8 +/- 4.86 years; mean monthly family income in minimum wages = 4.64 +/- 5.14). The study used questionnaires and self-report scales, grip strength and walking speed tests. Results: 65% of participants evaluated caregiving as being very stressful. Univariate analyses of regression showed low family income as a risk factor for depression; being female and low perceived social support as a risk for comorbidities; being 80 years of age and above for low grip strength; and being male for social isolation indicated by discontinuity of activities and social roles. In multivariate analyses of regression, poverty arose as a risk factor for depression and being female for comorbidities. Conclusions: Gender roles, age, income and social support interacted with physical and emotional health, and with the continuity of social participation of elderly caregivers. Special attention must be given to male caregivers.

COMMUNITY OF ORIGIN EFFECTS ON VIRTUAL BRAND COMMUNITIES PARTICIPANT

The question about the effectiveness of companies in maintaining their own communities versus benefiting from the ones owned by consumers remains open. We examine differences between firm-managed and customer-managed brand communities regarding the impact of perceived psychographic homogeneity, availability of virtual avenues and relationship with the brand on the community's influence on members and the assessments and intentions of community participants. Data were obtained from 555 respondents in two leading Microsoft XBOX brand communities in Brazil. Results indicate that management of the community of origin is the moderator of all considered relationships. Also, the most favorable effects for the company occur in the community that is not directly controlled and managed by the company itself. Brand loyalty, however, is higher for members of the official brand community. Guidelines on how companies can benefit from consumer-managed communities are discussed.

Signal transduction in Plasmodium-Red Blood Cells interactions and in cytoadherence

Malaria is responsible for more than 1.5 million deaths each year, especially among children (Snow et al. 2005). Despite of the severity of malaria situation and great effort to the development of new drug targets (Yuan et al. 2011) there is still a relative low investment toward antimalarial drugs. Briefly there are targets classes of antimalarial drugs currently being tested including: kinases, proteases, ion channel of GPCR, nuclear receptor, among others (Gamo et al. 2010). Here we review malaria signal transduction pathways in Red Blood Cells (RBC) as well as infected RBCs and endothelial cells interactions, namely cytoadherence. The last process is thought to play an important role in the pathogenesis of severe malaria. The molecules displayed on the surface of both infected erythrocytes (IE) and vascular endothelial cells (EC) exert themselves as important mediators in cytoadherence, in that they not only induce structural and metabolic changes on both sides, but also trigger multiple signal transduction processes, leading to alteration of gene expression, with the balance between positive and negative regulation determining endothelial pathology during a malaria infection.

Efeitos da comunidade de origem no participante de comunidades virtuais de marca

Os benefícios das empresas em manterem comunidades virtuais de marca próprias versus os provenientes das comunidades criadas pelos consumidores permanecem desconhecidos. Esse estudo testa o efeito moderador do tipo de gestão da comunidade no impacto da homogeneidade psicográfica percebida, da disponibilidade de avenidas virtuais e do relacionamento com a marca sobre as influências da comunidade e as intenções dos participantes da comunidade. Os dados provêm de 555 participantes ativos de duas grandes comunidades virtuais para o game XBOX no Brasil. Os resultados comprovam que a gestão da comunidade de origem é moderadora de todas as relações consideradas. Apontam, também, que alguns dos efeitos mais favoráveis para a empresa ocorrem na comunidade gerida pelos consumidores. A lealdade à marca, porém, é maior para membros da comunidade oficial. O estudo indica como as empresas podem se beneficiar de comunidades geridas por consumidores.

Temporary effect of chiseling on the compaction of a Rhodic Hapludox under no-tillage

Mechanical chiseling has been used to alleviate the effects of compaction in soils under no-tillage (NT). However, its effect on the soil physical properties does not seem to have a defined duration period. The purpose of this study was to evaluate the behavior of the bulk density (BD) and degree of compaction (DC) at different soil depths, after chiseling in no-tillage, for one year. The experiment was performed in Ponta Grossa, Paraná State, Brazil, using an Oxisol (Rhodic Hapludox). Bulk density and DC were previously measured in an area under NT for 16 years, then immediately after chiseling (CHI) in May 2009, six months after chiseling (CHI6M) in October 2009 and one year after chiseling (CHI12M) in May 2010. In the layers 0.0-0.10, 0.10-0.20 and 0.20-0.30 m, there was a significant BD reduction CHI and a marked increase CHI6M. The BD values measured CHI12M were similar to those before tillage. Chiseling reduced the DC in the layers 0.0-0.10 m and 0.10-0.20 m, but returned to the initial values one year later. During the evaluation periods CHI, CHI6M and CHI12M, the BD increased in the layer 0.30-0.40 m, compared with NT. The highest DC values were observed six months after chiseling; nevertheless the structural recovery of the soil was considerable, possibly due to the high degree of soil resilience and the influence of the wetting and drying cycles detected in the study period. The chiseling effects, evaluated by BD and DC, lasted less than one year, i.e., the beneficial short-term effects of chiseling on the reduction of the surface BD increased the risk of compaction in deeper soil layers.

Diversity and genetic structure in natural populations of Hancornia speciosa var. speciosa Gomes in northeastern Brazil

Hancornia speciosa Gomes is a fruit tree native from Brazil that belongs to Apocinaceae family, and is popularly known as Mangabeira. Its fruits are widely consumed raw or processed as fruit jam, juices and ice creams, which have made it a target of intense exploitation. The extractive activities and intense human activity on the environment of natural occurrence of H. speciosa has caused genetic erosion in the species and little is known about the ecology or genetic structure of natural populations. The objective of this research was the evaluation of the genetic diversity and genetic structure of H. speciosa var. speciosa. The genetic variability was assessed using 11 allozyme loci with a sample of 164 individuals distributed in six natural populations located in the States of Pernambuco and Alagoas, Northeastern Brazil. The results showed a high level of genetic diversity within the species (e= 0.36) seeing that the most of the genetic variability of H. speciosa var. speciosa is within its natural populations with low difference among populations ( or = 0.081). The inbreeding values within ( = -0.555) and among populations ( =-0.428) were low showing lacking of endogamy and a surplus of heterozygotes. The estimated gene flow ( m ) was high, ranging from 2.20 to 13.18, indicating to be enough to prevent the effects of genetic drift and genetic differentiation among populations. The multivariate analyses indicated that there is a relationship between genetic and geographical distances, which was confirmed by a spatial pattern analysis using Mantel test (r = 0.3598; p = 0.0920) with 1000 random permutations. The high genetic diversity index in these populations indicates potential for in situ genetic conservation.

Development of plurimetallic electrocatalysts prepared by decomposition of polymeric precursors for EtOH/O2 fuel cell

This work aimed to develop plurimetallic electrocatalysts composed of Pt, Ru, Ni, and Sn supported on C by decomposition of polymeric precursors (DPP), at a constant metal:carbon ratio of 40:60 wt.%, for application in direct ethanol fuel cell (DEFC). The obtained nanoparticles were physico-chemically characterized by X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDX). XRD results revealed a face-centered cubic crystalline Pt with evidence that Ni, Ru, and Sn atoms were incorporated into the Pt structure. Electrochemical characterization of the nanoparticles was accomplished by cyclic voltammetry (CV) and chronoamperometry (CA) in slightly acidic medium (0.05 mol L-1 H2SO4), in the absence and presence of ethanol. Addition of Sn to PtRuNi/C catalysts significantly shifted the ethanol and CO onset potentials toward lower values, thus increasing the catalytic activity, especially for the quaternary composition Pt64Sn15Ru13Ni8/C. Electrolysis of ethanol solutions at 0.4 V vs. RHE allowed determination of acetaldehyde and acetic acid as the main reaction products. The presence of Ru in alloys promoted formation of acetic acid as the main product of ethanol oxidation. The Pt64Sn15Ru13Ni8/C catalyst displayed the best performance for DEFC.

Overview of semi-sinusoidal stellar variability with the CoRoT satellite

Context. To date, the CoRoT space mission has produced more than 124 471 light curves. Classifying these curves in terms of unambiguous variab ility behavior is mandatory for obtaining an unbi ased statistical view on th eir controlling root-causes. Aims. The present study provides an overview of semi-sinusoidal light curves observed by the CoRoT exo-field CCDs. Methods. We selected a sample of 4206 light curves presenting well-defined semi-si nusoidal signatures. Th e variability periods were computed based on Lomb-Scargle periodograms, harmonic fits, and visual inspection. Results. Color–period diagrams for the present sample show the trend of an increase of the variability periods as long as the stars evolve. This evolutionary behavior is also noticed when comparing the period distribution in the Galactic center and anti-center directions. These aspect s indicate a compatibility with stellar rotation, although more inform ation is needed to confirm their root- causes. Considering this possi bility, we identified a subset of th ree Sun-like candidates by their photometric peri od. Finally, the variability period versus color diagr am behavior was found to be highly depe ndent on the reddening correction.