Correlações entre zona de estiramento e tenacidade à fratura para aço 15-5PH

This work includes a study on the stretch zone and the influence of the toughness conditions at fracture in size and appearance. It was done a literature review about material properties, fracture mechanics concepts, definitions and formation of stretch zone, importance of tenacity for structural calculation, methods and standards to measure the toughness of metallic material fracture and presents the method used in microscopy. After the literature review were carried out identification and measurements of stretch zones of proof bodies were made through confocal optical microscopy and then analyzed the results in order to find relationships between the values obtained with the theory

Influência do comprimento do pino de fibra de vidro na resistência à fratura de raízes fragilizadas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito de diversos protocolos de dessensibilização dentinária na obliteração de túbulos dentinários, resistência de união do sistema adesivo e formação de camada hibrida na dentina cervical

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efeitos de lasers de alta potência na superfície de cerâmicas vítreas de dissilicato de lítio e sua resistência de união à dentina humana

Pós-graduação em Odontologia Restauradora - ICT

Metodologia construtiva de paredes diafragma

In the study line about contention, using Diaphragm Wall, revising the characteristics, vantages and constructive methods, following the application due to Terzaghi's theory. This work will be revising the advantages of the excavation equipments like the Clamshell and the Hydraulic Rolling Excavator, excavation techniques, and types of steel reinforcements, concreting, draining methodologies and comparison with other techniques. Also, will be revised a Study of Case, which by the application of two executive methodologies, will be possible to make a comparative analyses in a real construction situation.

Influência da incorporação de nanofibras de poliamida 6 com e sem nanotubos de carbono como reforço de prótese parcial fixa adesiva

The aim of this study was to evaluate the behavior of reinforced composites with polyamide 6 fibers aligned (6000 rpm) and alignment (120 rpm) with or without CNT using the flexural strength test. After preparation of nanofibers aligned nylon 6 (6000 rpm) and alignment (120 rpm) with and without incorporation of nanotube carbon by the method of electrospinning, were performed one control group (n = 10) and 4 experimental groups (n = 40) G1: Control (just resin Charisma - Heraeus Kulzer) ;G2 Resin + N6 aligned (6000 rpm) + CNT; G3:Resin + N6 alignment (120 rpm) + CNT; G4: Resin + aligned ( 6000 rpm) N6. G5: Resin + N6 alignment (120 rpm). The fibers were cut to the dimensions of 0,3 x 15 mm and were applied an adhesive at the surface (Single Bond 2) for 5 min and cured. In the matrix, was added resin in the proximal box (Charisma A2, Heraeus Kulzer) and cured for 40 s. (power 1100 mW / cm²). A first layer of resin and on the resin was deposited. The resin layers specimens were light irradiated with three overlapping exposures delivered. For each resin layer were light irradiated for 40 sec. The samples were tested with a cross-speed of 1 mm / min, and a 50 Kgf at Universal testing machine (EMIC mod.DL2000). The Dunnet test showed that only the nanotube group was significantly different from the control group. The ANOVA two-way indicates that the nanotube factor was statistically significant (p < 0.05) and there is no interaction between factors and orientation nanotube. The presence of nanotube showed lower fracture resistance values for aligned and unaligned groups. The results of this study showed that the orientation of the fibers does not influence the strength of composite resins and the incorporation of nylon nanofibers with carbon nanotubes decreased the fracture resistance values. The presence of the fibers has not been able to improve the strength of the material in any of the...

Oscilador harmônico unidimensional via transformada unilateral de Fourier e mapeamento do potencial de morse unidimensional nos potenciais pseudo-harmônico e de kratzer tridimensionais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação comparativa do grau de deformação plástica aplicado a componentes obtidos por conformação

The manufacturing process of components of Pressure Vessels has a great importance in the efficiency during the operation and life cycle of the equipment. Taking this into account, the objective of this dissertation was to analyze the methods to determine the strain rate in formed components by measuring the components themselves, and posterior results comparison with the values found in manufacturing standards of Pressure vessels. In this study the whole manufacturing process of a component from a pressure vessel, known as Head or End, was accompanied. Using the methodology obtained from literatures it was possible to execute the relative and logarithmic deformation measurements of these components and compare with the obtained results by means of equations presented in the Standards as AD-Merkblatt and ASME (for pressure vessels). The found results were also compared with the logarithmic methodology, taking into account the deformation of the empirical mesh and the thickness of the components studied. It is possible to conclude from this study that despite the existence of empirical methods of measurement of strain rate in components plastically formed, it is recommended the adoption in all situation of the component manufacturing standard. It can be noticed and explained during the development of this study and through the results found

Implementação de CADD nos cursos de graduação em engenharia mecânica

This study aims to demonstrate the importance of computer-aided design and drafting (CADD) software for mechanical engineers. In addition, evaluate the software: Inventor 2015, Creo 3.0 and Solid Edge ST8, developed by consolidate companies in the market. In order to accomplish those goals, software application and its advantages will be demonstrated for the industry and for the academia. The evaluation process consists in modeling two mechanical assemblies, in order to compare functional aspects among the software. At the end, it is concluded that the learning of CADD software is of great importance also is the basis for using Computer-aided Engineering (CAE) and Computer-Aided Manufacturing (CAM) tools. Furthermore, it is suggested that Inventor and Solid Edge are more likely to be used in the academia

Artroplastia total híbrida nacional em cães Portadores de displasia coxofemoral

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)