Estudo da cadeia petrolífera no Brasil: uma contextualização das tendências da indústria nacional e das relevâncias do PRH48

In the past few years, the Brazilian oil and gas sector had a considered growth, gaining enough relevance at international level, and being extremely important for the Brazilian socioeconomic development. However, the sector is still limited due to technical deficiencies. This work aims to conduct a current study, comprehending the entire oil chain, since it is possible to mention the Brazilian market updates on this context. To support this study, the historical development of the Brazilian petroleum industry was presented and the main stages of the production process were exposed with an emphasis on exploration and production phases. The new technologies developed for deepwater extractions, such as the pre-salt regions, were also discussed and, in the end, the relation of this growing market with the opportunities of the Human Resources Program of n. 48 was highlighted. This program identifies the market's actual needs and it's scarce's areas with the purpose of building capacity and qualified workforces, since it is also aimed, in a national level, a self-sufficient human resources for the sector

O ensino de matemática em duas escolas profissionalizantes: Brasil e Portugal, no período de 1942 a 1978

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização de trocadores de calor de placas em espiral em processos da indústria siderúrgica

Stricter environmental policies are shown necessary to ensure an effective pollutant emission control. It is expected for the present year of 2015, that Brazil will assume, at the 21th United Nation's Climate Change Conference (COP21), implementation of commitment to a low carbon economy. This positioning affects the industrial environment, so that is deemed necessary to search for new technologies, less aggressive to the environment, so the adequacies to the new emission policies do not cause a negative effect on production. Almost all of the processes performed in the steel industry demand burning fuel and, therefore, flue gases are sent to the atmosphere. In this present work is discussed the utilization of heat exchangers so, by recovering part of the available heat from the flue gases of certain industrial process, the combustion air is preheated. The combustion air preheat results in less energy requirement, i.e., less need of fuel consumption and, in addition, minor amount of pollutants to be emitted. Due to better fitting to the process, it is studied the utilization of spiral plate heat exchangers. The heat exchanger dimensioning is made by an iterative method implemented in the software Microsoft Excel. Subsequently are analyzed the gains in terms of process's thermal efficiency improvement and the percentage of fuel saving. The latter implies in reduction of the same percentage of greenhouse gases emission

Torneamento da liga de alumínio da classe 6005 utilizando ferramenta cerâmica

Machining processes are one of the most important manufacturing processes in the modern world. In these processes, there are many elements which will influence in the final result of the machined part. Among them, the tools are the principal factor of the rising cost, because its global influence on the process. In aeronautical industries, this can be more evidenced due the need to machining several alloys, between them, aluminum alloys. These alloys have to demonstrate a specific surface finishing to be used in aircraft's fuselage. This kind of industry is one of the segments which is still rising in Brazil, and they are looking viable alternatives in the manufacturing processes of materials, due the need to produce more and more parts and equipment, with costs increasingly reduced. The purpose of this project is the development of a ceramic with differentiated properties. The ceramics were developed using a pre-sintering at 1200 °C, with posterior sintering at 1600°C, and subjected to dry turning process on aluminum alloy 6005. The characterizations showed that ceramics presented with toughness on the center of 1700 MPa and on the surface of 1950 MPa, density 98,5 ±0,14. g/cm³. Ceramics were grinded and faceted, according to ISO standard 1832, and subjected to turning tests in a ROMI lathe brand, model GL240M, using cutting speeds of 500, 800 and 1000 m/min with different feed rates. The machining results showed low occurrence of flank wear to all cutting speeds, and better surface finishing average values of Ra = 0,4935 μm and Rt = 8,112 μm. In general, it could be seen that the tool presents important potential to machining 6005 alloy, and that the use of correct parameters can decrease and/or eliminate subsequent processes, providing important reductions in costs related to the machining processes