Quitosana na indução de resistência ao tombamento de plântulas de espécies olerícolas e no controle de fitopatógenos in vitro

Induction of resistance is defined as the activation of a state of resistance against diseases which is induced systemically in plants by the use of biotic or abiotic agents without any modification of the plant genome, occurring non-specific way, by activating genes coding for various plant defense responses. Chitosan is a polymer derived from the deacetylation of chitin, which is found in large quantities in crustacean shell, and studied with the potential to control plant pathogens, both by its direct fungistatic action, as the ability to induce protection of plants, indicating the presence of molecules of elicitoras characteristics. Three experiments with objective of evaluating the potential of chitosan in the seedling resistance induction were developed, beet (Beta vulgaris) seeds, cucumber (Cucumis sativus) seeds and tomato (Solanum lycopersicum) seeds, and the control of Fusarium sp., Rhizoctonia solani K¨uhn e Pythium sp. in vitro conditions. The experimental design was completely randomized, with four replications. Beet seeds, tomato and cucumber were submerged in chitosan solution for 20 minutes, in concentrations of 0.25, 0.5, 1 and 2% in the control and distilled water. Seeds were sown in trays containing Plantmax Florestalr substrate sterilized and inoculated with Fusarium sp., Rhizoctonia solani K¨unh and Pythium sp., respectively for the three cultures. The experiment was conducted for 14 days in growth chamber with controlled temperature (25 C 2 C), light (12 hour photoperiod) and humidity (70% 10%). The evaluations were seed emergency, seedling damping-off, seedling length, fresh weight and activity of the enzymes phenylalanine amˆonia-liase (PAL), chitinase and b-1,3-glucanase. It was also rated the mycelial growth of Fusarium sp., Pythium sp. and R. solani on P.D.A. (Potato-Dextrose and Agar) culture medium containing chitosan at the same concentrations evaluated in seeds. For beet growing, seed treatment with chitosan presented higher emergence and the length of the seedlings, and reduced the percentage of tipping. Treatment with chitosan activated the systemic acquired resistance with expression of chitinase and b-1,3-glucanase enzymes. For the tomato crop in chitosan concentration of 0.25% favored the emergency of seedlings, reduced the incidence of tipping and activated the PAL enzymes, chitinase and b-1,3-glucanase. In cucumber on the concentration of up 0.5% favored seedlings emergence and reduces the incidence of tipping. Chitosan activated the PAL enzymes and b-1,3-glucanase. Chitosan also presented fungistatic action on the initial growth of Pythium sp. and R. solani in vitro conditions, however, such action did not prevail until the end of the experiment. To Fusarium sp. the concentration of chitosan resulted in the reduction of mycelial growth in vitro.

Influência da temperatura de calcinação do fosfogesso no desempenho de cimentos supersulfatados

The supersulfated cement (CSS) basically consist of up to 90% blast furnace slag, 10-20% of a source of calcium sulfate and a small amount of alkali activator, covered by European standard EN 15743/2010. Because of this SSC are considered "green cement" low environmental impact. The source of calcium sulfate used in the preparation of CSS can be obtained from natural sources, such as gypsum or from alternative sources (industrial products), such as phosphogypsum. The phosphogypsum is a by-product of the fertilizer industry, used in the production of phosphoric acid. In this process the phosphate rock is treated with sulfuric acid to give as the major product phosphoric acid (H3PO4), gypsum and a small amount of hydrofluoric acid. The chemical composition of gypsum is basically calcium sulfate dihydrate (CaSO4.2H2O), similar to gypsum, because it can be used in this type of cement. To become anhydrous, the calcination of gypsum is necessary. The availability of the source of calcium sulfate to react with the slag is dependent on its solubility that is directly related to its calcination temperature. The solubility of the anhydrous gypsum decreases with increasing calcination temperature. This study investigated the influence of temperature of calcination of phosphogypsum on the performance of CSS. Samples were prepared with 10 and 20% of phosphogypsum calcinated at 350 to 650 ° C using KOH as an alkaline activator at three different concentrations (0.2, 0.5 and 0.8%). The results showed that all mortars presented the minimum values required by EN 15743/2010 for 7 and 28 days of hydration. In general CSS containing 10% phosphogypsum showed slightly better compressive strength results using a lower calcination temperature (350 °C) and curing all ages. The CSS containing 20% of calcined gypsum at 650 °C exhibit satisfactory compressive strenght at 28 days of hydration, but at later ages (56 to 90 days) it strongly reduced. This indicates that the calcination temperature of phosphogypsum has a strong influence on the performance of the CSS.