Enraizamento de mini-estacas de jabuticabeiras, pitangueira, araçazeiro amarelo e sete capoteiro

The most native fruit trees are belonging to Myrtaceae family, which it have as main marketing potential their fruit. Despite the wide acceptance of the fruits of these native fruit cultura, the establishment of commercial orchards is still necessary, because if it prevails extraction in the forest. To start the cultivo in the orchard, the first point is on the mother plant choice, which should provide superior characteristics when compared to other genotypes. Then, it is necessary to choose the method to can produce satisfactory amount of seedlings and preferably without it to lose the mother plant characteristics. For this, it adopts the asexual thechniques, with option for grafting, cuttings and air layering. These techniques when tested with native fruits tree, it proved limiting in theses results, with this, it should to test other it to recommend its use, especially, those fruit native of higher potential as jabuticaba tree, pitanga tree, sete capote tree and araça amarelo tree. The aim of this study was to test the use of asexual propagation through mini-cuttings in these native fruit trees, according to the time of collection, the mini-cutting length and concentration of IBA, as well as, it to relate the results of rooting with tryptophan extracted at certain times. The work was carried out at Universidade Tecnológica Federal do Paraná – Câmpus Dois Vizinhos, Brazil. The samples were collected each two months. The mini-cutting were prepared with 6 or 8 cm, with a pair of leaves reduced to 25% of the original size. The mini-cuttings had their base immersed in liquid solution of indole-butyric acid (IBA) in the concentrations of 0, 3000 and 6000 mg L-1 and then were placed in tubes containing commercial substrate. The experimental design was completely randomized with factorial 2 x 3 x 6 (mini-cutting length x IBA concentration x time of collection), with four replications, it being each plot varied according to the amount of shoots obtained by period time. After 120 days, the rooting and callus formation (%), average number of roots per mini-cutting and the average length of the roots were evaluated. After 60 days of these evaluations, the survival of mini-cuttings rooted after transplant was evaluated. It was evaluated also the production of mini-cuttings of each size in each period time. At the end of the experiment it was evaluated the percentage of survival of mother plantlets. For analysis of tryptophan was used materials branches, leaves and twigs with leaves, taken from the materials used for the production of mini-cutting. It was recommended for hybrid jabuticaba tree the use mini-cutting with eight cm, treated with 6000 mg L-1 of IBA and collected in June. For jabuticaba tree of cabinho and araça amarelo tree the period for propagation by mini-cuttings should be in August, regardless of IBA concentration and length of the mini-cutting. In the jabuticaba tree sabara and sete capote tree is important to obtain more satisfactory results realized the collect in October or December, with the same independence of other levels tested in other factors. However, for sete capote tree should test other techniques to increase the efficiency of propagation. And with pitanga tree recommended to the collection in June, but with 6cm the application of 3000 mg L-1 of IBA and 8 cm with 6000 mg L-1 of IBA.

Caracterização elementar de ligas metálicas em implantes dentários

An ideal biomaterial for dental implants must have very high biocompatibility, which means that such materials should not provoke any serious adverse tissue response. Also, used metal alloys must have high fatigue resistance due the masticatory force and good corrosion resistance. These properties are rendered by using alpha and beta stabilizers, such as Al, V, Ni, Fe, Cr, Cu, Zn. Commercially pure titanium (TiCP) is used often for dental and orthopedic implants manufacturing. However, sometimes other alloys are employed and consequently it is essential to research the chemical elements present in those alloys that could bring prejudice for the health. Present work investigated TiCP metal alloys used for dental implant manufacturing and evaluated the presence of stabilizing elements within existing limits and standards for such materials. For alloy characterization and identification of stabilizing elements it was used EDXRF technique. This method allows to perform qualitative and quantitative analysis of the materials using the spectra of the characteristic X-rays emitted by the elements present in the metal samples. The experimental setup was based on two X- rays tubes (AMPTEK Mini X model with Ag and Au targets), a X-123SDD detector (AMPTEK) and a 0.5mm Cu collimator, developed due to the sample characteristics. The other experimental setup used as a complementary technique is composed of an X-ray tube with a Mo target, collimator 0.65mm and XFlash (SDD) detector - ARTAX 200 (BRUKER). Other method for elemental characterization by energy dispersive spectroscopy (EDS) applied in present work was based on Scanning Electron Microscopy (SEM) EVO® (Zeeis). This method also was used to evaluate the surface microstructure of the sample. The percentual of Ti obtained in the elementary characterization was among 93.35 ± 0.17% and 95.34 ± 0.19 %. These values are considered below the reference limit of 98.635% to 99.5% for TiCP, established by Association of metals centric materials engineers and scientists Society (ASM). The presence of elements Al and V in all samples also contributed to underpin the fact that are not TiCP implants. The values for Al vary between 6.3 ± 1.3% and 3.7 ± 2.0% and for V, between 0.26 ± 0.09% and 0.112 ± 0.048%. According to the American Society for Testing and Materials (ASTM), these elements should not be present in TiCP and in accordance with the National Institute of Standards and Technology (NIST), the presence of Al should be <0.01% and V should be of 0.009 ± 0.001%. Obtained results showed that implant materials are not exactly TiCP but, were manufactured using Ti-Al-V alloy, which contained Fe, Ni, Cu and Zn. The quantitative analysis and elementary characterization of experimental results shows that the best accuracy and precision were reached with X-Ray tube with Au target and collimator of 0.5 mm. Use of technique of EDS confirmed the results of EDXRF for Ti-Al-V alloy. Evaluating the surface microstructure by SEM of the implants, it was possible to infer that ten of the thirteen studied samples are contemporaneous, rough surface and three with machined surface.