Efeito de agentes de controle sobre a qualidade reprodutiva de rainhas de Apis mellifera L. (Hymenoptera: Apidae) africanizadas

The agriculture with the use of products with less environmental impact is expanding. In it, the producers offer their products without the use of synthetic chemical inputs, solving the phytosanitary problems with the use of biological or alternative control agents such as parasites, predators, entomopathogenic, alternative products, plant extracts and essential oils. These products can be considered safe to non-target organisms, but studies are needed to find these features on natural enemies and on the beneficial insects such as bees, common frequenter of cultures. In this sense, this study aims to evaluate the effects of control over reproductive quality queens of Apis mellifera L. (Hymenoptera: Apidae) Africanized. For this, it tested the action of control products on the production of A. mellifera queens, using the commercial entomopathogenic fungus Boveril® 1,0x108 (Beauveria bassiana) and aqueous extract of pomegranate (Punica granatum) at a concentration of 5% sterile distilled water with Tween (0.01%) and sterile distilled water (controls). The treatments were incorporated into a tissue type gauze, wrapped in an acrylic plate and packed inside minirrecrias type colonies for the production of queens on the day before the transfer of larvae. The next day were introduced battens with 30 domes with larvae to produce queens, so the workers have contacted the agent tested. From the emergence of all the queens, they were monitored to determine the measures of body weight (mg), length and width of wing and abdomen, length, width and height of the chest (mm) as well as the time of emergence of queens. The next step was evaluated the influence of the control agents in production creates, performing measurements of creating areas in cm2 for six straight weeks. It was found that the area creates Queens did not differ among the treatments. Histological analysis of hipofaringeanas of workers glands that came into contact with the control agents and the midgut of virgin queens were also held. Histological analysis differences were observed in the tissues when the treatments were compared with the respective controls.

Influência da temperatura de calcinação do fosfogesso no desempenho de cimentos supersulfatados

The supersulfated cement (CSS) basically consist of up to 90% blast furnace slag, 10-20% of a source of calcium sulfate and a small amount of alkali activator, covered by European standard EN 15743/2010. Because of this SSC are considered "green cement" low environmental impact. The source of calcium sulfate used in the preparation of CSS can be obtained from natural sources, such as gypsum or from alternative sources (industrial products), such as phosphogypsum. The phosphogypsum is a by-product of the fertilizer industry, used in the production of phosphoric acid. In this process the phosphate rock is treated with sulfuric acid to give as the major product phosphoric acid (H3PO4), gypsum and a small amount of hydrofluoric acid. The chemical composition of gypsum is basically calcium sulfate dihydrate (CaSO4.2H2O), similar to gypsum, because it can be used in this type of cement. To become anhydrous, the calcination of gypsum is necessary. The availability of the source of calcium sulfate to react with the slag is dependent on its solubility that is directly related to its calcination temperature. The solubility of the anhydrous gypsum decreases with increasing calcination temperature. This study investigated the influence of temperature of calcination of phosphogypsum on the performance of CSS. Samples were prepared with 10 and 20% of phosphogypsum calcinated at 350 to 650 ° C using KOH as an alkaline activator at three different concentrations (0.2, 0.5 and 0.8%). The results showed that all mortars presented the minimum values required by EN 15743/2010 for 7 and 28 days of hydration. In general CSS containing 10% phosphogypsum showed slightly better compressive strength results using a lower calcination temperature (350 °C) and curing all ages. The CSS containing 20% of calcined gypsum at 650 °C exhibit satisfactory compressive strenght at 28 days of hydration, but at later ages (56 to 90 days) it strongly reduced. This indicates that the calcination temperature of phosphogypsum has a strong influence on the performance of the CSS.