Avaliação inorgânica de material particulado atmosférico inalável na região norte do Paraná

This study aimed to determine the concentration and inorganic chemical composition of samples from airborne particulate matter inhaled in fine and coarse fractions. Aerosol samples were collected in 2013 and 2014, from sites located in the cities of Londrina and Maringa, in the state of Paraná, Brazil. The samples were collected daily (24h) in two campaigns: winter and summer. For the collection, was used a dichotomous sampler with quartz fiber filter with 47 mm in size and 2 µm porosity, 97% efficiency, retaining particles of up to 0.3 µm. Quantification of the airborne particulate matter mass was performed by gravimetry method. The results from Londrina to PM2.5 and MP2,5-10 represent, respectively, 29.2% and 70.8% of airborne particulate matter in the winter campaign (2013), 30.9% (PM2.5) and 69.1 % (MP2,5-10) in the summer campaign (2013), and 35.9% (PM2.5) and 64.1% (MP2,5-10) in the winter 2014 campaign. In the city of Maringa, the results presented the percentage of 42.0% (PM2.5) and 58.0% (MP2,5-10) for the winter season (2014), and 28.8% (PM2.5) and 71.2 % (MP2,5-10) for the summer season (2014). The PM2.5/PM10 ratio was on average 0.3, demonstrating that both cities are developing urban areas. Analysis of the major soluble inorganic species in water (NO3-, SO42- and Cl-) associated with MP2,5-10 were quantified by ion chromatography at the LACA Laboratory in the State University of Londrina, with the largest contribution found in all campaigns was to NO3-. The NO3-/SO42- ratios above 1.0 indicate the local traffic contribution. The analysis of metals associated with PM2.5 was carried out by mass spectrometry with inductively coupled plasma (ICP-MS) in the Federal University of Santa Catarina. The Zn, Pb, Cu and Mn concentrations found in all campaigns indicate the contribution of mobile sources to PM2.5. The concentration of BCe in PM2.5 was determined by reflectance, with higher BCe concentrations being found in winter campaigns. In general, Londrina presented the highest concentrations from the species analyzed when compared to Maringá. In addition, the analysis of the air mass trajectories indicated the transportation of pollutants coming mainly from fires in the southeastern region of the country.

Desempenho de soja associado à posição do fertilizante e tamanho de sementes

The seed size used for seeding has caused doubts among soybean producers. The study aimed to determine whether there may be differences between seed size with respect to depth of fertilizer deposition. The field experiment was conducted at the Experimental Area UTFPR Campus Pato Branco, using a precision seeder for direct seeding. The design was a randomized blocks, with five repetitions. The treatments were composed by the combination of two seed sizes (large seed with 6,5 mm and 5,5 mm with small seed) and two fertilizer deposition depths in relation to the seed (fertilizer near the seed with about 3 cm away and fertilizer distant from the seeds with about 10 cm). Data were subjected to analysis of variance. When the test value F was significant at 5% probability was applied to the Duncan test for comparison of means. The shallower depth of fertilizer deposition provided larger number of pods per plant and increased number of grains per plant. Already the largest depth of fertilizer deposition provided greater plant height at 30 days after sowing and R2 stage, greater ground area mobilized, higher plant population in all periods, greater depth of deposition of seeds and a higher rate of emergency speed.

Aplicação da metodologia numérica “fast bounds crack” para uma estimativa eficiente da evolução do tamanho de trinca

A significant part of the life of a mechanical component occurs, the crack propagation stage in fatigue. Currently, it is had several mathematical models to describe the crack growth behavior. These models are classified into two categories in terms of stress range amplitude: constant and variable. In general, these propagation models are formulated as an initial value problem, and from this, the evolution curve of the crack is obtained by applying a numerical method. This dissertation presented the application of the methodology "Fast Bounds Crack" for the establishment of upper and lower bounds functions for model evolution of crack size. The performance of this methodology was evaluated by the relative deviation and computational times, in relation to approximate numerical solutions obtained by the Runge-Kutta method of 4th explicit order (RK4). Has been reached a maximum relative deviation of 5.92% and the computational time was, for examples solved, 130,000 times more higher than achieved by the method RK4. Was performed yet an Engineering application in order to obtain an approximate numerical solution, from the arithmetic mean of the upper and lower bounds obtained in the methodology applied in this work, when you don’t know the law of evolution. The maximum relative error found in this application was 2.08% which proves the efficiency of the methodology "Fast Bounds Crack".

Desenvolvimento e caracterização de micropartículas de amido reticuladas com agente fosfatado e avaliação da adsorção do azul de metileno

Starch has properties that make it one of the most studied biopolymers today. It is biodegradable, biocompatible, stable and non-toxic. This work has synthesis of starch and tapioca microparticles, through chemical modification by crosslinking with sodium tripolyphosphate agent in concentrations 7.5 and 15% (m / m). The amylose content was measured for starch and commercial cassava starch at 21.8% and 28.6%, respectively. According to the solubility index, processing in basic medium does not change the solubility of the material, but the addition of crosslinking agent increases this index, which changed from 12.8% for the control unprocessed, to 22.4% for the A5R15 sample. Soluble starch-based materials had a significant increase in the crosslinking density by increasing the concentration of crosslinker, from 1.4 in A5R7,5 sample, to 1.9 in A5R15. The cassava starch-based materials exhibited an opposite behavior: to increase the concentration of crosslinker crosslinking density decreased significantly in F5R7.5 from 2.9, to 1.9 in F5R15 sample. The point of zero charge (PZC) shows that below pH 4 the surface is positively charged. The surface area data is between 3,04 and 1,15 m2.g-1. The pore volume between 2.94 and 1.33 cm3.g-1 and pore size around 1.5 nm. The SEM indicates uneven distribution of microparticles, which are smooth, with no ridges. The maximum adsorption capacity of the materials were tested at pH 7.7 and for A5R15 and CA sample, at pH 2, 5, 6 and 9. It is noted that the processing in basic medium reduces the adsorption capacity of CA and CF in respect fo A and F. The adsorption in A5R15 sample has great dependency on the pH, reaching a value of 587 μg.g-1 in pH 7.7. The samples A5R15 and F5R7,5 adsorbed similar amounts, according to the statistical analysis, and significantly higher than their respective controls and showed lower desorption, indicating that the modification process was effective to control the release of methylene blue. The infrared spectra not show the characteristic bands of the phosphate bonds to the material formed, however, developments in hydroxyl characteristic band suggest modification in the way this group was linked after the reaction. After adsorption, the infrared spectra show different format in the band of hydroxyl. PCA analysis shows that the greatest changes observed in the IR spectra are observed in the region of 3500 cm-1. Thermal analysis showed three thermal events related to dehydration and material degradation. It is observed that the processing increases the temperature to the first mass loss, fixed at 12%, but not observed increased stability due to the presence of crosslinker or process.

Protocolo de roteamento para redes oportunistas utilizando otimização por enxame de partículas

In this research work, a new routing protocol for Opportunistic Networks is presented. The proposed protocol is called PSONET (PSO for Opportunistic Networks) since the proposal uses a hybrid system composed of a Particle Swarm Optimization algorithm (PSO). The main motivation for using the PSO is to take advantage of its search based on individuals and their learning adaptation. The PSONET uses the Particle Swarm Optimization technique to drive the network traffic through of a good subset of forwarders messages. The PSONET analyzes network communication conditions, detecting whether each node has sparse or dense connections and thus make better decisions about routing messages. The PSONET protocol is compared with the Epidemic and PROPHET protocols in three different scenarios of mobility: a mobility model based in activities, which simulates the everyday life of people in their work activities, leisure and rest; a mobility model based on a community of people, which simulates a group of people in their communities, which eventually will contact other people who may or may not be part of your community, to exchange information; and a random mobility pattern, which simulates a scenario divided into communities where people choose a destination at random, and based on the restriction map, move to this destination using the shortest path. The simulation results, obtained through The ONE simulator, show that in scenarios where the mobility model based on a community of people and also where the mobility model is random, the PSONET protocol achieves a higher messages delivery rate and a lower replication messages compared with the Epidemic and PROPHET protocols.