Desempenho de sulcadores no desenvolvimento e produtividade da soja em solo submetido a diferentes níveis de compactação

On the national scene, soybean crop occupies a prominent position in cultivated area and volume production, being cultivated largely in the no tillage system. This system, due to the intense traffic of machines and implements on its surface has caused soil compaction problems, which has caused the yield loss of crops. In order to minimize this effect the seeder-drill uses the systems to opening the furrow by shank or the double disc type. The use of the shank has become commonplace for allowing the disruption of the compacted surface layer, however requires greater energy demand and may cause excessive tillage in areas where there is not observed high levels of compaction. Thus, this study aimed to evaluate the effects of furrowers mechanisms and levels of soil compacting on traction requirement by a seeder-drill and on the growing and productivity of soybean in an Oxisol texture clay, in a two growing seasons. The experimental design consisted of randomized blocks with split plots with the main plots composed of four levels of soil compaction (N0 – no tillage without additional compaction, N1, N2 and N3 – no tillage subjected to compaction through two, four and six passes with tractor, respectively) corresponding to densities of soil 1.16, 1.20, 1.22 and 1.26 g cm-3, and subplots by two furrowers mechanisms (shank and double disc) with four replicates. To evaluate the average, maximum and specific traction force requested by the seeder-drill, was used a load cell, with capacity of 50 kN and sensitivity of 2 mV V-1, coupled between the tractor and seeder-drill, whose data are stored in a datalogger system model CR800 of Campbell Scientific. In addition, were evaluated the bulk density, soil mechanical resistance to penetration, sowing depth, depth and groove width, soil area mobilized, emergence speed index, emergence operation, final plant stand, stem diameter, plant height, average number of seeds per pod, weight of 1,000 seeds, number of pods per plant and crop productivity. Data were subjected to analysis of variance, the mean of furrowers were compared by Tukey test (p≤0.05), while for the factor soil compaction, polynomial regression analysis was adopted, selected models by the criterion of greater R2 and significance (p≤0.05) of equation parameters. Regardless of the crop season, penetration resistance increase as soil compaction levels up to around 0.20 m deep, and bulk density influenced the sowing quality parameters, however, did not affect the crop yield. In the first season, there was a higher productivity with the use of the shank type. In the second crop season, the shank demanded greater energetic requirement with the increase of bulk density and opposite situation with the double disc. The locking of sowing lines allow better performance of the shank to break the compacted layer.

Desempenho de sementes de soja revestidas com biopolímeros

The use of biopolymers that help to fix pesticides efficiently and degrade easily without harming the environment, and still improve the physiological performance of field soybean seed may bring contributions to the soybean yield. This study aimed to evaluate the effect of cassava starch polymers (AM), sodium alginate (ALG) and polyvinyl alcohol (PVOH), in the concentrations 2, 4 and 6 g / 100 ml of solution, in the physiological attributes of seeds soy, seed speed soaking and performance of soybean seeds after three months of storage. The soybean variety used was the NK 7059 RR. The experimental design used for the three studies was a factorial with 48 experimental units: 3 polymers (AM, ALG and PVOH), 4 different concentrations (0%, 2%, 4% and 6%), with four replications, in a completely randomized design. It was observed the level of significance of the factors and their interactions, applying the test F. The polymers were evaluated by the Tukey test at 5% probability, and the concentrations were evaluated by polynomial regression. The witness obtained better results for most variables studied. Among the polymers, the best coating was observed PVOH because it was the less viscous polymer and visually not served as a substrate for microorganisms. However, also, satisfactory results were obtained for the AM and ALG polymers at a concentration of 2%. There was not interference of the polymers studied with regard to reduction of imbibition rate of soybean seeds. The hydrophilicity of polymers, mainly the AM and ALG accelerated soaking seeds harming germination at concentrations 4% and 6%. In general, the higher the concentration of polymers tended to worse results.

Medidas de concentração de radônio proveniente de argamassas de cimento portland, gesso e fosfogesso

Portland cement being very common construction material has in its composition the natural gypsum. To decrease the costs of manufacturing, the cement industry is substituting the gypsum in its composition by small quantities of phosphogypsum, which is the residue generated by the production of fertilizers and consists essentially of calcium dihydrate and some impurities, such as fluoride, metals in general, and radionuclides. Currently, tons of phosphogypsum are stored in the open air near the fertilizer industries, causing contamination of the environment. The 226 Ra present in these materials, when undergoes radioactive decay, produces the 222Rn gas. This radioactive gas, when inhaled together with its decay products deposited in the lungs, produces the exposure to radiation and can be a potential cause of lung cancer. Thus, the objective of this study was to measure the concentration levels of 222Rn from cylindrical samples of Portland cement, gypsum and phosphogypsum mortar from the state of Paraná, as well as characterizer the material and estimate the radon concentration in an environment of hypothetical dwelling with walls covered by such materials. Experimental setup of 222Rn activity measurements was based on AlphaGUARD detector (Saphymo GmbH). The qualitative and quantitative analysis was performed by gamma spectrometry and EDXRF with Au and Ag targets tubes (AMPTEK), and Mo target (ARTAX) and mechanical testing with x- ray equipment (Gilardoni) and the mechanical press (EMIC). Obtained average values of radon activity from studied materials in the air of containers were of 854 ± 23 Bq/m3, 60,0 ± 7,2 Bq/m3 e 52,9 ± 5,4 Bq/m3 for Portland cement, gypsum and phosphogypsum mortar, respectively. These results extrapolated into the volume of hypothetical dwelling of 36 m3 with the walls covered by such materials were of 3366 ± 91 Bq/m3, 237 ± 28 Bq/m3 e 208 ± 21 Bq/m3for Portland cement, gypsum and phosphogypsum mortar, respectively. Considering the limit of 300 Bq/m3 established by the ICRP, it could be concluded that the use of Portland cement plaster in dwellings is not secure and requires some specific mitigation procedure. Using the results of gamma spectrometry there were calculated the values of radium equivalent activity concentrations (Raeq) for Portland cement, gypsum and phosphogypsum mortar, which were obtained equal to 78,2 ± 0,9 Bq/kg; 58,2 ± 0,9 Bq/kg e 68,2 ± 0,9 Bq/kg, respectively. All values of radium equivalent activity concentrations for studied samples are below the maximum level of 370 Bq/kg. The qualitative and quantitative analysis of EDXRF spectra obtained with studied mortar samples allowed to evaluate quantitate and the elements that constitute the material such as Ca, S, Fe, and others.