A altura de dossel e a adubação nitrogenada da pastagem podem afetar a nutrição nitrogenada do milho, num sistema de integração lavoura pecuária?

We conducted a field experiment near Abelardo Luz, Santa Catarina, from October 2012 to April 2014, to evaluate the effect interaction of nitrogen fertilization and height of canopy over the N nutrition of corn subsequently grown to pasture. The data belonging to this thesis are related to the first two production cycles obtained in sorghum pasture (2012/2013), oat (2013) and corn crop (2013/2014). In the evaluation of forage sorghum and oat it was used the same experimental design, consisting of randomized complete block in a factorial arrangement (2 x 2) with three replications. The first factor was considered canopy height (Low and High) and the second factor was the fertilization of cover crop pasture (0 and 200 kg N.ha-1). In phase I and II, the combination of factors evaluators were prepared in the same experimental unit. For corn crop the design was a randomized complete block in a factorial design (2X2X4X6) with three replications. Factors considered in corn were: canopy height of pasture (Low and High), nitrogen application times (NG - nitrogen in the grains and NP - nitrogen in pasture), nitrogen fertilization in corn (0, 100, 200 and 300 kg N.ha-1) and time (46, 53, 60, 67, 76 and 103 days after sowing the maize). In phases I and II, in general the use of N in the pasture increased the productive potential of the pasture and animal management and canopy height has changed the dynamics of structural components and botanical pasture. In cold conditions for long periods and not acclimatized plants the adoption of high nitrogen fertilization and height high grazing pasture leave vulnerable to damage caused by the freezing of plants. The anticipation of nitrogen fertilization on pasture positively affects the corn crop by increasing the accumulated dry matter and N content in the plant. Nitrogen nutritional content of corn with the anticipation of fertilization in pasture is suitable for obtaining high crop production in integrated crop-livestock system. When used nitrogen only coverage in corn sufficiency level in the nitrogen nutrition is achieved with the use of 100 kg N.ha-1. With the use of 200 kg N ha -1 NG and NP no difference in nitrogen content and nitrogen nutrition index.

Caracterização elementar de ligas metálicas em implantes dentários

An ideal biomaterial for dental implants must have very high biocompatibility, which means that such materials should not provoke any serious adverse tissue response. Also, used metal alloys must have high fatigue resistance due the masticatory force and good corrosion resistance. These properties are rendered by using alpha and beta stabilizers, such as Al, V, Ni, Fe, Cr, Cu, Zn. Commercially pure titanium (TiCP) is used often for dental and orthopedic implants manufacturing. However, sometimes other alloys are employed and consequently it is essential to research the chemical elements present in those alloys that could bring prejudice for the health. Present work investigated TiCP metal alloys used for dental implant manufacturing and evaluated the presence of stabilizing elements within existing limits and standards for such materials. For alloy characterization and identification of stabilizing elements it was used EDXRF technique. This method allows to perform qualitative and quantitative analysis of the materials using the spectra of the characteristic X-rays emitted by the elements present in the metal samples. The experimental setup was based on two X- rays tubes (AMPTEK Mini X model with Ag and Au targets), a X-123SDD detector (AMPTEK) and a 0.5mm Cu collimator, developed due to the sample characteristics. The other experimental setup used as a complementary technique is composed of an X-ray tube with a Mo target, collimator 0.65mm and XFlash (SDD) detector - ARTAX 200 (BRUKER). Other method for elemental characterization by energy dispersive spectroscopy (EDS) applied in present work was based on Scanning Electron Microscopy (SEM) EVO® (Zeeis). This method also was used to evaluate the surface microstructure of the sample. The percentual of Ti obtained in the elementary characterization was among 93.35 ± 0.17% and 95.34 ± 0.19 %. These values are considered below the reference limit of 98.635% to 99.5% for TiCP, established by Association of metals centric materials engineers and scientists Society (ASM). The presence of elements Al and V in all samples also contributed to underpin the fact that are not TiCP implants. The values for Al vary between 6.3 ± 1.3% and 3.7 ± 2.0% and for V, between 0.26 ± 0.09% and 0.112 ± 0.048%. According to the American Society for Testing and Materials (ASTM), these elements should not be present in TiCP and in accordance with the National Institute of Standards and Technology (NIST), the presence of Al should be <0.01% and V should be of 0.009 ± 0.001%. Obtained results showed that implant materials are not exactly TiCP but, were manufactured using Ti-Al-V alloy, which contained Fe, Ni, Cu and Zn. The quantitative analysis and elementary characterization of experimental results shows that the best accuracy and precision were reached with X-Ray tube with Au target and collimator of 0.5 mm. Use of technique of EDS confirmed the results of EDXRF for Ti-Al-V alloy. Evaluating the surface microstructure by SEM of the implants, it was possible to infer that ten of the thirteen studied samples are contemporaneous, rough surface and three with machined surface.