Desempenho de sulcadores no desenvolvimento e produtividade da soja em solo submetido a diferentes níveis de compactação

On the national scene, soybean crop occupies a prominent position in cultivated area and volume production, being cultivated largely in the no tillage system. This system, due to the intense traffic of machines and implements on its surface has caused soil compaction problems, which has caused the yield loss of crops. In order to minimize this effect the seeder-drill uses the systems to opening the furrow by shank or the double disc type. The use of the shank has become commonplace for allowing the disruption of the compacted surface layer, however requires greater energy demand and may cause excessive tillage in areas where there is not observed high levels of compaction. Thus, this study aimed to evaluate the effects of furrowers mechanisms and levels of soil compacting on traction requirement by a seeder-drill and on the growing and productivity of soybean in an Oxisol texture clay, in a two growing seasons. The experimental design consisted of randomized blocks with split plots with the main plots composed of four levels of soil compaction (N0 – no tillage without additional compaction, N1, N2 and N3 – no tillage subjected to compaction through two, four and six passes with tractor, respectively) corresponding to densities of soil 1.16, 1.20, 1.22 and 1.26 g cm-3, and subplots by two furrowers mechanisms (shank and double disc) with four replicates. To evaluate the average, maximum and specific traction force requested by the seeder-drill, was used a load cell, with capacity of 50 kN and sensitivity of 2 mV V-1, coupled between the tractor and seeder-drill, whose data are stored in a datalogger system model CR800 of Campbell Scientific. In addition, were evaluated the bulk density, soil mechanical resistance to penetration, sowing depth, depth and groove width, soil area mobilized, emergence speed index, emergence operation, final plant stand, stem diameter, plant height, average number of seeds per pod, weight of 1,000 seeds, number of pods per plant and crop productivity. Data were subjected to analysis of variance, the mean of furrowers were compared by Tukey test (p≤0.05), while for the factor soil compaction, polynomial regression analysis was adopted, selected models by the criterion of greater R2 and significance (p≤0.05) of equation parameters. Regardless of the crop season, penetration resistance increase as soil compaction levels up to around 0.20 m deep, and bulk density influenced the sowing quality parameters, however, did not affect the crop yield. In the first season, there was a higher productivity with the use of the shank type. In the second crop season, the shank demanded greater energetic requirement with the increase of bulk density and opposite situation with the double disc. The locking of sowing lines allow better performance of the shank to break the compacted layer.

Caracterização do ciclo da marcha em amputado transtibial com prótese inteligente

This work presents an application of optical fiber sensors based on Bragg gratings integrated to a transtibial prosthesis tube manufactured with a polymeric composite systrem of epoxy resin reinforced with glass fiber. The main objective of this study is to characterize the sensors applied to the gait cycle and changes in the gravity center of a transtibial amputee, trough the analysis of deformation and strengh of the transtibial prosthesis tube. For this investigation it is produced a tube of the composite material described above using the molding method of resin transfer (RTM) with four optical sensors. The prosthesis in which the original tube is replaced is classified as endoskeletal, has vacuum fitting, aluminium conector tube and carbon fiber foot cushioning. The volunteer for the tests was a man of 41 years old, 1.65 meters tall, 72 kilograms and left-handed. His amputation occurred due to trauma (surgical section is in the medial level, and was made below the left lower limb knee). He has been a transtibial prosthesis user for two years and eight months. The characterization of the optical sensors and analysis of mechanical deformation and tube resistance occurred through the gait cycle and the variation of the center of gravity of the body by the following tests: stand up, support leg without the prosthesis, support in the leg with the prosthesis, walk forward and walk backward. Besides the characterization of optical sensors during the gait cycle and the variation of the gravity center in a transtibial amputated, the results also showed a high degree of integration of the sensors in the composite and a high mechanical strength of the material.