Physical characteristics of small ions and their interaction with ultrafine particles in the urban environment

In recent years, the effect of ions and ultrafine particles on ambient air quality and human health has been well documented, however, knowledge about their sources, concentrations and interactions within different types of urban environments remains limited. This thesis presents the results of numerous field studies aimed at quantifying variations in ion concentration with distance from the source, as well as identifying the dynamics of the particle ionisation processes which lead to the formation of charged particles in the air. In order to select the most appropriate measurement instruments and locations for the studies, a literature review was also conducted on studies that reported ion and ultrafine particle emissions from different sources in a typical urban environment. The initial study involved laboratory experiments on the attachment of ions to aerosols, so as to gain a better understanding of the interaction between ions and particles. This study determined the efficiency of corona ions at charging and removing particles from the air, as a function of different particle number and ion concentrations. The results showed that particle number loss was directly proportional to particle charge concentration, and that higher small ion concentrations led to higher particle deposition rates in all size ranges investigated. Nanoparticles were also observed to decrease with increasing particle charge concentration, due to their higher Brownian mobility and subsequent attachment to charged particles. Given that corona discharge from high voltage powerlines is considered one of the major ion sources in urban areas, a detailed study was then conducted under three parallel overhead powerlines, with a steady wind blowing in a perpendicular direction to the lines. The results showed that large sections of the lines did not produce any corona at all, while strong positive emissions were observed from discrete components such as a particular set of spacers on one of the lines. Measurements were also conducted at eight upwind and downwind points perpendicular to the powerlines, spanning a total distance of about 160m. The maximum positive small and large ion concentrations, and DC electric field were observed at a point 20 m downwind from the lines, with median values of 4.4×103 cm-3, 1.3×103 cm-3 and 530 V m-1, respectively. It was estimated that, at this point, less than 7% of the total number of particles was charged. The electrical parameters decreased steadily with increasing downwind distance from the lines but remained significantly higher than background levels at the limit of the measurements. Moreover, vehicles are one of the most prevalent ion and particle emitting sources in urban environments, and therefore, experiments were also conducted behind a motor vehicle exhaust pipe and near busy motorways, with the aim of quantifying small ion and particle charge concentration, as well as their distribution as a function of distance from the source. The study found that approximately equal numbers of positive and negative ions were observed in the vehicle exhaust plume, as well as near motorways, of which heavy duty vehicles were believed to be the main contributor. In addition, cluster ion concentration was observed to decrease rapidly within the first 10-15 m from the road and ion-ion recombination and ion-aerosol attachment were the most likely cause of ion depletion, rather than dilution and turbulence related processes. In addition to the above-mentioned dominant ion sources, other sources also exist within urban environments where intensive human activities take place. In this part of the study, airborne concentrations of small ions, particles and net particle charge were measured at 32 different outdoor sites in and around Brisbane, Australia, which were classified into seven different groups as follows: park, woodland, city centre, residential, freeway, powerlines and power substation. Whilst the study confirmed that powerlines, power substations and freeways were the main ion sources in an urban environment, it also suggested that not all powerlines emitted ions, only those with discrete corona discharge points. In addition to the main ion sources, higher ion concentrations were also observed environments affected by vehicle traffic and human activities, such as the city centre and residential areas. A considerable number of ions were also observed in a woodland area and it is still unclear if they were emitted directly from the trees, or if they originated from some other local source. Overall, it was found that different types of environments had different types of ion sources, which could be classified as unipolar or bipolar particle sources, as well as ion sources that co-exist with particle sources. In general, fewer small ions were observed at sites with co-existing sources, however particle charge was often higher due to the effect of ion-particle attachment. In summary, this study quantified ion concentrations in typical urban environments, identified major charge sources in urban areas, and determined the spatial dispersion of ions as a function of distance from the source, as well as their controlling factors. The study also presented ion-aerosol attachment efficiencies under high ion concentration conditions, both in the laboratory and in real outdoor environments. The outcomes of these studies addressed the aims of this work and advanced understanding of the charge status of aerosols in the urban environment.

Supply chain benefits expectation management framework

Organizations invest heavily in Supply Chain Management Systems expecting the benefits promised by the software vendors and the implementation partners. However, both academic and industry reports suggest that there is growing dissatisfaction among client organizations due to an increasing gap in benefits purported by the software vendors and benefits realised by the client. In order to better manage expectations of the client organization, this study proposes a Benefit Expectation Management Framework for Supply Chain Management Systems, based on Expectation-Confirmation Theory. This study derives 60 expected benefits of Supply Chain Management Systems through 41 vendor-reported customer stories and academic papers. Through comparing those benefits with the received benefits by a case organization that has implemented SAP Supply Chain Management Systems for seven years, two salient factors – long timetable and multiple stakeholders – have been identified as the controlling factors affecting the confirmation level of Supply Chain Management System expectations and further impacting the satisfaction of a client organization. The case study also highlights the likely causes for realized benefits and enduring issues in relation to the Supply Chain Management Systems.

A new database compilation of whole-rock chemical and geochronological data of igneous rocks in Queensland : a new resource for HDR geothermal resource exploration

The Geothermal industry in Australia and Queensland is in its infancy and for hot dry rock (HDR) geothermal energy, it is very much in the target identification and resource definition stages. As a key effort to assist the geothermal industry and exploration for HDR in Queensland, we are developing a comprehensive and new integrated geochemical and geochronological database on igneous rocks. To date, around 18,000 igneous rocks have been analysed across Queensland for chemical and/or age information. However, these data currently reside in a number of disparate datasets (e.g., Ozchron, Champion et al., 2007, Geological Survey of Queensland, journal publications, and unpublished university theses). The goal of this project is to collate and integrate these data on Queensland igneous rocks to improve our understanding of high heat producing granites in Queensland, in terms of their distribution (particularly in the subsurface), dimensions, ages, and controlling factors in their genesis.

The relationship between N2O, NO, and N2 fluxes from fertilized and irrigated dryland soils of the Aral Sea Basin, Uzbekistan

Microbial respiratory reduction of nitrous oxide (N2O) to dinitrogen (N2) via denitrification plays a key role within the global N-cycle since it is the most important process for converting reactive nitrogen back into inert molecular N2. However, due to methodological constraints, we still lack a comprehensive, quantitative understanding of denitrification rates and controlling factors across various ecosystems. We investigated N2, N2O and NO emissions from irrigated cotton fields within the Aral Sera Basin using the He/O2 atmosphere gas flow soil core technique and an incubation assay. NH4NO3 fertilizer, equivalent to 75 kg ha−1 and irrigation water, adjusting the water holding capacity to 70, 100 and 130% were applied to the incubation vessels to assess its influence on gaseous N emissions. Under soil conditions as they are naturally found after concomitant irrigation and fertilization, denitrification was the dominant process and N2 the main end product of denitrification. The mean ratios of N2/N2O emissions increased with increasing soil moisture content. N2 emissions exceeded N2O emissions by a factor of 5 ± 2 at 70% soil water holding capacity (WHC) and a factor of 55 ± 27 at 130% WHC. The mean ratios of N2O/NO emissions varied between 1.5 ± 0.4 (70% WHC) and 644 ± 108 (130% WHC). The magnitude of N2 emissions for irrigated cotton was estimated to be in the range of 24 ± 9 to 175 ± 65 kg-N ha−1season−1, while emissions of NO were only of minor importance (between 0.1 to 0.7 kg-N ha−1 season−1). The findings demonstrate that for irrigated dryland soils in the Aral Sera Basin, denitrification is a major pathway of N-loss and that substantial amounts of N-fertilizer are lost as N2 to the atmosphere for irrigated dryland soils.

Cultivation medium design via elemental balancing for tetraselmis suecica

The primary requirements for high-biomass-concentration microalgal cultivation include a photon source and distribution, efficient gas exchange and suitable growth medium composition. However, for mass outdoor production of microalgae, growth medium composition is a major controlling factor as most of the other factors such as light source and distribution are virtually uncontrollable. This work utilises an elemental balance approach between growth medium and biomass compositions to obtain high-density microalgal cultures in an open system. F medium, commonly used for the cultivation of marine microalgae such as Tetraselmis suecica was redesigned on the basis of increasing the biomass capacity of its major deficient components to support high biomass concentrations (τ ∼ 5.0 % for N, S and τ ∼ 10 % P), and the entire formulation was dissolved in 0.2 um sterile filtered natural seawater. Results show that the new medium (F') displayed a maximum biomass concentration and total lipid concentration of 1.29 g L 1 and 108.7 mg L 1 respectively, which represents over 2-fold increase compared to that of the F medium. Keeping all variables constant except growth medium, and using F medium as the base case of 1 medium cost (MC) unit mg -1 lipid, the F' medium yielded lipid at a cost of only 0.35 MC unit mg -1 lipids. These results show that greater amounts of biomass and lipids can be obtained more economically with minimal extra effort simply by using an optimised growth medium.

Computer analysis of impact behavior of concrete filled steel tube columns

This paper presents a numerical study of the response of axially loaded concrete filled steel tube (CFST) columns under lateral impact loading using explicit non-linear finite element techniques. The aims of this paper are to evaluate the vulnerability of existing columns to credible impact events as well as to contribute new information towards the safe design of such vulnerable columns. The model incorporates concrete confinement, strain rate effects of steel and concrete, contact between the steel tube and concrete and dynamic relaxation for pre-loading, which is a relatively recent method for applying a pre-loading in the explicit solver. The finite element model was first verified by comparing results with existing experimental results and then employed to conduct a parametric sensitivity analysis. The effects of various structural and load parameters on the impact response of the CFST column were evaluated to identify the key controlling factors. Overall, the major parameters which influence the impact response of the column are the steel tube thickness to diameter ratio, the slenderness ratio and the impact velocity. The findings of this study will enhance the current state of knowledge in this area and can serve as a benchmark reference for future analysis and design of CFST columns under lateral impact.

Numerical study on the surface depression of the concrete runway pavement under impact load

Airport runway pavement always subjected to huge impact loading due to the hard landing of aircraft on the pavement surface. Therefore runway pavements should have sufficient impact resistance capability to avoid damage causing by hard impact like surface deflection in downward or penetration since the repair works is cumbersome within the operating condition of airport and also increases the service life cost of the pavement structure. Several research works have been carried out on airport runway pavement to measure the present condition of pavement and also to predict future performance of it. However, most of the works are confined by pavement response under moving aircraft loading. Nevertheless, no comprehensive research work is yet conducted to identify the controlling factors which might have significant effect in changing the common pavements damage like surface penetration depth under impact of aircraft. Therefore, a 3D FE study is conducted to determine some effective factors in controlling the top surface penetration depth of runway pavement. Among the exterior factors, mass of the impactor, velocity of the impactor, impact angle and boundary conditions are selected and as interior factors, thickness of the runway pavement, compressive strength and density of materials used in the runway pavement are selected.

Environmental factors controlling soil respiration in three semiarid ecosystems

Previous research suggests that soil organic C pools may be a feature of semiarid regions that are particularly sensitive to climatic changes. We instituted an 18-mo experiment along an elevation gradient in northern Arizona to evaluate the influence of temperature, moisture, and soil C pool size on soil respiration. Soils, from underneath different free canopy types and interspaces of three semiarid ecosystems, were moved upslope and/or downslope to modify soil climate. Soils moved downslope experienced increased temperature and decreased precipitation, resulting in decreased soil moisture and soil respiration las much as 23 acid 20%, respectively). Soils moved upslope to more mesic, cooler sites had greater soil water content and increased rates of soil respiration las much as 40%), despite decreased temperature. Soil respiration rates normalized for total C were not significantly different within any of the three incubation sites, indicating that under identical climatic conditions, soil respiration is directly related to soil C pool size for the incubated soils. Normalized soil respiration rates between sites differed significantly for all soil types and were always greater for soils incubated under more mesic, but cooler, conditions. Total soil C did not change significantly during the experiment, but estimates suggest that significant portions of the rapidly cycling C pool were lost. While long-term decreases in aboveground and belowground detrital inputs may ultimately be greater than decreased soil respiration, the initial response to increased temperature and decreased precipitation in these systems is a decrease in annual soil C efflux.

Environmental factors controlling temporal and spatial variability in the soil-atmosphere exchange of CO2, CH4 and N2O from an Australian subtropical rainforest

The temporal variations in CO2, CH4 and N2O fluxes were measured over two consecutive years from February 2007 to March 2009 from a subtropical rainforest in south-eastern Queensland, Australia, using an automated sampling system. A concurrent study using an additional 30 manual chambers examined the spatial variability of emissions distributed across three nearby remnant rainforest sites with similar vegetation and climatic conditions. Interannual variation in fluxes of all gases over the 2 years was minimal, despite large discrepancies in rainfall, whereas a pronounced seasonal variation could only be observed for CO2 fluxes. High infiltration, drainage and subsequent high soil aeration under the rainforest limited N2O loss while promoting substantial CH4 uptake. The average annual N2O loss of 0.5 ± 0.1 kg N2O-N ha−1 over the 2-year measurement period was at the lower end of reported fluxes from rainforest soils. The rainforest soil functioned as a sink for atmospheric CH4 throughout the entire 2-year period, despite periods of substantial rainfall. A clear linear correlation between soil moisture and CH4 uptake was found. Rates of uptake ranged from greater than 15 g CH4-C ha−1 day−1 during extended dry periods to less than 2–5 g CH4-C ha−1 day−1 when soil water content was high. The calculated annual CH4 uptake at the site was 3.65 kg CH4-C ha−1 yr−1. This is amongst the highest reported for rainforest systems, reiterating the ability of aerated subtropical rainforests to act as substantial sinks of CH4. The spatial study showed N2O fluxes almost eight times higher, and CH4 uptake reduced by over one-third, as clay content of the rainforest soil increased from 12% to more than 23%. This demonstrates that for some rainforest ecosystems, soil texture and related water infiltration and drainage capacity constraints may play a more important role in controlling fluxes than either vegetation or seasonal variability

Psychosocial factors associated with controlling feeding practices of Indian and Australian-Indian mothers

This cross-sectional study examined the association between psychosocial factors (mothers’ perception of own and child weight, maternal self-efficacy in feeding and involvement of the mother-in-law in child-feeding) and controlling feeding practices (monitoring, restriction, pressure to eat and passive feeding). Participants were 531 affluent-Indian mothers in Australia and Mumbai with children aged 1-5 years. The psychosocial variables and feeding practices were measured using a combination of previously validated scales and study-developed items/scales. Multivariable regression analyses were stratified by sample (Australia and Mumbai) to investigate psychosocial factors related to the feeding practices, adjusting for covariates. Self-efficacy in feeding was associated with each of the feeding practices in at least one of the samples (β values between 0.1-0.2, p= 0.04-0.005). The greater involvement of the mother-in-law in child-feeding was related to the higher use of restriction in both samples (β values ≥0.2, p=0.02). In contrast, maternal weight perceptions were not consistently associated with feeding practices in either sample. The findings highlighted that unique (self-efficacy in feeding) and culturally-specific (involvement of the mother-in-law) variables not extensively researched within the context of child-feeding were important factors associated with Indian mothers’ feeding practices. Greater consideration of these factors may be required when tailoring child-feeding interventions for Indian mothers.

Factors affecting reproductive performance of the prawn, Penaeus monodon

The growth of the Penaeus monodon prawn aquaculture industry in Australia is hampered by a reliance on wild-caught broodstock. This species has proven difficult to breed from if broodstock are reared in captivity. Studies were therefore carried out to investigate factors controlling reproduction and influencing egg quality. Results of the studies revealed that patterns of nutrient accumulation during early ovary development are altered by captive conditions, possibly contributing to reduce larval quality. The sinus gland hormones were shown, together with the environment, to regulate two stages of ovary development. In a separate study it was further revealed that the hormone methyl farnesoate (MF) could negatively regulate the final stages of ovary development. Lastly it was shown that broodstock reared in captivity are less likely to mate and that this is due to inherent problems in both the male and the female prawns.

Factors influencing quality of life in patients with benign primary brain tumors : prior to and following surgery

Goals: Few studies have repeatedly evaluated quality of life and potentially relevant factors in patients with benign primary brain tumor. The purpose of this study was to explore the relationship between the experience of the symptom distress, functional status, depression, and quality of life prior to surgery (T1) and 1 month post-discharge (T2). ---------- Patients and methods: This was a prospective cohort study including 58 patients with benign primary brain tumor in one teaching hospital in the Taipei area of Taiwan. The research instruments included the M.D. Anderson Symptom Inventory, the Functional Independence Measure scale, the Hospital Depression Scale, and the Functional Assessment of Cancer Therapy-Brain.---------- Results: Symptom distress (T1: r=−0.90, p<0.01; T2: r=−0.52, p<0.01), functional status (T1: r=0.56, p<0.01), and depression (T1: r=−0.71, p<0.01) demonstrated a significant relationship with patients' quality of life. Multivariate analysis identified symptom distress (explained 80.2%, Rinc 2=0.802, p=0.001) and depression (explained 5.2%, Rinc 2=0.052, p<0.001) continued to have a significant independent influence on quality of life prior to surgery (T1) after controlling for key demographic and medical variables. Furthermore, only symptom distress (explained 27.1%, Rinc 2=0.271, p=0.001) continued to have a significant independent influence on quality of life at 1 month after discharge (T2).---------- Conclusions: The study highlights the potential importance of a patient's symptom distress on quality of life prior to and following surgery. Health professionals should inquire about symptom distress over time. Specific interventions for symptoms may improve the symptom impact on quality of life. Additional studies should evaluate symptom distress on longer-term quality of life of patients with benign brain tumor.

Intake of isoflavone and lignan phytoestrogens and associated demographic and lifestyle factors in older Australian women

The purpose was to determine intake of phytoestrogens in a sample of older Australian women, and to investigate associated lifestyle factors. Subjects were an age-stratified sample of 511 women aged 40-80 y, randomly selected from the electoral roll and participating in the Longitudinal Assessment of Ageing in Women at the Royal Brisbane and Women’s Hospital. A cross-sectional study was conducted to assess isoflavone and lignan intake over the past month from food and supplements using a 112-item phytoestrogen frequency questionnaire. Data were also collected on nutrient intakes, physical activity, smoking, alcohol, non-prescription supplements, hormone therapy, education and occupation. Logistic regression was used to evaluate associations between demographic and lifestyle variables and soy/linseed consumption while controlling for age. Isoflavone intakes were significantly higher in the younger compared to older age groups (p<0.001); there were no age-related differences in lignan intake. Forty-five percent of women consumed at least one serve of a soy and/or linseed item and were defined as a soy/linseed consumer. Median (range) intakes by consumers for isoflavones and lignans (3.9 (0-172) mg/d and 2.4 (0.1-33) mg/d) were higher than intakes by non-consumers (0.004 (0-2.6) mg/d and 1.57 (0.44-4.7) mg/d), respectively (p<0.001). Consumers had higher intakes of dietary fibre (p=0.003), energy (p=0.04) and polyunsaturated fat (p=0.004), and higher levels of physical activity (p=0.006), socio-economic position (p<0.001), education (p<0.001) and supplement use (p<0.001). Women who consumed soy or linseed foods differed in lifestyle and demographic characteristics suggesting these factors should be considered when investigating associations with chronic disease outcomes.

Risk factors for fatal crashes in rural Australia

This paper presents findings from the rural and remote road safety study, conducted in Queensland, Australia, from March 2004 till June 2007, and compares fatal crashes and non-fatal but serious crashes in respect of their environmental, vehicle and operator factors. During the study period there were 613 non-fatal crashes resulting in 684 hospitalised casualties and 119 fatal crashes resulting in 130 fatalities. Additional information from police sources was available on 103 fatal and 309 non-fatal serious crashes. Over three quarters of both fatal and hospitalised casualties were male and the median age in both groups was 34 years. Fatal crashes were more likely to involve speed, alcohol and violations of road rules and fatal crash victims were 2 and a 1/2 times more likely to be unrestrained inside the vehicle than non-fatal casualties, consistent with current international evidence. After controlling for human factors, vehicle and road conditions made a minimal contribution to the seriousness of the crash outcome. Targeted interventions to prevent fatalities on rural and remote roads should focus on reducing speed and drink driving and promoting seatbelt wearing.