180 resultados para Wood longitudinal modulus of elasticity
em Queensland University of Technology - ePrints Archive
Resumo:
In cold-formed steel construction, the use of a range of thin, high strength steels (0.35 mm thickness and 550 MPa yield stress) has increased significantly in recent times. A good knowledge of the basic mechanical properties of these steels is needed for a satisfactory use of them. In relation to the modulus of elasticity, the current practice is to assume it to be about 200 GPa for all steel grades. However, tensile tests of these steels have consistently shown that the modulus of elasticity varies with grade of steel and thickness. It was found that it increases to values as high as 240 GPa for smaller thicknesses and higher grades of steel. This paper discusses this topic, presents the tensile test results for a number of steel grades and thicknesses, and attempts to develop a relationship between modulus of elasticity, yield stress and thickness for the steel grades considered in this investigation.
Resumo:
Finite element models of bones can be created by deriving geometry from anx-ray CT scan. Material properties such as the elastic modulus can then be applied using either a single or set of homogeneous values, or individual elements can have local values mapped onto them. Values for the elastic modulus can be derived from the CT density values using an elasticityversus density relationship. Many elasticity–density relationships have been reported in the literature for human bone. However, while ovine in vivo models are common in orthopaedic research, no work has been done to date on creating FE models of ovine bones. To create these models and apply relevant material properties, an ovine elasticity-density relationship needs to be determined. Using fresh frozen ovine tibias the apparent density of regions of interest was determined from a clinical CT scan. The bones were the sectioned into cuboid samples of cortical bone from the regions of interest. Ultrasound was used to determine the elastic modulus in each of three directions – longitudinally, radially and tangentially. Samples then underwent traditional compression testing in each direction. The relationships between apparent density and both ultrasound, and compression modulus in each directionwere determined. Ultrasound testing was found to be a highly repeatable non-destructive method of calculating the elastic modulus, particularly suited to samples of this size. The elasticity-density relationships determined in the longitudinal direction were very similar between the compression and ultrasound data over the density range examined.A clear difference was seen in the elastic modulus between the longitudinal and transverse directions of the bone samples, and a transverse elasticity-density relationship is also reported.
Resumo:
There is strong evidence to show that beliefs about knowing and knowledge held by individuals (personal epistemologies) influence preservice teachers’ learning strategies and learning outcomes (Muis, 2004). However, we know very little about how preservice teachers’ personal epistemologies change as they progress through their teacher education programs. This study investigated changes in personal epistemology and beliefs about learning for a group of preservice teachers as they progressed through the four years of a Bachelor of Education degree. Preservice teachers completed the Epistemological Beliefs Survey (EBS, Kardash & Wood, 2000) when they commenced their course (Time 1) when they were in the 3rd year of their course (Time 2) and then again in the final year of their degree (Time 3). Findings indicated that there were significant changes in preservice teachers’ personal epistemologies between course entry and the final year of their course across all but one of the dimensions measured. Results are discussed in terms of the implications for teaching and teacher education.
Resumo:
The common goal of tissue engineering is to develop substitutes that can closely mimic the structure of extracellular matrix (ECM). However, similarly important is the intensive material properties which have often been overlooked, in particular, for soft tissues that are not to bear load assumingly. The mechanostructural properties determine not only the structural stability of biomaterials but also their physiological functionality by directing cellular activity and regulating cell fate decision. The aim here is to emphasize that cells could sense intensive material properties like elasticity and reside, proliferate, migrate and differentiate accordinglyno matter if the construct is from a natural source like cartilage, skin etc. or of synthetic one. Meanwhile, the very objective of this work is to provide a tunable scheme for manipulating the elasticity of collagen-based constructs to be used to demonstrate how to engineer cell behavior and regulate mechanotransduction. Articular cartilage was chosen as it represents one of the most complex hierarchical arrangements of collagen meshwork in both connective tissues and ECM-like biomaterials. Corona discharge treatment was used to produce constructs with varying density of crosslinked collagen and stiffness accordingly. The results demonstrated that elastic modulus increased up to 33% for samples treated up to one minute as crosslink density was found to increase with exposure time. According to the thermal analysis, longer exposure to corona increased crosslink density as the denaturation enthalpy increased. However the spectroscopy results suggested that despite the stabilization of the collagen structure the integrity of the triple helical structure remained intact. The in vitro superficial culture of heterologous chondrocytes also determined that the corona treatment can modulate migration with increased focal adhesion of cells due to enhanced stiffness, without cytotoxicity effects, and providing the basis for reinforcing three-dimensional collagen-based biomaterials in order to direct cell function and mediate mechanotransduction.
Resumo:
Purpose: In the present study, we consider mechanical properties of phosphate glasses under high temperatureinduced and under friction-induced cross-linking, which enhance the modulus of elasticity. Design/methodology/approach: Two nanomechanical properties are evaluated, the first parameter is the modulus of elasticity (E) (or Young's modulus) and the second parameter is the hardness (H). Zinc meta-, pyro - and orthophosphates were recognized as amorphous-colloidal nanoparticles were synthesized under laboratory conditions and showed antiwear properties in engine oil. Findings: Young's modulus of the phosphate glasses formed under high temperature was in the 60-89 GPa range. For phosphate tribofilm formed under friction hardness and the Young's modulus were in the range of 2-10 GPa and 40-215 GPa, respectively. The degree of cross-linking during friction is provided by internal pressure of about 600 MPa and temperature close to 1000°C enhancing mechanical properties by factor of 3 (see Fig 1). Research limitations/implications: The addition of iron or aluminum ions to phosphate glasses under high temperature - and friction-induced amorphization of zinc metaphosphate and pyrophosphate tends to provide more cross-linking and mechanically stronger structures. Iron and aluminum (FeO4 or AlO4 units), incorporated into phosphate structure as network formers, contribute to the anion network bonding by converting the P=O bonds into bridging oxygen. Future work should consider on development of new of materials prepared by solgel processes, eg., zinc (II)-silicic acid. Originality/value: This paper analyses the friction pressure-induced and temperature–induced the two factors lead phosphate tribofilm glasses to chemically advanced glass structures, which may enhance the wear inhibition. Adding the coordinating ions alters the pressure at which cross-linking occurs and increases the antiwear properties of the surface material significantly.
Resumo:
There have only been a small number of applications of consumer decision set theory to holiday destination choice, and these studies have tended to rely on a single cross sectional snapshot of research participants’ stated preferences. Very little has been reported on the relationship between stated destination preferences and actual travel, or changes in decision set composition over time. The paper presents a rare longitudinal examination of destination decision sets, in the context of short break holidays by car in Queensland, Australia. Two questionnaires were administered, three months apart. The first identified destination preferences while the second examined actual travel and revisited destination preferences. In relation to the conference theme, there was very little change in consumer preferences towards the competitive set of destinations over the three month period. A key implication for the destination of interest, which, in an attempt to change market perceptions, launched a new brand campaign during the period of the project, is that a long term investment in a consistent brand message will be required to change market perceptions. The results go some way to support the proposition that the positioning of a destination into a consumer’s decision set represents a source of competitive advantage.
Resumo:
Background Motivation has been identified as an area of difficulty for children with Down syndrome. Although individual differences in mastery motivation are presumed to have implications for subsequent competence, few longitudinal studies have addressed the stability of motivation and the predictive validity of early measures for later academic achievement, especially in atypical populations. Method The participants were 25 children with Down syndrome. Mastery motivation, operationalised as persistence, was measured in early childhood and adolescence using tasks and parent report. At the older age, preference for challenge, another aspect of mastery motivation, was also measured and the children completed assessments of academic competence. Results There were significant concurrent correlations among measures of persistence at both ages, and early task persistence was associated with later persistence. Persistence in early childhood was related to academic competence in adolescence, even when the effects of cognitive ability at the younger age were controlled. Conclusions For children with Down syndrome, persistence appears to be an individual characteristic that is relatively stable from early childhood to early adolescence. The finding that early mastery motivation is significant for later achievement has important implications for the focus of early interventions.
Psychological and social correlates of attrition in a longitudinal study of hazardous waste exposure
Resumo:
Benefit finding is a meaning making construct that has been shown to be related to adjustment in people with MS and their carers. This study investigated the dimensions, stability and potency of benefit finding in predicting adjustment over a 12 month interval using a newly developed Benefit Finding in Multiple Sclerosis Scale (BFiMSS). Usable data from 388 persons with MS and 232 carers was obtained from questionnaires completed at Time 1 and 12 months later (Time 2). Factor analysis of the BFiMSS revealed seven psychometrically sound factors: Compassion/Empathy, Spiritual Growth, Mindfulness, Family Relations Growth, Life Style Gains, Personal Growth, New Opportunities. BFiMSS total and factors showed satisfactory internal and retest reliability coefficients, and convergent, criterion and external validity. Results of regression analyses indicated that the Time 1 BFiMSS factors accounted for significant amounts of variance in each of the Time 2 adjustment outcomes (positive states of mind, positive affect, anxiety, depression) after controlling for Time 1 adjustment, and relevant demographic and illness variables. Findings delineate the dimensional structure of benefit finding in MS, the differential links between benefit finding dimensions and adjustment and the temporal unfolding of benefit finding in chronic illness.
Resumo:
Introduction: Weight gain is a common concern following breast cancer and has been associated with negative health outcomes. As such, prevention of weight gain is of clinical interest. This work describes weight change between 6- and 18-months following a breast cancer diagnosis and explores the personal, treatment and behavioural characteristics associated with gains in weight. Methods: Body mass index was objectively assessed, at three-monthly intervals, on a population-based sample of women newly diagnosed with unilateral breast cancer (n=185). Changes in BMI between 6- and 18-months post-diagnosis were calculated, with gains of one or more being considered clinically detrimental to future health. Results: Approximately 60% of participants were overweight or obese at 6-months post-diagnosis. While BMI remained relatively stable across the testing period (range=27.3-27.8), 24% of participants experienced clinically relevant gains in BMI (median gains=1.9). Following adjustment for potential confounders, younger age (<45 years; Odds ratio, OR=9.8), being morbidly obese at baseline (OR=4.6) and receiving hormone therapy (OR=4.8) were characteristics associated with an increased odds (p<0.05) of gaining BMI. Other characteristics associated with gains in BMI were more extensive surgery and having a history of smoking, although these relationships were not supported statistically. In contrast, caring for younger children was associated with reduced risk of gaining BMI (OR=0.3, p=0.20). Conclusions: Clinically relevant weight gain between 6- and 18-months post-breast cancer diagnosis is an issue for one in four women, with certain subgroups being particularly susceptible. However, the majority of women diagnosed with breast cancer are overweight or obese and gains in body weight are common. Thus, interventions that address the importance of achieving and sustaining a healthy body weight, delivered to all women with breast cancer, may have greater public health impact than interventions targeting any specific breast cancer subgroup.
Resumo:
A deconvolution method that combines nanoindentation and finite element analysis was developed to determine elastic modulus of thin coating layer in a coating-substrate bilayer system. In this method, the nanoindentation experiments were conducted to obtain the modulus of both the bilayer system and the substrate. The finite element analysis was then applied to deconvolve the elastic modulus of the coating. The results demonstrated that the elastic modulus obtained using the developed method was in good agreement with that reported in literature.
Resumo:
This report presents an analysis of the data from the first wave of the Longitudinal Study of Australian Children (LSAC) to explore the wellbeing of 5,107 children in the infant cohort of the study and the 4,983 children, aged 4 to 5 years, in the child cohort. Wave 1 of LSAC includes measures of multiple aspects of children’s early development. These developmental measures are summarised in the LSAC Outcome Index, a composite measure which includes an overall index as well as three separate domain scores, tapping physical development, social and emotional functioning, and learning and cognitive development.