Heavy vehicle suspensions : testing and analysis

Transport regulators consider that, with respect to pavement damage, heavy vehicles (HVs) are the riskiest vehicles on the road network. That HV suspension design contributes to road and bridge damage has been recognised for some decades. This thesis deals with some aspects of HV suspension characteristics, particularly (but not exclusively) air suspensions. This is in the areas of developing low-cost in-service heavy vehicle (HV) suspension testing, the effects of larger-than-industry-standard longitudinal air lines and the characteristics of on-board mass (OBM) systems for HVs. All these areas, whilst seemingly disparate, seek to inform the management of HVs, reduce of their impact on the network asset and/or provide a measurement mechanism for worn HV suspensions. A number of project management groups at the State and National level in Australia have been, and will be, presented with the results of the project that resulted in this thesis. This should serve to inform their activities applicable to this research. A number of HVs were tested for various characteristics. These tests were used to form a number of conclusions about HV suspension behaviours. Wheel forces from road test data were analysed. A “novel roughness” measure was developed and applied to the road test data to determine dynamic load sharing, amongst other research outcomes. Further, it was proposed that this approach could inform future development of pavement models incorporating roughness and peak wheel forces. Left/right variations in wheel forces and wheel force variations for different speeds were also presented. This led on to some conclusions regarding suspension and wheel force frequencies, their transmission to the pavement and repetitive wheel loads in the spatial domain. An improved method of determining dynamic load sharing was developed and presented. It used the correlation coefficient between two elements of a HV to determine dynamic load sharing. This was validated against a mature dynamic loadsharing metric, the dynamic load sharing coefficient (de Pont, 1997). This was the first time that the technique of measuring correlation between elements on a HV has been used for a test case vs. a control case for two different sized air lines. That dynamic load sharing was improved at the air springs was shown for the test case of the large longitudinal air lines. The statistically significant improvement in dynamic load sharing at the air springs from larger longitudinal air lines varied from approximately 30 percent to 80 percent. Dynamic load sharing at the wheels was improved only for low air line flow events for the test case of larger longitudinal air lines. Statistically significant improvements to some suspension metrics across the range of test speeds and “novel roughness” values were evident from the use of larger longitudinal air lines, but these were not uniform. Of note were improvements to suspension metrics involving peak dynamic forces ranging from below the error margin to approximately 24 percent. Abstract models of HV suspensions were developed from the results of some of the tests. Those models were used to propose further development of, and future directions of research into, further gains in HV dynamic load sharing. This was from alterations to currently available damping characteristics combined with implementation of large longitudinal air lines. In-service testing of HV suspensions was found to be possible within a documented range from below the error margin to an error of approximately 16 percent. These results were in comparison with either the manufacturer’s certified data or test results replicating the Australian standard for “road-friendly” HV suspensions, Vehicle Standards Bulletin 11. OBM accuracy testing and development of tamper evidence from OBM data were detailed for over 2000 individual data points across twelve test and control OBM systems from eight suppliers installed on eleven HVs. The results indicated that 95 percent of contemporary OBM systems available in Australia are accurate to +/- 500 kg. The total variation in OBM linearity, after three outliers in the data were removed, was 0.5 percent. A tamper indicator and other OBM metrics that could be used by jurisdictions to determine tamper events were developed and documented. That OBM systems could be used as one vector for in-service testing of HV suspensions was one of a number of synergies between the seemingly disparate streams of this project.

It’s about time : investing in transportation to keep Texas economically competitive : Appendices

APPENDIX A : PAVEMENT QUALITY (Zhanmin Zhang, Michael R. Murphy, Robert Harrison), 7 pages -- APPENDIX B : BRIDGE QUALITY (Jose Weissmann, Angela J. Weissmann), 6 pages -- APPENDIX C : URBAN TRAFFIC CONGESTION (Tim Lomax, David Schrank), 32 pages -- APPENDIX D: RURAL CORRIDORS (Tim Lomax, David Schrank), 6 pages -- APPENDIX E: ADDITIONAL REVENUE SOURCE OPTIONS FOR PAVEMENT AND BRIDGE MAINTENANCE (Mike Murphy, Seokho Chi, Randy Machemehl, Khali Persad, Robert Harrison, Zhanmin Zhang), 81 pages -- APPENDIX F: FUNDING TRANSPORTATION IMPROVEMENTS (David Ellis, Brianne Glover, Nick Norboge, Wally Crittenden), 19 pages -- APPENDIX G: ESTIMATING VEHICLE OPERATING COSTS AND PAVEMENT DETERIORATION (by Robert Harrison), 4 pages

Fatalism, superstition, religion, and culture : road user beliefs and behaviour in Pakistan

Road traffic crashes have emerged as a major health problem around the world. Road crash fatalities and injuries have been reduced significantly in developed countries, but they are still an issue in low and middle-income countries. The World Health Organization (WHO, 2009) estimates that the death toll from road crashes in low- and middle-income nations is more than 1 million people per year, or about 90% of the global road toll, even though these countries only account for 48% of the world's vehicles. Furthermore, it is estimated that approximately 265,000 people die every year in road crashes in South Asian countries and Pakistan stands out with 41,494 approximately deaths per year. Pakistan has the highest rate of fatalities per 100,000 population in the region and its road crash fatality rate of 25.3 per 100,000 population is more than three times that of Australia's. High numbers of road crashes not only cause pain and suffering to the population at large, but are also a serious drain on the country's economy, which Pakistan can ill-afford. Most studies identify human factors as the main set of contributing factors to road crashes, well ahead of road environment and vehicle factors. In developing countries especially, attention and resources are required in order to improve things such as vehicle roadworthiness and poor road infrastructure. However, attention to human factors is also critical. Human factors which contribute to crashes include high risk behaviours like speeding and drink driving, and neglect of protective behaviours such as helmet wearing and seat belt wearing. Much research has been devoted to the attitudes, beliefs and perceptions which contribute to these behaviours and omissions, in order to develop interventions aimed at increasing safer road use behaviours and thereby reducing crashes. However, less progress has been made in addressing human factors contributing to crashes in developing countries as compared to the many improvements in road environments and vehicle standards, and this is especially true of fatalistic beliefs and behaviours. This is a significant omission, since in different cultures in developing countries there are strong worldviews in which predestination persists as a central idea, i.e. that one's life (and death) and other events have been mapped out and are predetermined. Fatalism refers to a particular way in which people regard the events that occur in their lives, usually expressed as a belief that an individual does not have personal control over circumstances and that their lives are determined through a divine or powerful external agency (Hazen & Ehiri, 2006). These views are at odds with the dominant themes of modern health promotion movements, and present significant challenges for health advocates who aim to avert road crashes and diminish their consequences. The limited literature on fatalism reveals that it is not a simple concept, with religion, culture, superstition, experience, education and degree of perceived control of one's life all being implicated in accounts of fatalism. One distinction in the literature that seems promising is the distinction between empirical and theological fatalism, although there are areas of uncertainty about how well-defined the distinction between these types of fatalism is. Research into road safety in Pakistan is scarce, as is the case for other South Asian countries. From the review of the literature conducted, it is clear that the descriptions given of the different belief systems in developing countries including Pakistan are not entirely helpful for health promotion purposes and that further research is warranted on the influence of fatalism, superstition and other related beliefs in road safety. Based on the information available, a conceptual framework is developed as a means of structuring and focusing the research and analysis. The framework is focused on the influence of fatalism, superstition, religion and culture on beliefs about crashes and road user behaviour. Accordingly, this research aims to provide an understanding of the operation of fatalism and related beliefs in Pakistan to assist in the development and implementation of effective and culturally appropriate interventions. The research examines the influence of fatalism, superstition, religious and cultural beliefs on risky road use in Pakistan and is guided by three research questions: 1. What are the perceptions of road crash causation in Pakistan, in particular the role of fatalism, superstition, religious and cultural beliefs? 2. How does fatalism, superstition, and religious and cultural beliefs influence road user behaviour in Pakistan? 3. Do fatalism, superstition, and religious and cultural beliefs work as obstacles to road safety interventions in Pakistan? To address these questions, a qualitative research methodology was developed. The research focused on gathering data through individual in-depth interviewing using a semi-structured interview format. A sample of 30 participants was interviewed in Pakistan in the cities of Lahore, Rawalpindi and Islamabad. The participants included policy makers (with responsibility for traffic law), experienced police officers, religious orators, professional drivers (truck, bus and taxi) and general drivers selected through a combination of purposive, criterion and snowball sampling. The transcripts were translated from Urdu and analysed using a thematic analysis approach guided by the conceptual framework. The findings were divided into four areas: attribution of crash causation to fatalism; attribution of road crashes to beliefs about superstition and malicious acts; beliefs about road crash causation linked to popular concepts of religion; and implications for behaviour, safety and enforcement. Fatalism was almost universally evident, and expressed in a number of ways. Fate was used to rationalise fatal crashes using the argument that the people killed were destined to die that day, one way or another. Related to this was the sense of either not being fully in control of the vehicle, or not needing to take safety precautions, because crashes were predestined anyway. A variety of superstitious-based crash attributions and coping methods to deal with road crashes were also found, such as belief in the role of the evil eye in contributing to road crashes and the use of black magic by rivals or enemies as a crash cause. There were also beliefs related to popular conceptions of religion, such as the role of crashes as a test of life or a source of martyrdom. However, superstitions did not appear to be an alternative to religious beliefs. Fate appeared as the 'default attribution' for a crash when all other explanations failed to account for the incident. This pervasive belief was utilised to justify risky road use behaviour and to resist messages about preventive measures. There was a strong religious underpinning to the statement of fatalistic beliefs (this reflects popular conceptions of Islam rather than scholarly interpretations), but also an overlap with superstitious and other culturally and religious-based beliefs which have longer-standing roots in Pakistani culture. A particular issue which is explored in more detail is the way in which these beliefs and their interpretation within Pakistani society contributed to poor police reporting of crashes. The pervasive nature of fatalistic beliefs in Pakistan affects road user behaviour by supporting continued risk taking behaviour on the road, and by interfering with public health messages about behaviours which would reduce the risk of traffic crashes. The widespread influence of these beliefs on the ways that people respond to traffic crashes and the death of family members contribute to low crash reporting rates and to a system which appears difficult to change. Fate also appeared to be a major contributing factor to non-reporting of road crashes. There also appeared to be a relationship between police enforcement and (lack of) awareness of road rules. It also appears likely that beliefs can influence police work, especially in the case of road crash investigation and the development of strategies. It is anticipated that the findings could be used as a blueprint for the design of interventions aimed at influencing broad-spectrum health attitudes and practices among the communities where fatalism is prevalent. The findings have also identified aspects of beliefs that have complex social implications when designing and piloting driver intervention strategies. By understanding attitudes and behaviours related to fatalism, superstition and other related concepts, it should be possible to improve the education of general road users, such that they are less likely to attribute road crashes to chance, fate, or superstition. This study also underscores the understanding of this issue in high echelons of society (e.g., policy makers, senior police officers) as their role is vital in dispelling road users' misconceptions about the risks of road crashes. The promotion of an evidence or scientifically-based approach to road user behaviour and road safety is recommended, along with improved professional education for police and policy makers.

A road safety strategy for Norfolk Island, an Australian external territory

Norfolk Island is an Australian external territory in Oceania. The significant road safety reforms in Australia from the 1970s onward bypassed the island, and most road safety ‘silver bullets’ adopted in other Australian jurisdictions were not introduced. While legislative amendments in 2010 introduced mandatory seat belt wearing for vehicle occupants on Norfolk Island, other critical issues face the community including drink driving by residents and visitors, occupant protection for vehicle passengers, and the provision of a more protective road environment. The release of the first Norfolk Island road safety strategy 2014-2016 proposed, inter alia: • a lower BAC of 0.05 and the introduction of compulsory driver alcohol and drug testing by police; • targeted enforcement of occupant protection for vehicle passengers, particularly for passengers riding on vehicle tray backs; • education interventions to challenge values held by some members of the community that support unsafe road use; • ensuring that driver information, training and testing is adequate for all drivers; • identification and rectification of hazardous roadside infrastructure, particularly barrier protection at “high drop locations” within the road network; and • developing a specification for vehicle standards for vehicles imported into Norfolk Island. Norfolk Island is engaging in a process of integration with the Australian community, and wider issues relating to funding and resources have impacted on the implementation of the road safety strategy. The response to the strategy will be discussed, particularly in terms of current attempts to address drink driving and the provision of a safer road environment.

Lifecycle costs of ultracapacitors in electric vehicle applications

The pulse power characteristics of ultracapacitors appear well suited to electric vehicle applications, where they may supply the peak power more efficiently than the battery, and can prevent excessive over sizing of the battery pack due to peak power demands. Operation of ultracapacitors in battery electric vehicles is examined for possible improvements in system efficiency, vehicle driving range, battery pack lifetime, and potential reductions in system lifecycle cost. The lifecycle operation of these ultracapacitors is simulated using custom-built, dynamic simulation code constructed in Matlab. Despite apparent gains in system efficiency and driving range, the results strongly suggest that the inclusion of ultracapacitors in the electric vehicle does not make sense from a lifecycle cost perspective. Furthermore, a comparison with results from earlier work shows that this outcome is highly dependant upon the efficiency and cost of the battery under consideration. However, it is likely that the lifecycle cost benefits of ultracapacitors in these electric vehicles would be, at most, marginal and do not justify the additional capital costs and system complexity that would be incurred in the vehicle

Transport and health in China : recent collaborative research relating to vehicle factors and pollution

The nature of the transport system contributes to public health outcomes in a range of ways. The clearest contribution to public health is in the area of traffic crashes, because of their direct impact on individual death and disability and their direct costs to the health system. Other papers in this conference address these issues. This paper outlines some collaborative research between the Centre for Accident Research and Road Safety - Queensland (CARRS-Q) at QUT and Chinese researchers in areas that have indirect health impacts. Heavy vehicle dynamics: The integrity of the road surface influences crash risk, with ruts, pot-holes and other forms of road damage contributing to increased crash risks. The great majority of damage to the road surface from vehicles is caused by heavy trucks and buses, rather than cars or smaller vehicles. In some cases this damage is due to deliberate overloading, but in other cases it is due to vehicle suspension characteristics that lead to occasional high loads on particular wheels. Together with a visiting researcher and his colleagues, we have used both Queensland and Chinese data to model vehicle suspension systems that reduce the level of load, and hence the level of road damage and resulting crash risk(1-5). Toll worker exposure to vehicle emissions: The increasing construction of highways in China has also involved construction of a large number of toll roads. Tollbooth workers are potentially exposed to high levels of pollutants from vehicles, however the extent of this exposure and how it relates to standards for exposure are not well known. In a study led by a visiting researcher, we conducted a study to model these levels of exposure for a tollbooth in China(6). Noise pollution: The increasing presence of high speed roads in China has contributed to an increase in noise levels. In this collaborative study we modelled noise levels associated with a freeway widening near a university campus, and measures to reduce the noise(7). Along with these areas of research, there are many other areas of transport with health implications that are worthy of exploration. Traffic, noise and pollution contribute to a difficult environment for pedestrians, especially in an ageing society where there are health benefits to increasing physical activity. By building on collaborations such as those outlined, there is potential for a contribution to improved public health by addressing transport issues such as vehicle factors and pollution, and extending the research to other areas of travel activity. 1. Chen, Y., He, J., King, M., Chen, W. and Zhang, W. (2014). Stiffness-damping matching method of an ECAS system based on LQG control. Journal of Central South University, 21:439-446. DOI: 10.1007/s1177101419579 2. Chen, Y., He, J., King, M., Feng, Z. and Chang, W. (2013). Comparison of two suspension control strategies for multi-axle heavy truck. Journal of Central South University, 20(2): 550-562. 3. Chen, Y., He, J., King, M., Chen, W. and Zhang, W. (2013). Effect of driving conditions and suspension parameters on dynamic load-sharing of longitudinal-connected air suspensions. Science China Technological Sciences, 56(3): 666-676. DOI: 10.1007/s11431-012-5091-3 4. Chen, Y., He., J., King, M., Chen, W. and Zhang, W. (2013). Model development and dynamic load-sharing analysis of longitudinal-connected air suspensions. Strojniški Vestnik - Journal of Mechanical Engineering, 59(1):14-24. 5. Chen, Y., He, J., King, M., Liu, H. and Zhang, W. (2013). Dynamic load-sharing of longitudinal-connected air suspensions of a tri-axle semi-trailer. Proceedings of Transportation Research Board Annual Conference, Washington DC, 13-17 January 2013, paper no. 13-1117. 6. He, J., Qi, Z., Hang, W., King, M., and Zhao, C. (2011). Numerical evaluation of pollutant dispersion at a toll plaza based on system dynamics and Computational Fluid Dynamics models. Transportation Research Part C, 19(2011):510-520. 7. Zhang, C., He, J., Wang, Z., Yin, R. and King, M. (2013). Assessment of traffic noise level before and after freeway widening using traffic microsimulation and a refined classic noise prediction method. Proceedings of Transportation Research Board Annual Conference, Washington DC, 13-17 January 2013, paper no. 13-2016.

Vision, functional and cognitive determinants of motor vehicle incidents in older drivers

Background: The proportion of older individuals in the driving population is predicted to increase in the next 50 years. This has important implications for driving safety as abilities which are important for safe driving, such as vision (which accounts for the majority of the sensory input required for driving), processing ability and cognition have been shown to decline with age. The current methods employed for screening older drivers upon re-licensure are also vision based. This study, which investigated social, behavioural and professional aspects involved with older drivers, aimed to determine: (i) if the current visual standards in place for testing upon re-licensure are effective in reducing the older driver fatality rate in Australia; (ii) if the recommended visual standards are actually implemented as part of the testing procedures by Australian optometrists; and (iii) if there are other non-standardised tests which may be better at predicting the on-road incident-risk (including near misses and minor incidents) in older drivers than those tests recommended in the standards. Methods: For the first phase of the study, state-based age- and gender-stratified numbers of older driver fatalities for 2000-2003 were obtained from the Australian Transportation Safety Bureau database. Poisson regression analyses of fatality rates were considered by renewal frequency and jurisdiction (as separate models), adjusting for possible confounding variables of age, gender and year. For the second phase, all practising optometrists in Australia were surveyed on the vision tests they conduct in consultations relating to driving and their knowledge of vision requirements for older drivers. Finally, for the third phase of the study to investigate determinants of on-road incident risk, a stratified random sample of 600 Brisbane residents aged 60 years and were selected and invited to participate using an introductory letter explaining the project requirements. In order to capture the number and type of road incidents which occurred for each participant over 12 months (including near misses and minor incidents), an important component of the prospective research study was the development and validation of a driving diary. The diary was a tool in which incidents that occurred could be logged at that time (or very close in time to which they occurred) and thus, in comparison with relying on participant memory over time, recall bias of incident occurrence was minimised. Association between all visual tests, cognition and scores obtained for non-standard functional tests with retrospective and prospective incident occurrence was investigated. Results: In the first phase,rivers aged 60-69 years had a 33% lower fatality risk (Rate Ratio [RR] = 0.75, 95% CI 0.32-1.77) in states with vision testing upon re-licensure compared with states with no vision testing upon re-licensure, however, because the CIs are wide, crossing 1.00, this result should be regarded with caution. However, overall fatality rates and fatality rates for those aged 70 years and older (RR=1.17, CI 0.64-2.13) did not differ between states with and without license renewal procedures, indicating no apparent benefit in vision testing legislation. For the second phase of the study, nearly all optometrists measured visual acuity (VA) as part of a vision assessment for re-licensing, however, 20% of optometrists did not perform any visual field (VF) testing and only 20% routinely performed automated VF on older drivers, despite the standards for licensing advocating automated VF as part of the vision standard. This demonstrates the need for more effective communication between the policy makers and those responsible for carrying out the standards. It may also indicate that the overall higher driver fatality rate in jurisdictions with vision testing requirements is resultant as the tests recommended by the standards are only partially being conducted by optometrists. Hence a standardised protocol for the screening of older drivers for re-licensure across the nation must be established. The opinions of Australian optometrists with regard to the responsibility of reporting older drivers who fail to meet the licensing standards highlighted the conflict between maintaining patient confidentiality or upholding public safety. Mandatory reporting requirements of those drivers who fail to reach the standards necessary for driving would minimise potential conflict between the patient and their practitioner, and help maintain patient trust and goodwill. The final phase of the PhD program investigated the efficacy of vision, functional and cognitive tests to discriminate between at-risk and safe older drivers. Nearly 80% of the participants experienced an incident of some form over the prospective 12 months, with the total incident rate being 4.65/10 000 km. Sixty-three percent reported having a near miss and 28% had a minor incident. The results from the prospective diary study indicate that the current vision screening tests (VA and VF) used for re-licensure do not accurately predict older drivers who are at increased odds of having an on-road incident. However, the variation in visual measurements of the cohort was narrow, also affecting the results seen with the visual functon questionnaires. Hence a larger cohort with greater variability should be considered for a future study. A slightly lower cognitive level (as measured with the Mini-Mental State Examination [MMSE]) did show an association with incident involvement as did slower reaction time (RT), however the Useful-Field-of-View (UFOV) provided the most compelling results of the study. Cut-off values of UFOV processing (>23.3ms), divided attention (>113ms), selective attention (>258ms) and overall score (moderate/ high/ very high risk) were effective in determining older drivers at increased odds of having any on-road incident and the occurrence of minor incidents. Discussion: The results have shown that for the 60-69 year age-group, there is a potential benefit in testing vision upon licence renewal. However, overall fatality rates and fatality rates for those aged 70 years and older indicated no benefit in vision testing legislation and suggests a need for inclusion of screening tests which better predict on-road incidents. Although VA is routinely performed by Australian optometrists on older drivers renewing their licence, VF is not. Therefore there is a need for a protocol to be developed and administered which would result in standardised methods conducted throughout the nation for the screening of older drivers upon re-licensure. Communication between the community, policy makers and those conducting the protocol should be maximised. By implementing a standardised screening protocol which incorporates a level of mandatory reporting by the practitioner, the ethical dilemma of breaching patient confidentiality would also be resolved. The tests which should be included in this screening protocol, however, cannot solely be ones which have been implemented in the past. In this investigation, RT, MMSE and UFOV were shown to be better determinants of on-road incidents in older drivers than VA and VF, however, as previously mentioned, there was a lack of variability in visual status within the cohort. Nevertheless, it is the recommendation from this investigation, that subject to appropriate sensitivity and specificity being demonstrated in the future using a cohort with wider variation in vision, functional performance and cognition, these tests of cognition and information processing should be added to the current protocol for the screening of older drivers which may be conducted at licensing centres across the nation.

In-vehicle avatars to elicit social response and change driving behaviour

Social and psychological theories have provided a plethora of evidence showing that the physical difficulty to express appropriate social interactions between drivers expresses itself in aggression, selfish driving and anti-social behaviour. Therefore there is a need to improve interactions between drivers and allow clearer collective decision making between them. Personal characteristics and the driving situations play strong roles in driver’s aggression. Our approach is centered around the driving situation as opposed to focusing on personality characteristics. It examines aggression and manipulates contextual variables such as driver’s eye contact exchanges. This paper presents a new unobtrusive in-vehicle system that aims at communicating drivers’ intentions, elicit social responses and increasing mutual awareness. It uses eye gaze as a social cue to affect collective decision making with the view to contribute to safe driving. The authors used a driving simulator to design a case control experiment in which eye gaze movements are conveyed with an avatar. Participants were asked to drive through different types of intersections. An avatar representing the head of the other driver was displayed and driver behaviour was analysed. Significant eye gaze pattern difference where observed when an avatar was displayed. Drivers cautiously refer to the avatar when information is required on the intention of others (e.g. when they do not have the right of way). The majority of participants reported the perception of “being looked at”. The number of glances and time spent gazing at the avatar did not indicate an unsafe distraction by standards of in-vehicle device ergonomic design. Avatars were visually consulted primarily in less demanding driving situations, which underlines their non-distractive nature.

Introducing action research as a vehicle to bring about change to a psychiatric nursing curriculum in Taiwan

The focus of this study is on curriculum change within a School of Nursing in Taiwan where there is a growing demand for educational reform in order to meet the new accreditation standards and demands of the Taiwan Nursing Accreditation Council (TNAC). The aim of this study was to transform the Psychiatric Nursing curriculum in ways that are empowering, generative and sustainable. This study introduced Action Research as a vehicle to bring about curriculum transformation. I conceptualised a framework to guide the transformation process based on the notions of learner-centredness, conceptual change, pedagogical knowledge, reflection, collaboration, reculturing and empowerment. The Action Plan was developed in accordance with the conceptual framework, and was developed in five steps through which team members explored and became aware of our conceptions of teaching and learning, and then planned and implemented actions to change our curriculum, and examined and reflected on the curriculum transformation. The study demonstrated the value of working collaboratively to solve educational problems. This study also suggested that experiential knowledge, when shared and integrated with theoretical knowledge, can constructively contribute to all aspects of curriculum transformation. This study further supported the value of including clinical facilitators in the development and transformation of curricula. It confirmed that academics and clinical facilitators can work together to create new learning for students. This study is significant for both practical and political reasons. Its practical significance lies in its direct utility to the learners and teachers who were involved in the study. The political significance lies in the potential of the study to lead to further changes or improvements in other, similar contexts. The study is limited in that any interpretations cannot be generalised to other contexts. However, what emerged adds to the body of knowledge in such a way that it would constitute the basis for better informed educational practice.

Experimental studies of wireless communication and GNSS kinematic positioning performance in high-mobility vehicle environments

In order to support intelligent transportation system (ITS) road safety applications such as collision avoidance, lane departure warnings and lane keeping, Global Navigation Satellite Systems (GNSS) based vehicle positioning system has to provide lane-level (0.5 to 1 m) or even in-lane-level (0.1 to 0.3 m) accurate and reliable positioning information to vehicle users. However, current vehicle navigation systems equipped with a single frequency GPS receiver can only provide road-level accuracy at 5-10 meters. The positioning accuracy can be improved to sub-meter or higher with the augmented GNSS techniques such as Real Time Kinematic (RTK) and Precise Point Positioning (PPP) which have been traditionally used in land surveying and or in slowly moving environment. In these techniques, GNSS corrections data generated from a local or regional or global network of GNSS ground stations are broadcast to the users via various communication data links, mostly 3G cellular networks and communication satellites. This research aimed to investigate the precise positioning system performances when operating in the high mobility environments. This involves evaluation of the performances of both RTK and PPP techniques using: i) the state-of-art dual frequency GPS receiver; and ii) low-cost single frequency GNSS receiver. Additionally, this research evaluates the effectiveness of several operational strategies in reducing the load on data communication networks due to correction data transmission, which may be problematic for the future wide-area ITS services deployment. These strategies include the use of different data transmission protocols, different correction data format standards, and correction data transmission at the less-frequent interval. A series of field experiments were designed and conducted for each research task. Firstly, the performances of RTK and PPP techniques were evaluated in both static and kinematic (highway with speed exceed 80km) experiments. RTK solutions achieved the RMS precision of 0.09 to 0.2 meter accuracy in static and 0.2 to 0.3 meter in kinematic tests, while PPP reported 0.5 to 1.5 meters in static and 1 to 1.8 meter in kinematic tests by using the RTKlib software. These RMS precision values could be further improved if the better RTK and PPP algorithms are adopted. The tests results also showed that RTK may be more suitable in the lane-level accuracy vehicle positioning. The professional grade (dual frequency) and mass-market grade (single frequency) GNSS receivers were tested for their performance using RTK in static and kinematic modes. The analysis has shown that mass-market grade receivers provide the good solution continuity, although the overall positioning accuracy is worse than the professional grade receivers. In an attempt to reduce the load on data communication network, we firstly evaluate the use of different correction data format standards, namely RTCM version 2.x and RTCM version 3.0 format. A 24 hours transmission test was conducted to compare the network throughput. The results have shown that 66% of network throughput reduction can be achieved by using the newer RTCM version 3.0, comparing to the older RTCM version 2.x format. Secondly, experiments were conducted to examine the use of two data transmission protocols, TCP and UDP, for correction data transmission through the Telstra 3G cellular network. The performance of each transmission method was analysed in terms of packet transmission latency, packet dropout, packet throughput, packet retransmission rate etc. The overall network throughput and latency of UDP data transmission are 76.5% and 83.6% of TCP data transmission, while the overall accuracy of positioning solutions remains in the same level. Additionally, due to the nature of UDP transmission, it is also found that 0.17% of UDP packets were lost during the kinematic tests, but this loss doesn't lead to significant reduction of the quality of positioning results. The experimental results from the static and the kinematic field tests have also shown that the mobile network communication may be blocked for a couple of seconds, but the positioning solutions can be kept at the required accuracy level by setting of the Age of Differential. Finally, we investigate the effects of using less-frequent correction data (transmitted at 1, 5, 10, 15, 20, 30 and 60 seconds interval) on the precise positioning system. As the time interval increasing, the percentage of ambiguity fixed solutions gradually decreases, while the positioning error increases from 0.1 to 0.5 meter. The results showed the position accuracy could still be kept at the in-lane-level (0.1 to 0.3 m) when using up to 20 seconds interval correction data transmission.

An exploration of the maturity model concept as a vehicle for higher education institutions to assess their capability to address student engagement : a work in progress

Gaining a competitive edge in the area of the engagement, success and retention of commencing students is a significant issue in higher education, made more so currently because of the considerable and increasing pressure on teaching and learning from the new standards framework and performance funding. This paper introduces the concept of maturity models (MMs) and their application to assessing the capability of higher education institutions (HEIs) to address student engagement, success and retention (SESR). A concise description of the features of maturity models is presented with reference to an SESR-MM currently being developed. The SESR-MM is proposed as a viable instrument for assisting HEIs in the management and improvement of their SESR activities.

Commercial vehicle pre-clearance programs : current issues and recommendations for potential implementation

The regulation of overweight trucks is of increasing importance. Quickly growing heavy vehicle volumes over-proportionally contribute to roadway damage. Raising maintenance costs and compromised road safety are also becoming a major concern to managing agencies. Minimizing pavement wear is done by regulating overloaded trucks on major highways at weigh stations. However, due to lengthy inspections and insufficient capacities, weigh stations tend to be inefficient. New practices, using Radio Frequency Identification (RFID) transponders and weigh-in-motion technologies, called preclearance programs, have been set up in a number of countries. The primary aim of this study is to investigate the current issues with regard to the implementation and operation of the preclearance program. The State of Queensland, Australia, is used as a case study. The investigation focuses on three aspects; the first emphasizes on identifying the need for improvement of the current regulation programs in Queensland. Second, the operators of existing preclearance programs are interviewed for their lessons-learned and the marketing strategies used for promoting their programs. The trucking companies in Queensland are interviewed for their experiences with the current weighing practices and attitudes toward the potential preclearance system. Finally, the estimated benefit of the preclearance program deployment in Queensland is analyzed. The penultimate part brings the former four parts together and provides the study findings and recommendations. The framework and study findings could be valuable inputs for other roadway agencies considering a similar preclearance program or looking to promote their existing ones.

Estimating health related costs and savings from balcony acoustic design for road traffic noise

A multi-faceted study is conducted with the objective of estimating the potential fiscal savings in annoyance and sleep disturbance related health costs due to providing improved building acoustic design standards. This study uses balcony acoustic treatments in response to road traffic noise as an example. The study area is the State of Queensland in Australia, where regional road traffic noise mapping data is used in conjunction with standard dose–response curves to estimate the population exposure levels. The background and the importance of using the selected road traffic noise indicators are discussed. In order to achieve the objective, correlations between the mapping indicator (LA10 (18 hour)) and the dose response curve indicators (Lden and Lnight) are established via analysis on a large database of road traffic noise measurement data. The existing noise exposure of the study area is used to estimate the fiscal reductions in health related costs through the application of simple estimations of costs per person per year per degree of annoyance or sleep disturbance. The results demonstrate that balcony acoustic treatments may provide a significant benefit towards reducing the health related costs of road traffic noise in a community.