Alkaline hydrothermal treatment of titanate nanostructures

Since its initial proposal in 1998, alkaline hydrothermal processing has rapidly become an established technology for the production of titanate nanostructures. This simple, highly reproducible process has gained a strong research following since its conception. However, complete understanding and elucidation of nanostructure phase and formation have not yet been achieved. Without fully understanding phase, formation, and other important competing effects of the synthesis parameters on the final structure, the maximum potential of these nanostructures cannot be obtained. Therefore this study examined the influence of synthesis parameters on the formation of titanate nanostructures produced by alkaline hydrothermal treatment. The parameters included alkaline concentration, hydrothermal temperature, the precursor material‘s crystallite size and also the phase of the titanium dioxide precursor (TiO2, or titania). The nanostructure‘s phase and morphology was analysed using X-ray diffraction (XRD), Raman spectroscopy and transmission electron microscopy. X-ray photoelectron spectroscopy (XPS), dynamic light scattering (non-invasive backscattering), nitrogen sorption, and Rietveld analysis were used to determine phase, for particle sizing, surface area determinations, and establishing phase concentrations, respectively. This project rigorously examined the effect of alkaline concentration and hydrothermal temperature on three commercially sourced and two self-prepared TiO2 powders. These precursors consisted of both pure- or mixed-phase anatase and rutile polymorphs, and were selected to cover a range of phase concentrations and crystallite sizes. Typically, these precursors were treated with 5–10 M sodium hydroxide (NaOH) solutions at temperatures between 100–220 °C. Both nanotube and nanoribbon morphologies could be produced depending on the combination of these hydrothermal conditions. Both titania and titanate phases are comprised of TiO6 units which are assembled in different combinations. The arrangement of these atoms affects the binding energy between the Ti–O bonds. Raman spectroscopy and XPS were therefore employed in a preliminary study of phase determination for these materials. The change in binding energy from a titania to a titanate binding energy was investigated in this study, and the transformation of titania precursor into nanotubes and titanate nanoribbons was directly observed by these methods. Evaluation of the Raman and XPS results indicated a strengthening in the binding energies of both the Ti (2p3/2) and O (1s) bands which correlated to an increase in strength and decrease in resolution of the characteristic nanotube doublet observed between 320 and 220 cm.1 in the Raman spectra of these products. The effect of phase and crystallite size on nanotube formation was examined over a series of temperatures (100.200 �‹C in 20 �‹C increments) at a set alkaline concentration (7.5 M NaOH). These parameters were investigated by employing both pure- and mixed- phase precursors of anatase and rutile. This study indicated that both the crystallite size and phase affect nanotube formation, with rutile requiring a greater driving force (essentially �\harsher. hydrothermal conditions) than anatase to form nanotubes, where larger crystallites forms of the precursor also appeared to impede nanotube formation slightly. These parameters were further examined in later studies. The influence of alkaline concentration and hydrothermal temperature were systematically examined for the transformation of Degussa P25 into nanotubes and nanoribbons, and exact conditions for nanostructure synthesis were determined. Correlation of these data sets resulted in the construction of a morphological phase diagram, which is an effective reference for nanostructure formation. This morphological phase diagram effectively provides a .recipe book�e for the formation of titanate nanostructures. Morphological phase diagrams were also constructed for larger, near phase-pure anatase and rutile precursors, to further investigate the influence of hydrothermal reaction parameters on the formation of titanate nanotubes and nanoribbons. The effects of alkaline concentration, hydrothermal temperature, crystallite phase and size are observed when the three morphological phase diagrams are compared. Through the analysis of these results it was determined that alkaline concentration and hydrothermal temperature affect nanotube and nanoribbon formation independently through a complex relationship, where nanotubes are primarily affected by temperature, whilst nanoribbons are strongly influenced by alkaline concentration. Crystallite size and phase also affected the nanostructure formation. Smaller precursor crystallites formed nanostructures at reduced hydrothermal temperature, and rutile displayed a slower rate of precursor consumption compared to anatase, with incomplete conversion observed for most hydrothermal conditions. The incomplete conversion of rutile into nanotubes was examined in detail in the final study. This study selectively examined the kinetics of precursor dissolution in order to understand why rutile incompletely converted. This was achieved by selecting a single hydrothermal condition (9 M NaOH, 160 °C) where nanotubes are known to form from both anatase and rutile, where the synthesis was quenched after 2, 4, 8, 16 and 32 hours. The influence of precursor phase on nanostructure formation was explicitly determined to be due to different dissolution kinetics; where anatase exhibited zero-order dissolution and rutile second-order. This difference in kinetic order cannot be simply explained by the variation in crystallite size, as the inherent surface areas of the two precursors were determined to have first-order relationships with time. Therefore, the crystallite size (and inherent surface area) does not affect the overall kinetic order of dissolution; rather, it determines the rate of reaction. Finally, nanostructure formation was found to be controlled by the availability of dissolved titanium (Ti4+) species in solution, which is mediated by the dissolution kinetics of the precursor.

Self-management of cancer treatment-related fatigue, nausea, vomiting and oral mucositis in Chinese cancer patients

Background: Treatment-related symptoms continue to place a significant burden on many cancer patients. Many side effects require patients to engage in a range of self-management actions. While some studies have explored self-management of treatment-related side effects in Western settings, very few studies were identified that described the self-management practices of cancer patients in China. Objective: The purposes of this study are to: (1) Investigate Chinese cancer patients. self-management behaviours in dealing with the fatigue, nausea/vomiting and oral mucositis that result from treatment, as well as the perceived effectiveness of these behaviours and related self-efficacy in performing them. (2) Explore factors influencing symptom self-management behaviours using the Cancer Symptom Self-management Framework based on Grey, Knafl and McCorkle.s (2006) self-management framework as a guide. Methods: This study was divided into two phases. Phase One consisted of the translation and modification of two instruments. The adaptation of these instruments to ensure applicability in the Chinese context was achieved through semi-structured interviews with six cancer patients, and content evaluation with eight experienced oncology nurses. A pilot study was conducted with nine cancer patients to trial the questionnaire set in the Chinese context. Based on the results of Phase One, Phase Two involved a cross-sectional survey of Chinese cancer patients undergoing cancer treatment using these instruments. A total of 277 chemotherapy patients with fatigue and/or nausea and vomiting, and 100 radiotherapy patients with oral mucositis were surveyed. Results: Participants in this study reported a variety of self-management behaviours to cope with fatigue, nausea, vomiting and oral mucositis. There are some consistencies as well disparities between strategies that are frequently used and those rated as effective. For fatigue self-management, participants were more likely to use strategies related to rest and sleep, while activity enhancement strategies were rated as achieving higher relief. For nausea and vomiting self-management, dietary modification and taking medication were most frequently used and rated as moderately effective. Psychological strategies were used by more than a third of participants and were rated as mildly effective. Some other infrequently used strategies, such as distraction by keeping busy and acupressure, were rated as moderately effective. For oral mucositis self-management, having soft, bland food and keeping the mouth moisturised were most frequently reported and they were rated as achieving moderate relief. A prescribed mouthwash was used by most but not all participants and brought moderate relief. In general, patients had low-to-moderate self-efficacy in nausea and vomiting self-management behaviours, moderate self-efficacy in fatigue self-management behaviours, and low-to-moderate self-efficacy in oral mucositis self-management behaviours. In terms of the factors influencing symptom self-management, different predictors were identified affecting engagement in fatigue, nausea/vomiting and oral mucositis self-management behaviours. Self-efficacy scores of different behaviours were consistently found to be a positive predictor of the relief level from corresponding behaviours, after controlling for other variables. Perceived social support from health care professionals was identified as an important factor influencing nausea and vomiting self-management behaviours, while neighbourhood support was important for fatigue self-management. In addition, symptom distress was identified as an important factor influencing nausea and vomiting self-management. Conclusion: Similar to reports from overseas, Chinese cancer patients initiate a wide range of self-management behaviours in response to treatment-related side effects. While some behaviours were reported to provide relief, many did not. Given these results, this study has a number of practical implications for health care professionals, particularly in relation to developing tailored self-management programs for fatigue, nausea, vomiting and oral mucositis. Additionally, this study suggests a number of theoretical implications and directions for future research. It is envisaged that these recommendations may pave the way for further studies understanding and promoting cancer symptom self-management in Chinese people affected by cancer.

Metacognitive narrative psychotherapy for people diagnosed with schizophrenia : an outline of a principle-based treatment manual

Schizophrenia is often characterised by diminished self-experience. This article describes the development and principles of a manual for a psychotherapeutic treatment model that aims to enhance self-experience in people diagnosed with schizophrenia. Metacognitive Narrative Psychotherapy draws upon dialogical theory of self and the work of Lysaker and colleagues, in conjunction with narrative principles of therapy as operationalised by Vromans. To date, no manual for a metacognitive narrative approach to the treatment of schizophrenia exists. After a brief description of narrative understandings of schizophrenia, the development of the manual is described. Five general phases of treatment are outlined: (1) developing a therapeutic relationship; (2) eliciting narratives; (3) enhancing metacognitive capacity; (4) enriching narratives, and; (5) living enriched narratives. Proscribed practices are also described. Examples of therapeutic interventions and dialogue are provided to further explain the application of interventions in-session. The manual has been piloted in a study investigating the effectiveness of Metacognitive Narrative Psychotherapy in the treatment of people diagnosed with schizophrenia spectrum disorders.

Stabilization of stormwater biofilters: Impacts of wetting and drying phases and the addition of organic matter to filter media

Ripening period refers to a phase of stabilization in sand filters in water treatment systems that follows a new installation or cleaning of the filter. Intermittent wetting and drying, a unique property of stormwater biofilters, would similarly be subjected to a phase of stabilization. Suspended solids, is an important parameter that is often used to monitor the stabilization of sand filters in water treatment systems. Stormwater biofilters however, contain organic material that is added to the filter layer to enhance nitrate removal, the dynamics of which is seldom analysed in stabilization of stormwater biofilters. Therefore, in this study of stormwater biofiltration in addition to suspended solids (Turbidity), organic matter (TOC, DOC, TN and TKN) was also monitored as a parameter for stabilization of the stormwater biofilter. One Perspex bioretention column (94 mm internal diameter) was fabricated with filter layer that contained 8% organic material and fed with tapwater with different antecedent dry days (0 – 40 day) at 100 mL/min. Samples were collected from the outflow at different time intervals between 2 – 150 minutes and were tested for Total Organic Carbon, Dissolved Organic Carbon, Total Nitrogen, Total Kjeldhal Nitrogen and Turbidity. The column was observed to experience two phases of stabilization, one at the beginning of each event that lasted for 30 minutes while the other phase was observed across subsequent events that related to the age of filter.

Mechanochemical treatment of kaolinite

Kaolinite surfaces were modified by mechanochemical treatment for periods of time up to 10 h. X-ray diffraction shows a steady decrease in intensity of the d(001) spacing with mechanochemical treatment, resulting in the delamination of the kaolinite and a subsequent decrease in crystallite size with grinding time. Thermogravimetric analyses show the dehydroxylation patterns of kaolinite are significantly modified. Changes in the molecular structure of the kaolinite surface hydroxyls were followed by infrared spectroscopy. Hydroxyls were lost after 10 h of grinding as evidenced by a decrease in intensity of the OH stretching vibrations at 3695 and 3619 cm−1 and the deformation modes at 937 and 915 cm−1. Concomitantly an increase in the hydroxyl stretching vibrations of water is found. The water-bending mode was observed at 1650 cm−1, indicating that water is coordinating to the modified kaolinite surface. Changes in the surface structure of the OSiO units were reflected in the SiO stretching and OSiO bending vibrations. The decrease in intensity of the 1056 and 1034 cm−1 bands attributed to kaolinite SiO stretching vibrations were concomitantly matched by the increase in intensity of additional bands at 1113 and 520 cm−1 ascribed to the new mechanically synthesized kaolinite surface. Mechanochemical treatment of the kaolinite results in a new surface structure.

Thermal treatment of weddellite—a Raman and infrared emission spectroscopic study

Thermal transformations of natural calcium oxalate dihydrate known in mineralogy as weddellite have been undertaken using a combination of Raman microscopy and infrared emission spectroscopy. The vibrational spectroscopic data was complimented with high resolution thermogravimetric analysis combined with evolved gas mass spectrometry. TG–MS identified three mass loss steps at 114, 422 and 592 °C. In the first mass loss step water is evolved only, in the second and third steps carbon dioxide is evolved. The combination of Raman microscopy and a thermal stage clearly identifies the changes in the molecular structure with thermal treatment. Weddellite is the phase in the temperature range up to the pre-dehydration temperature of 97 °C. At this temperature, the phase formed is whewellite (calcium oxalate monohydrate) and above 114 °C the phase is the anhydrous calcium oxalate. Above 422 °C, calcium carbonate is formed. Infrared emission spectroscopy shows that this mineral decomposes at around 650 °C. Changes in the position and intensity of the C=O and C---C stretching vibrations in the Raman spectra indicate the temperature range at which these phase changes occur.

Understanding the Main Phases of Developing a Maturity Assessment Model

Practitioners and academics have developed numerous maturity models for many domains in order to measure competency. These initiatives have often been influenced by the Capability Maturity Model. However, an accumulative effort has not been made to generalize the phases of developing a maturity model in any domain. This paper proposes such a methodology and outlines the main phases of generic model development. The proposed methodology is illustrated with the help of examples from two advanced maturity models in the domains of Business Process Management and Knowledge Management.

Radiobiological model comparison of 3D conformal radiotherapy and IMRT plans for the treatment of prostate cancer

The main aim of radiotherapy is to deliver a dose of radiation that is high enough to destroy the tumour cells while at the same time minimising the damage to normal healthy tissues. Clinically, this has been achieved by assigning a prescription dose to the tumour volume and a set of dose constraints on critical structures. Once an optimal treatment plan has been achieved the dosimetry is assessed using the physical parameters of dose and volume. There has been an interest in using radiobiological parameters to evaluate and predict the outcome of a treatment plan in terms of both a tumour control probability (TCP) and a normal tissue complication probability (NTCP). In this study, simple radiobiological models that are available in a commercial treatment planning system were used to compare three dimensional conformal radiotherapy treatments (3D-CRT) and intensity modulated radiotherapy (IMRT) treatments of the prostate. Initially both 3D-CRT and IMRT were planned for 2 Gy/fraction to a total dose of 60 Gy to the prostate. The sensitivity of the TCP and the NTCP to both conventional dose escalation and hypo-fractionation was investigated. The biological responses were calculated using the Källman S-model. The complication free tumour control probability (P+) is generated from the combined NTCP and TCP response values. It has been suggested that the alpha/beta ratio for prostate carcinoma cells may be lower than for most other tumour cell types. The effect of this on the modelled biological response for the different fractionation schedules was also investigated.