A simulation study of unified GPS and roadside ranging technologies for vehicle positioning

The future vehicle navigation for safety applications requires seamless positioning at the accuracy of sub-meter or better. However, standalone Global Positioning System (GPS) or Differential GPS (DGPS) suffer from solution outages while being used in restricted areas such as high-rise urban areas and tunnels due to the blockages of satellite signals. Smoothed DGPS can provide sub-meter positioning accuracy, but not the seamless requirement. A disadvantage of the traditional navigation aids such as Dead Reckoning and Inertial Measurement Unit onboard vehicles are either not accurate enough due to error accumulation or too expensive to be acceptable by the mass market vehicle users. One of the alternative technologies is to use the wireless infrastructure installed in roadside to locate vehicles in regions where the Global Navigation Satellite Systems (GNSS) signals are not available (for example: inside tunnels, urban canyons and large indoor car parks). The examples of roadside infrastructure which can be potentially used for positioning purposes could include Wireless Local Area Network (WLAN)/Wireless Personal Area Network (WPAN) based positioning systems, Ultra-wide band (UWB) based positioning systems, Dedicated Short Range Communication (DSRC) devices, Locata’s positioning technology, and accurate road surface height information over selected road segments such as tunnels. This research reviews and compares the possible wireless technologies that could possibly be installed along roadside for positioning purposes. Models and algorithms of integrating different positioning technologies are also presented. Various simulation schemes are designed to examine the performance benefits of united GNSS and roadside infrastructure for vehicle positioning. The results from these experimental studies have shown a number of useful findings. It is clear that in the open road environment where sufficient satellite signals can be obtained, the roadside wireless measurements contribute very little to the improvement of positioning accuracy at the sub-meter level, especially in the dual constellation cases. In the restricted outdoor environments where only a few GPS satellites, such as those with 45 elevations, can be received, the roadside distance measurements can help improve both positioning accuracy and availability to the sub-meter level. When the vehicle is travelling in tunnels with known heights of tunnel surfaces and roadside distance measurements, the sub-meter horizontal positioning accuracy is also achievable. Overall, simulation results have demonstrated that roadside infrastructure indeed has the potential to provide sub-meter vehicle position solutions for certain road safety applications if the properly deployed roadside measurements are obtainable.

Re-conceptualising and re-positioning Australian library and information science education for the 21st century [Final Report 2011]

How can Australian library and information science (LIS) education produce, in a sustainable manner, the diverse supply of graduates with the appropriate attributes to develop and maintain high quality professional practice in the rapidly changing 21st century? This report presents the key findings of a project that has examined this question through research into future directions for LIS education in Australia. Titled Re-conceptualising and re-positioning Australian library and information science education for the twenty-first century, the purpose of the project was to establish a consolidated and holistic picture of the Australian LIS profession, and identify how its future education and training can be mediated in a cohesive and sustainable manner. The project was undertaken with a team of 12 university and vocational LIS educators from 11 institutions around Australia between November 2009 and December 2010. Collectively, these eleven institutions represented the broad spectrum and diversity of LIS education in Australia, and enabled the project to examine education for the information profession in a holistic and synergistic manner. Participating institutions in the project included Queensland University of Technology (Project Leader), Charles Sturt University, Curtin University of Technology, Edith Cowan University, Monash University, RMIT University, University of Canberra, University of South Australia, University of Tasmania, University of Technology Sydney and Victoria University. The inception and need for the project was motivated by a range of factors. From a broad perspective several of these factors relate to concerns raised at national and international levels regarding problems with education for LIS. In addition, the motivation and need for the project also related to some unique challenges that LIS education faces in the Australian tertiary education landscape. Over recent years a range of responses to explore the various issues confronting LIS education in Australia have emerged at local and national levels however this project represented the first significant investment of funding for national research in this area. In this way, the inception of the project offered a unique opportunity and powerful mechanism through which to bring together key stakeholders and inspire discourse concerning future education for the profession. Therefore as the first national project of its kind, its intent has been to provide foundation research that will inform and guide future directions for LIS education and training in Australia. The primary objective of the project was to develop a Framework for the Education of the Information Professions in Australia. The purpose of this framework was to provide evidence based strategic recommendations that would guide Australia’s future education for the information professions. Recognising the three major and equal players in the education process the project was framed around three areas of consideration: LIS students, the LIS workforce and LIS educators. Each area of consideration aligned to a research substudy in the project. The three research substudies were titled Student Considerations, Workforce Planning Considerations and Tertiary Education Considerations. The Students substudy provided a profile of LIS students and an analysis of their choices, experiences and expectations in regard to LIS education and their graduate destinations. The Workforce substudy provided an overview and analysis of the nature of the current LIS workforce, including a focus on employer expectations and employment opportunities and comment on the core and elective skill, knowledge and attitudes of current and future LIS professionals. Finally the Tertiary Education substudy provided a profile of LIS educators and an analysis of their characteristics and experiences including the key issues and challenges. In addition it also explored current national and international trends and priorities impacting on LIS education. The project utilised a Community Based Participatory Research (CBPR) approach. This approach involves all members of the community in all aspects of the project. It recognised the unique strengths and perspectives that community members bring to the process. For this project ‘community’ comprised of all individuals who have a role in, or a vested interest in, LIS education and included LIS educators, professionals, employers, students and professional associations. Individuals from these sub-groups were invited to participate in a range of aspects of the project from design through to implementation and evaluation. A range of research methodologies were used to consider the many different perspectives of LIS education, including employers and recruiters, professional associations, students, graduates and LIS teaching staff. Data collection involved a mixed method approach of questionnaires, focus groups, semi-structured interviews and environmental scans. An array of approaches was selected to ensure that broadest possible access to different facets of the information profession would be achieved. The main findings and observations from each substudy have highlighted a range of challenges for LIS education that need to be addressed. These findings and observations have grounded the development of the Framework for the Education of the Information Professions in Australia. The framework presents eleven recommendations to progress the national approach to LIS education and guide Australia’s future education for the information professions. The framework will be used by the LIS profession, most notably its educators, as strategic directions for the future of LIS education in Australia. Framework for the Education of the Information Professions in Australia: Recommendation 1: It is recommended that a broader and more inclusive vocabulary be adopted that both recognises and celebrates the expanding landscape of the field, for example ‘information profession’, ‘information sector’, ‘information discipline’ and ‘information education’. Recommendation 2: It is recommended that a self-directed body composed of information educators be established to promote, support and lead excellence in teaching and research within the information discipline. Recommendation 3: It is recommended that Australia’s information discipline continue to develop excellence in information research that will raise the discipline’s profile and contribute to its prominence within the national and international arena. Recommendation 4: It is recommended that further research examining the nature and context of Australia’s information education programs be undertaken to ensure a sustainable and relevant future for the discipline. Recommendation 5: It is recommended that further research examining the pathways and qualifications available for entry into the Australian information sector be undertaken to ensure relevance, attractiveness, accessibility and transparency. Recommendation 6: It is recommended that strategies are developed and implemented to ensure the sustainability of the workforce of information educators. Recommendation 7: It is recommended that a national approach to promoting and marketing the information profession and thereby attracting more students to the field is developed. Recommendation 8: It is recommended that Australia’s information discipline continues to support a culture of quality teaching and learning, especially given the need to accommodate a focus on the broader information landscape and more flexible delivery options. Recommendation 9: It is recommended that strategies are developed that will support and encourage collaboration between information education within the higher education and VET sectors. Recommendation 10: It is recommended that strategies and forums are developed that will support the information sector working together to conceptualise and articulate their professional identity and educational needs. Recommendation 11: It is recommended that a research agenda be established that will identify and prioritise areas in which further development or work is needed to continue advancing information education in Australia. The key findings from this project confirm that a number of pressing issues are confronting LIS education in Australia. Left unaddressed these issues will have significant implications for the future of LIS education as well as the broader LIS profession. Consequently creating a sustainable and cohesive future can only be realised through cooperation and collaboration among all stakeholders including those with the capacity to enact radical change in university and vocational institutions. Indeed the impending adoption and implementation of the project’s recommendations will fundamentally determine whether Australian LIS education is assured both for the present day and into the future.

Experimental studies of wireless communication and GNSS kinematic positioning performance in high-mobility vehicle environments

In order to support intelligent transportation system (ITS) road safety applications such as collision avoidance, lane departure warnings and lane keeping, Global Navigation Satellite Systems (GNSS) based vehicle positioning system has to provide lane-level (0.5 to 1 m) or even in-lane-level (0.1 to 0.3 m) accurate and reliable positioning information to vehicle users. However, current vehicle navigation systems equipped with a single frequency GPS receiver can only provide road-level accuracy at 5-10 meters. The positioning accuracy can be improved to sub-meter or higher with the augmented GNSS techniques such as Real Time Kinematic (RTK) and Precise Point Positioning (PPP) which have been traditionally used in land surveying and or in slowly moving environment. In these techniques, GNSS corrections data generated from a local or regional or global network of GNSS ground stations are broadcast to the users via various communication data links, mostly 3G cellular networks and communication satellites. This research aimed to investigate the precise positioning system performances when operating in the high mobility environments. This involves evaluation of the performances of both RTK and PPP techniques using: i) the state-of-art dual frequency GPS receiver; and ii) low-cost single frequency GNSS receiver. Additionally, this research evaluates the effectiveness of several operational strategies in reducing the load on data communication networks due to correction data transmission, which may be problematic for the future wide-area ITS services deployment. These strategies include the use of different data transmission protocols, different correction data format standards, and correction data transmission at the less-frequent interval. A series of field experiments were designed and conducted for each research task. Firstly, the performances of RTK and PPP techniques were evaluated in both static and kinematic (highway with speed exceed 80km) experiments. RTK solutions achieved the RMS precision of 0.09 to 0.2 meter accuracy in static and 0.2 to 0.3 meter in kinematic tests, while PPP reported 0.5 to 1.5 meters in static and 1 to 1.8 meter in kinematic tests by using the RTKlib software. These RMS precision values could be further improved if the better RTK and PPP algorithms are adopted. The tests results also showed that RTK may be more suitable in the lane-level accuracy vehicle positioning. The professional grade (dual frequency) and mass-market grade (single frequency) GNSS receivers were tested for their performance using RTK in static and kinematic modes. The analysis has shown that mass-market grade receivers provide the good solution continuity, although the overall positioning accuracy is worse than the professional grade receivers. In an attempt to reduce the load on data communication network, we firstly evaluate the use of different correction data format standards, namely RTCM version 2.x and RTCM version 3.0 format. A 24 hours transmission test was conducted to compare the network throughput. The results have shown that 66% of network throughput reduction can be achieved by using the newer RTCM version 3.0, comparing to the older RTCM version 2.x format. Secondly, experiments were conducted to examine the use of two data transmission protocols, TCP and UDP, for correction data transmission through the Telstra 3G cellular network. The performance of each transmission method was analysed in terms of packet transmission latency, packet dropout, packet throughput, packet retransmission rate etc. The overall network throughput and latency of UDP data transmission are 76.5% and 83.6% of TCP data transmission, while the overall accuracy of positioning solutions remains in the same level. Additionally, due to the nature of UDP transmission, it is also found that 0.17% of UDP packets were lost during the kinematic tests, but this loss doesn't lead to significant reduction of the quality of positioning results. The experimental results from the static and the kinematic field tests have also shown that the mobile network communication may be blocked for a couple of seconds, but the positioning solutions can be kept at the required accuracy level by setting of the Age of Differential. Finally, we investigate the effects of using less-frequent correction data (transmitted at 1, 5, 10, 15, 20, 30 and 60 seconds interval) on the precise positioning system. As the time interval increasing, the percentage of ambiguity fixed solutions gradually decreases, while the positioning error increases from 0.1 to 0.5 meter. The results showed the position accuracy could still be kept at the in-lane-level (0.1 to 0.3 m) when using up to 20 seconds interval correction data transmission.

A runtime integrity monitoring framework for real-time relative positioning systems based on GPS and DSRC

This paper provides a three-layered framework to monitor the positioning performance requirements of Real-time Relative Positioning (RRP) systems of the Cooperative Intelligent Transport Systems (C-ITS) that support Cooperative Collision Warning (CCW) applications. These applications exploit state data of surrounding vehicles obtained solely from the Global Positioning System (GPS) and Dedicated Short-Range Communications (DSRC) units without using other sensors. To this end, the paper argues the need for the GPS/DSRC-based RRP systems to have an autonomous monitoring mechanism, since the operation of CCW applications is meant to augment safety on roads. The advantages of autonomous integrity monitoring are essential and integral to any safety-of-life system. The autonomous integrity monitoring framework proposed necessitates the RRP systems to detect/predict the unavailability of their sub-systems and of the integrity monitoring module itself, and, if available, to account for effects of data link delays and breakages of DSRC links, as well as of faulty measurement sources of GPS and/or integrated augmentation positioning systems, before the information used for safety warnings/alarms becomes unavailable, unreliable, inaccurate or misleading. Hence, a monitoring framework using a tight integration and correlation approach is proposed for instantaneous reliability assessment of the RRP systems. Ultimately, using the proposed framework, the RRP systems will provide timely alerts to users when the RRP solutions cannot be trusted or used for the intended operation.

Turbulence and Mixing in the Environment: Multi-Device Study in a Sub-tropical Estuary

In an estuary, mixing and dispersion result from a combination of large-scale advection and smallscale turbulence, which are complex to estimate. The predictions of scalar transport and mixing are often inferred and rarely accurate, due to inadequate understanding of the contributions of these difference scales to estuarine recirculation. A multi-device field study was conducted in a small sub-tropical estuary under neap tide conditions with near-zero fresh water discharge for about 48 hours. During the study, acoustic Doppler velocimeters (ADV) were sampled at high frequency (50 Hz), while an acoustic Doppler current profiler (ADCP) and global positioning system (GPS) tracked drifters were used to obtain some lower frequency spatial distribution of the flow parameters within the estuary. The velocity measurements were complemented with some continuous measurement of water depth, conductivity, temperature and some other physiochemical parameters. Thorough quality control was carried out by implementation of relevant error removal filters on the individual data set to intercept spurious data. A triple decomposition (TD) technique was introduced to access the contributions of tides, resonance and ‘true’ turbulence in the flow field. The time series of mean flow measurements for both the ADCP and drifter were consistent with those of the mean ADV data when sampled within a similar spatial domain. The tidal scale fluctuation of velocity and water level were used to examine the response of the estuary to tidal inertial current. The channel exhibited a mixed type wave with a typical phase-lag between 0.035π– 0.116π. A striking feature of the ADV velocity data was the slow fluctuations, which exhibited large amplitudes of up to 50% of the tidal amplitude, particularly in slack waters. Such slow fluctuations were simultaneously observed in a number of physiochemical properties of the channel. The ensuing turbulence field showed some degree of anisotropy. For all ADV units, the horizontal turbulence ratio ranged between 0.4 and 0.9, and decreased towards the bed, while the vertical turbulence ratio was on average unity at z = 0.32 m and approximately 0.5 for the upper ADV (z = 0.55 m). The result of the statistical analysis suggested that the ebb phase turbulence field was dominated by eddies that evolved from ejection type process, while that of the flood phase contained mixed eddies with significant amount related to sweep type process. Over 65% of the skewness values fell within the range expected of a finite Gaussian distribution and the bulk of the excess kurtosis values (over 70%) fell within the range of -0.5 and +2. The TD technique described herein allowed the characterisation of a broader temporal scale of fluctuations of the high frequency data sampled within the durations of a few tidal cycles. The study provides characterisation of the ranges of fluctuation required for an accurate modelling of shallow water dispersion and mixing in a sub-tropical estuary.

Destination Positioning Slogans - Analysis of Themes used by New Zealand Regional Tourism Organisations

A significant gap in the tourism and travel literature exists in the area of tourism destination branding. Although brands have been used as sources of differentiation in consumer goods markets for over a century, academic research attention towards destination branding has only been reported since the late 1990s. Three important components of the brand construct are brand identity, brand position and brand image. While interest in applications of brand theory to practise in tourism is increasing, there is a paucity of published research in the literature to guide destination marketing organisations (DMOs). In particular there have been few reported analyses of destination brand positioning slogans. The focus of this paper is on destination brand position slogans, which represent the interface between brand identity and brand image. Part of a wider investigation of DMO slogans worldwide, and in keeping with the conference location, the paper focuses on analysis of slogans used by New Zealand RTOs. The slogans are examined in terms of the extent to which they have been limited to ephemeral indifference. In other words, have they stood the test of time and do they effectively differentiate through a meaningful proposition? Analysis of the slogans indicates very few could be characterised as memorably distinctive. This reflects the complexity involved in capturing the essence of a multi-attributed destination in a succinct and focused positioning slogan, in a way that is both meaningful to the target audience and effectively differentiates the destination from competitors offering the same benefits.

Critical success factors for positioning Australian business talent in the global knowledge economy : a current research agenda

"Globalisation‟ and the "global knowledge economy‟ have become some of the most common "buzzwords‟ in Australian business, economic, and social sectors in the past decade. Further, knowledge service exports are a growing sector for Australia that utilise complex technical and creative capacities, increasingly rely on virtual work innovations, require new socio-technical systems to establish and maintain effective client relationships in global contexts; and – along with other innovations in the electronic age – may require novel coping abilities on the part of both managers and their employees to achieve desired outcomes (Bandura, 2002). Accordingly, this paper overviews such trends. The paper also includes a research agenda which is a "work-in-progress‟ with a major global company, Shell (Australia); it highlights both the objectives and proposed methodology of the study; it also outlines anticipated key benefits arising from the research.

New particle formation and growth at a remote, sub-tropical coastal location

A month-long intensive measurement campaign was conducted in March/April 2007 at Agnes Water, a remote coastal site just south of the Great Barrier Reef on the east coast of Australia. Particle and ion size distributions were continuously measured during the campaign. Coastal nucleation events were observed in clean, marine air masses coming from the south-east on 65% of the days. The events usually began at ~10:00 local time and lasted for 1-4 hrs. They were characterised by the appearance of a nucleation mode with a peak diameter of ~10 nm. The freshly nucleated particles grew within 1-4 hrs up to sizes of 20-50 nm. The events occurred when solar intensity was high (~1000 W m-2) and RH was low (~60%). Interestingly, the events were not related to tide height. The volatile and hygroscopic properties of freshly nucleated particles (17-22.5 nm), simultaneously measured with a volatility-hygroscopicity-tandem differential mobility analyser (VH-TDMA), were used to infer chemical composition. The majority of the volume of these particles was attributed to internally mixed sulphate and organic components. After ruling out coagulation as a source of significant particle growth, we conclude that the condensation of sulphate and/or organic vapours was most likely responsible for driving particle growth during the nucleation events. We cannot make any direct conclusions regarding the chemical species that participated in the initial particle nucleation. However, we suggest that nucleation may have resulted from the photo-oxidation products of unknown sulphur or organic vapours emitted from the waters of Hervey Bay, or from the formation of DMS-derived sulphate clusters over the open ocean that were activated to observable particles by condensable vapours emitted from the nutrient rich waters around Fraser Island or Hervey Bay. Furthermore, a unique and particularly strong nucleation event was observed during northerly wind. The event began early one morning (08:00) and lasted almost the entire day resulting in the production of a large number of ~80 nm particles (average modal concentration during the event was 3200 cm-3). The Great Barrier Reef was the most likely source of precursor vapours responsible for this event.

In the mouth of the imagination : positioning children as co-researchers and co-artists to create a professional children's theatre production

In recent decades a number of Australian artists and teacher/artists have given serious attention to the creation of performance forms and performance engagement models that respect children’s intelligence, engage with themes of relevance, avoid the cliche´s of children’s theatre whilst connecting both sincerely and playfully with current understandings of the way in which young children develop and engage with the world. Historically a majority of performing arts companies touring Australian schools or companies seeking schools to view a performance in a dedicated performance venue engage with their audiences in what can be called a ‘drop-in drop-out’ model. A six-month practice-led research project (The Tashi Project) which challenged the tenets of the ‘drop-in drop-out’ model has been recently undertaken by Sandra Gattenhof and Mark Radvan in conjunction with early childhood students from three Brisbane primary school classrooms who were positioned as co-researchers and co-artists. The children, researchers and performers worked in a complimentary relationship in both the artistic process and the development of product.

Positioning the Arts in the Australian National Curriculum

In 2008 the Australian Government embarked on the development of a National Curriculum. To date, announcements about development of learning areas in Phase 1 (English, mathematics, science and history) and Phase 2 (geography and languages) have been released. But where are the arts positioned? This article traces the advocacy strategy employed by Drama Australia and the National Advocates for Arts Education (NAAE) in the fight for the arts to be included in National Curriculum Board (NCB) timeline for development, trial and implementation.