Heavy vehicle suspensions : testing and analysis

Transport regulators consider that, with respect to pavement damage, heavy vehicles (HVs) are the riskiest vehicles on the road network. That HV suspension design contributes to road and bridge damage has been recognised for some decades. This thesis deals with some aspects of HV suspension characteristics, particularly (but not exclusively) air suspensions. This is in the areas of developing low-cost in-service heavy vehicle (HV) suspension testing, the effects of larger-than-industry-standard longitudinal air lines and the characteristics of on-board mass (OBM) systems for HVs. All these areas, whilst seemingly disparate, seek to inform the management of HVs, reduce of their impact on the network asset and/or provide a measurement mechanism for worn HV suspensions. A number of project management groups at the State and National level in Australia have been, and will be, presented with the results of the project that resulted in this thesis. This should serve to inform their activities applicable to this research. A number of HVs were tested for various characteristics. These tests were used to form a number of conclusions about HV suspension behaviours. Wheel forces from road test data were analysed. A “novel roughness” measure was developed and applied to the road test data to determine dynamic load sharing, amongst other research outcomes. Further, it was proposed that this approach could inform future development of pavement models incorporating roughness and peak wheel forces. Left/right variations in wheel forces and wheel force variations for different speeds were also presented. This led on to some conclusions regarding suspension and wheel force frequencies, their transmission to the pavement and repetitive wheel loads in the spatial domain. An improved method of determining dynamic load sharing was developed and presented. It used the correlation coefficient between two elements of a HV to determine dynamic load sharing. This was validated against a mature dynamic loadsharing metric, the dynamic load sharing coefficient (de Pont, 1997). This was the first time that the technique of measuring correlation between elements on a HV has been used for a test case vs. a control case for two different sized air lines. That dynamic load sharing was improved at the air springs was shown for the test case of the large longitudinal air lines. The statistically significant improvement in dynamic load sharing at the air springs from larger longitudinal air lines varied from approximately 30 percent to 80 percent. Dynamic load sharing at the wheels was improved only for low air line flow events for the test case of larger longitudinal air lines. Statistically significant improvements to some suspension metrics across the range of test speeds and “novel roughness” values were evident from the use of larger longitudinal air lines, but these were not uniform. Of note were improvements to suspension metrics involving peak dynamic forces ranging from below the error margin to approximately 24 percent. Abstract models of HV suspensions were developed from the results of some of the tests. Those models were used to propose further development of, and future directions of research into, further gains in HV dynamic load sharing. This was from alterations to currently available damping characteristics combined with implementation of large longitudinal air lines. In-service testing of HV suspensions was found to be possible within a documented range from below the error margin to an error of approximately 16 percent. These results were in comparison with either the manufacturer’s certified data or test results replicating the Australian standard for “road-friendly” HV suspensions, Vehicle Standards Bulletin 11. OBM accuracy testing and development of tamper evidence from OBM data were detailed for over 2000 individual data points across twelve test and control OBM systems from eight suppliers installed on eleven HVs. The results indicated that 95 percent of contemporary OBM systems available in Australia are accurate to +/- 500 kg. The total variation in OBM linearity, after three outliers in the data were removed, was 0.5 percent. A tamper indicator and other OBM metrics that could be used by jurisdictions to determine tamper events were developed and documented. That OBM systems could be used as one vector for in-service testing of HV suspensions was one of a number of synergies between the seemingly disparate streams of this project.

Equity and Trusts in Principle [3rd ed.]

Equity and Trusts : in Principle, 3rd edition is updated and revised throughout. It addresses the principles of equity and trusts and provides a clear analysis of this area.

Sense of home, sense of place : a morpho-typological comparative study of Florida and Queensland

Cities in the 21st century have become layered and complex systems not only in terms of physical form, but also social and cultural structure. Consolidated tools to analyze the urban environment have today to be improved including a strong interdisciplinary perspective in order to understand and manage the unprecedented complexity our cities are facing. Redevelopments, new estates, internal and external migrations are all dynamics which are deeply modifying the built environment directly or indirectly also affecting local identity, culture and social structure. This paper investigates the relationship between urban form and social behaviors, with particular attention to the perception of the built environment and its use by long term residents, recent migrants as well as tourists. A comparative study is suggested between South East Queensland and Florida; this two regions share common features such as subtropical climate, similar lifestyle, leisure cities and canal estates. Neighborhoods on the Gold and Sunshine Coasts have been designed using the communities of Florida, such as Celebration or Seaside, as models. These regions share also significant migration processes, similar social problems and high crime rates, which directly affect the local economies. Comparing Florida and SEQ could provide an understanding of different strategies adopted and how urban development and lifestyle can be managed maintaining social equity and security. This study, investigates people’s perception of built form and how this affects the use of public space. The relationship between built environment and social behaviour has been previously investigated, for example by environmental psychology; the innovation proposed by this research is to study the perception of place in leisure cities at multiple levels. Locals, migrants and tourists have different understanding of the built form in the same location; this understanding affects the use of space and the attitude to visit or avoid some precincts. The research methodology integrates traditional morpho-typological investigations with qualitative methods; data are collected in the first phase through online surveys about perception of urban forms. Findings guide then the selection of neighbourhoods to be investigated in detail through questionnaires and Nolli maps, specifying morphological regions as well as recurrent building typologies. A final phase includes interviews with selected stakeholders. Major urban projects are discussed addressing how they are used and perceived by locals, migrants or tourists; the comparison between SEQ and Florida allows the identification of strategies to address migration issues in both regions with particular attention to urban form and placemaking dynamics.