Algorithm for queue estimation with loop detector of time occupancy in off-ramps on signalized motorways

Long traffic queues on off-ramps significantly compromise the safety and throughput of motorways. Obtaining accurate queue information is crucial for countermeasure strategies. However, it is challenging to estimate traffic queues with locally installed inductive loop detectors. This paper deals with the problem of queue estimation with the interpretation of queuing dynamics and the corresponding time-occupancy distribution over motorway off-ramps. A novel algorithm for real-time queue estimation with two detectors is presented and discussed. Results derived from microscopic traffic simulation validated the effectiveness of the algorithm and revealed some of its useful features: (a) long and intermediate traffic queues could be accurately measured, (b) relatively simple detector input (i.e., time occupancy) was required, and (c) the estimation philosophy was independent with signal timing changes and provided the potential to cooperate with advanced strategies for signal control. Some issues concerning field implementation are also discussed.

Traffic queue estimation for metered motorway on-ramps through use of loop detector time occupancies

The primary objective of this study is to develop a robust queue estimation algorithm for motorway on-ramps. Real-time queue information is a vital input for dynamic queue management on metered on-ramps. Accurate and reliable queue information enables the management of on-ramp queue in an adaptive manner to the actual traffic queue size and thus minimises the adverse impacts of queue flush while increasing the benefit of ramp metering. The proposed algorithm is developed based on the Kalman filter framework. The fundamental conservation model is used to estimate the system state (queue size) with the flow-in and flow-out measurements. This projection results are updated with the measurement equation using the time occupancies from mid-link and link-entrance loop detectors. This study also proposes a novel single point correction method. This method resets the estimated system state to eliminate the counting errors that accumulate over time. In the performance evaluation, the proposed algorithm demonstrated accurate and reliable performances and consistently outperformed the benchmarked Single Occupancy Kalman filter (SOKF) method. The improvements over SOKF are 62% and 63% in average in terms of the estimation accuracy (MAE) and reliability (RMSE), respectively. The benefit of the innovative concepts of the algorithm is well justified by the improved estimation performance in congested ramp traffic conditions where long queues may significantly compromise the benchmark algorithm’s performance.

Learning to think spatially : what do students 'see' in numeracy test items?

Learning to think spatially in mathematics involves developing proficiency with graphics. This paper reports on 2 investigations of spatial thinking and graphics. The first investigation explored the importance of graphics as 1 of 3 communication systems (i.e. text, symbols, graphics) used to provide information in numeracy test items. The results showed that graphics were embedded in at least 50 % of test items across 3 year levels. The second investigation examined 11 – 12-year-olds’ performance on 2 mathematical tasks which required substantial interpretation of graphics and spatial thinking. The outcomes revealed that many students lacked proficiency in the basic spatial skills of visual memory and spatial perception and the more advanced skills of spatial orientation and spatial visualisation. This paper concludes with a reaffirmation of the importance of spatial thinking in mathematics and proposes ways to capitalize on graphics in learning to think spatially.

Estimation of travel time on urban networks with midlink sources and sinks

This paper presents a methodology for estimation of average travel time on signalized urban networks by integrating cumulative plots and probe data. This integration aims to reduce the relative deviations in the cumulative plots due to midlink sources and sinks. During undersaturated traffic conditions, the concept of a virtual probe is introduced, and therefore, accurate travel time can be obtained when a real probe is unavailable. For oversaturated traffic conditions, only one probe per travel time estimation interval—360 s or 3% of vehicles traversing the link as a probe—has the potential to provide accurate travel time.

Queensland Arts Council road trip : an examination of in-schools touring productions (2005-2008)

This research project explores the nature of In-School Touring Productions that are presented in Queensland classrooms by Queensland Arts Council (QAC). The research emerged from my background as a drama teacher working on secondment at QAC in the Ontour inschools department. The research follows the development of a new production Power Trip: the Adventures of Watty and Volt. The research was guided by the key question: What are some of the production and pragmatic issues that relate to In-school Touring Productions and in what ways do QAC’s Ontour inschools productions offer learning experiences? This research involved the creation of three intersecting elements: (1) a 45 minute personal documentary film, 8 Times Around the Equator. The film follows my enthusiasms for this hybrid form of theatre which developed from my childhood, teaching practice and finally in my role at QAC; (2) a multimedia DVD, Queensland Arts Council 2008 inschools Season, which presents a series of short video clips promoting QAC’s Ontour inschools program; and finally (3) this exegetical paper, Queensland Arts Council Road Trip: an Examination of In-Schools Touring Productions (2005-2008). This exegesis supports the multimedia presentations and provides additional descriptions of QAC's Ontour inschools productions which are contextualised within the history of QAC and the field of Youth Theatre generally. During the project I observed 37 QAC productions and analysed them against set criteria and as a result four types of learning experiences were identified: • Category X: X-periencing the Art Form – providing students with exposure to traditional forms of main stage theatre; • Category L: Learning Through the Art Form – communicating information using an art form to educate. For example using comedy, clowning or slapstick to teach science; • Category U: Unpacking the Art Form – deconstructing art forms and providing students with increased awareness and appreciation; and • Category M: M-bodying the Art Form – workshops and artist residencies that allow students to create their own work. The creative works (documentary film and DVDs) combine to make up 65% of the project. This exegetical paper concludes the final 35% required for submission.

Sustainable urban transport : smart technology initiatives in Singapore

Achieving sustainability is one of the major goals of many urban transportation systems. Over the years, many innovative policies have been attempted to achieve an efficient, safe, and sustainable transport system. Those policies often require smart technologies to assist implementation process and enhance effectiveness. This paper discusses how sustainability can be promoted by embedding smart technologies in a modern transportation system. In particular, this paper studies the transport system of Singapore to address how this system is addressing sustainability through the use of smart technologies. Various technological initiatives in managing traffic flow, monitoring and enforcement, sharing real-time information, and managing revenues are discussed in light of their potentiality in addressing sustainability issues. The Singapore experience provides a useful reference for the cities intending to develop and promote a sustainable transport system.

Passenger transmission and productiveness of transit lines with high loads

Deterministic transit capacity analysis applies to planning, design and operational management of urban transit systems. The Transit Capacity and Quality of Service Manual (1) and Vuchic (2, 3) enable transit performance to be quantified and assessed using transit capacity and productive capacity. This paper further defines important productive performance measures of an individual transit service and transit line. Transit work (p-km) captures the transit task performed over distance. Passenger transmission (p-km/h) captures the passenger task delivered by service at speed. Transit productiveness (p-km/h) captures transit work performed over time. These measures are useful to operators in understanding their services’ or systems’ capabilities and passenger quality of service. This paper accounts for variability in utilized demand by passengers along a line and high passenger load conditions where passenger pass-up delay occurs. A hypothetical case study of an individual bus service’s operation demonstrates the usefulness of passenger transmission in comparing existing and growth scenarios. A hypothetical case study of a bus line’s operation during a peak hour window demonstrates the theory’s usefulness in examining the contribution of individual services to line productive performance. Scenarios may be assessed using this theory to benchmark or compare lines and segments, conditions, or consider improvements.

Importance of a resilient air services network to Australian remote, rural, and regional communities

Rural, regional, and remote settlements in Australia require resilient infrastructure to remain sustainable in a context characterized by frequent large-scale natural disasters, long distances between urban centers, and the pressures of economic change. A critical aspect of this infrastructure is the air services network, a system of airports, aircraft operators, and related industries that enables the high-speed movement of people, goods, and services to remote locations. A process of deregulation during the 1970s and 1980s resulted in many of these airports passing into local government and private ownership, and the rationalization of the industry saw the closure of a number of airlines and airports. This paper examines the impacts of deregulation on the resilience of air services and the contribution that they make to regional and rural communities. In particular, the robustness, redundancy, resourcefulness, and rapidity of the system are examined. The conclusion is that while the air services network has remained resilient in a situation of considerable change, the pressures of commercialization and the tendency to manage aspects of the system in isolation have contributed to a potential decrease in overall resilience.

Design of open source framework for traffic and travel simulation

For the evaluation, design, and planning of traffic facilities and measures, traffic simulation packages are the de facto tools for consultants, policy makers, and researchers. However, the available commercial simulation packages do not always offer the desired work flow and flexibility for academic research. In many cases, researchers resort to designing and building their own dedicated models, without an intrinsic incentive (or the practical means) to make the results available in the public domain. To make matters worse, a substantial part of these efforts pertains to rebuilding basic functionality and, in many respects, reinventing the wheel. This problem not only affects the research community but adversely affects the entire traffic simulation community and frustrates the development of traffic simulation in general. For this problem to be addressed, this paper describes an open source approach, OpenTraffic, which is being developed as a collaborative effort between the Queensland University of Technology, Australia; the National Institute of Informatics, Tokyo; and the Technical University of Delft, the Netherlands. The OpenTraffic simulation framework enables academies from geographic areas and disciplines within the traffic domain to work together and contribute to a specific topic of interest, ranging from travel choice behavior to car following, and from response to intelligent transportation systems to activity planning. The modular approach enables users of the software to focus on their area of interest, whereas other functional modules can be regarded as black boxes. Specific attention is paid to a standardization of data inputs and outputs for traffic simulations. Such standardization will allow the sharing of data with many existing commercial simulation packages.

Visions and values : the Children’s Book Council of Australia’s prizing of picture books in the twenty-first century

The Children’s Book Council of Australia (CBCA) administers the oldest national prize for children’s literature in Australia. Each year, the CBCA confers “Book of the Year” awards to literature for young people in five categories. In 2001, the establishment of an “Early Childhood” category opened up the venerable “Picture Book” category (first awarded in 1955) to books with an implied readership up to 18 years of age. As a result, this category has emerged in recent years as a highly visible space within which the CBCA can contest discourses of cultural marginalisation insofar as Australian (“colonial”) literature is constructed as inferior or adjunct to the major Anglophone literary traditions, and the consistent identification of children’s literature (and, indeed, of children) as lesser than its ‘adult’ counterparts. The CBCA is engaged in defining, evaluating, and legitimising a tradition of Australian children’s literature which is underpinned by a canonical impulse, and is a reflexive practice of self-definition, self-evaluation and self-legitimisation for the CBCA itself. While it is obviously problematic to identify award winners as a canon, it is equally obvious that literary prizing is a cultural practice derived from the logic of canonicity. In his discussion of the United States’s Newbery Medal, Kenneth Kidd notes that “Medal books are instant classics, the selection process an ostensible simulation of the test of time” (169) and that “the Medal is part of the canonical architecture of children's literature” (169). Thus, it is instructive to consider the visions and values of the national, of the social, and of the literary-aesthetic, in the picture books chosen by the Children’s Book Council of Australia (CBCA) as the “best” of the early twenty-first century. These books not only constitute a kind of canon for contemporary Australian children’s literature, but may well come to define what contemporary Australian children’s literature means in the wider literary field. The Book of the Year: Picture Book awards given by the CBCA since 2001 demonstrate that it is not only true of the Booker Prize that, “The choices of winning books reflect not only on the books themselves, then, but also back on the Prize, affecting its reputation and creating journalistic capital which is vital for the Prize to achieve its prominence and impact.” (81). Many of the twenty-first century CBCA award-winning picture books complicate traditional or comfortable understanding of Australianness, children’s literature, or “appropriate” modes of form and content, reminding us that “moments when texts resist or complicate recuperation into national discourses offer fruitful points for exploring the relationships between text and celebratory context” (Roberts 6). The CBCA has taken the opportunities offered by the liberation of the Picture Book category from an implied readership to challenge dominant constructions of children’s literature in Australia, and in so doing, are engaged in overt practices of canonicity with potentially long-lasting effects. Works Cited: Kidd, Kenneth. “Prizing Children’s Literature: The Case of Newbery Gold.” Children's Literature 35 (2007): 166-190. Roberts, Gillian. Prizing Literature: The Celebration and Circulation of National Culture. Toronto: U Toronto P, 2011. Squires, Claire. “Book Marketing and the Booker Prize.” Judging a Book by Its Cover: Fans, Publishers, Designers, and the Marketing of Fiction. Eds. Nicole Matthews and Nickianne Moody. Aldershot: Ashgate, 2007. 71-82.

Calibration, estimation, and sampling issues of car-following parameters

Drivers behave in different ways, and these different behaviors are a cause of traffic disturbances. A key objective for simulation tools is to correctly reproduce this variability, in particular for car-following models. From data collection to the sampling of realistic behaviors, a chain of key issues must be addressed. This paper discusses data filtering, robustness of calibration, correlation between parameters, and sampling techniques of acceleration-time continuous car-following models. The robustness of calibration is systematically investigated with an objective function that allows confidence regions around the minimum to be obtained. Then, the correlation between sets of calibrated parameters and the validity of the joint distributions sampling techniques are discussed. This paper confirms the need for adapted calibration and sampling techniques to obtain realistic sets of car-following parameters, which can be used later for simulation purposes.

Workers’ attitude towards bus rapid transit: Considering Dhaka, Bangladesh

The Government of Bangladesh is planning to develop and implement Bus Rapid Transit (BRT) in Dhaka city. This paper presents a stated choice survey conducted to understand workers’ attitudes toward BRT in Dhaka. The survey data are analysed using a multinomial logit (MNL) model to scrutinize social and economic factors’ impact on participant’s mode choices. Analysis results reveal that males, workers of higher age, education qualification, and income have a greater tendency towards choosing BRT.

Effects of transit quality of service characteristics on daily bus ridership

A case study of Brisbane, the capital city of Queensland, Australia, explored how explicit measures of transit quality of service (e.g., service frequency, service span, and travel time ratio) and implicit environmental predictors (e.g., topographic grade factor) influenced bus ridership. The primary hypothesis tested was that bus ridership was higher in suburbs with high transit quality of service than in suburbs with limited service quality. Multiple linear regression, used to identify a strong positive relationship between route intensity (bus-km/h-km2) and bus ridership, indicated that both increased service frequency and spatial route density corresponded to higher bus ridership. Additionally, the travel time ratio (i.e., the ratio of in-vehicle transit travel time to in-vehicle automobile travel time) had a significant negative association with suburban ridership: transit use declined as travel time ratio increased. In contrast, topographic grade and service span did not significantly affect suburban bus ridership. The study findings enhance the fundamental understanding of traveler behavior, which is informative to urban transportation policy, planning, and provision.

Don't sell social science short

The News of the Week article that reports on Senator Kay Bailey Hutchison (R-TX) questioning the need to fund social science research at the National Science Foundation is alarming and shortsighted ("Senate panel chair asks why NSF funds social sciences," 12 May, p. 829). Social science research is at the fundamental core of basic research and has much to contribute to the economic viability of the United States. Twenty years of direct and jointly funded social and ecosystem science research at Colorado State University's Natural Resource Ecology Laboratory has produced deep insights into environmental and societal impacts of political upheaval, land use, and climate change in parts of Africa, Asia, and the Americas. Beyond greatly advancing our understanding of the coupled human-environmental system, the partnership of social and ecosystem science has brought scientists and decision-makers together to begin to develop solutions to difficult problems.

Property damage crash equivalency factors to solve crash frequency-severity dilemma: Case study on South Korean rural roads

Safety interventions (e.g., median barriers, photo enforcement) and road features (e.g., median type and width) can influence crash severity, crash frequency, or both. Both dimensions—crash frequency and crash severity—are needed to obtain a full accounting of road safety. Extensive literature and common sense both dictate that crashes are not created equal, with fatalities costing society more than 1,000 times the cost of property damage crashes on average. Despite this glaring disparity, the profession has not unanimously embraced or successfully defended a nonarbitrary severity weighting approach for analyzing safety data and conducting safety analyses. It is argued here that the two dimensions (frequency and severity) are made available by intelligently and reliably weighting crash frequencies and converting all crashes to property-damage-only crash equivalents (PDOEs) by using comprehensive societal unit crash costs. This approach is analogous to calculating axle load equivalents in the prediction of pavement damage: for instance, a 40,000-lb truck causes 4,025 times more stress than does a 4,000-lb car and so simply counting axles is not sufficient. Calculating PDOEs using unit crash costs is the most defensible and nonarbitrary weighting scheme, allows for the simple incorporation of severity and frequency, and leads to crash models that are sensitive to factors that affect crash severity. Moreover, using PDOEs diminishes the errors introduced by underreporting of less severe crashes—an added benefit of the PDOE analysis approach. The method is illustrated with rural road segment data from South Korea (which in practice would develop PDOEs with Korean crash cost data).