Existential place-making : the dialogical realms of design for dwelling with disability

The world of disability is often neglected or taken for granted in able-bodied society. Apart from the challenge that disability is a social construct (Linton, 1998, 2006; Longmore, 2003; Thompson, 1997) there is an impact on the people with disability that they either feel left out or they don’t belong in the larger community. The able-bodied community is also left with very little knowledge or no sensitivity towards people with disability. These internal whirlpools do not contribute to any community only to create larger gaps and higher differences between the groups of people. Peace (2010) claims that disability is something imposed on to a person on top of a physical impairment. Nord (2008) advocates that while environmental barriers and social attitudes are crucial aspects of a person’s experience, they can indeed disable a person. The study reported high-lights what is home for people with disability and their family members. The way the person with disability and family members without disability share the same home and nurture personal relationships with each other demands greater attention. This research sheds light on the intricate relationships that exists between the family members including person with disability and their built environment. These existential connections provide a holistic viewpoint and the glimpse into the lived experiences of homes for people with disability and their care-givers. Concepts of universal design or barrier free design have not been successful (Connell and Sanford, 1999) in revealing in-depth the nature of place-making for people with disability and their care-givers. Such studies fail to incorporate the holistic needs of individuals with disability and their family members in terms of their bodily, visceral, emotional, social, psycho-social, intuitive, spiritual and temporal needs, to name a few (Franz, Bitner, 2010). This paper reports on some preliminary findings on phenomena of dwelling for people with different kinds of disability and their care-givers sharing the same home from an interior design perspective.

Design and experimental testing of air slab caps which convert commercial electron diodes into dual purpose, correction-free diodes for small field dosimetry

Purpose Two diodes which do not require correction factors for small field relative output measurements are designed and validated using experimental methodology. This was achieved by adding an air layer above the active volume of the diode detectors, which canceled out the increase in response of the diodes in small fields relative to standard field sizes. Methods Due to the increased density of silicon and other components within a diode, additional electrons are created. In very small fields, a very small air gap acts as an effective filter of electrons with a high angle of incidence. The aim was to design a diode that balanced these perturbations to give a response similar to a water-only geometry. Three thicknesses of air were placed at the proximal end of a PTW 60017 electron diode (PTWe) using an adjustable “air cap”. A set of output ratios (ORfclin Det ) for square field sizes of side length down to 5 mm was measured using each air thickness and compared to ORfclin Det measured using an IBA stereotactic field diode (SFD). k fclin, f msr Qclin,Qmsr was transferred from the SFD to the PTWe diode and plotted as a function of air gap thickness for each field size. This enabled the optimal air gap thickness to be obtained by observing which thickness of air was required such that k fclin, f msr Qclin,Qmsr was equal to 1.00 at all field sizes. A similar procedure was used to find the optimal air thickness required to make a modified Sun Nuclear EDGE detector (EDGEe) which s “correction-free” in small field relative dosimetry. In addition, the feasibility of experimentally transferring k fclin, f msr Qclin,Qmsr values from the SFD to unknown diodes was tested by comparing the experimentally transferred k fclin, f msr Qclin,Qmsr values for unmodified PTWe and EDGEe diodes to Monte Carlo simulated values. Results 1.0 mm of air was required to make the PTWe diode correction-free. This modified diode (PTWeair) produced output factors equivalent to those in water at all field sizes (5–50 mm). The optimal air thickness required for the EDGEe diode was found to be 0.6 mm. The modified diode (EDGEeair) produced output factors equivalent to those in water, except at field sizes of 8 and 10 mm where it measured approximately 2% greater than the relative dose to water. The experimentally calculated k fclin, f msr Qclin,Qmsr for both the PTWe and the EDGEe diodes (without air) matched Monte Carlo simulated results, thus proving that it is feasible to transfer k fclin, f msr Qclin,Qmsr from one commercially available detector to another using experimental methods and the recommended experimental setup. Conclusions It is possible to create a diode which does not require corrections for small field output factor measurements. This has been performed and verified experimentally. The ability of a detector to be “correction-free” depends strongly on its design and composition. A nonwater-equivalent detector can only be “correction-free” if competing perturbations of the beam cancel out at all field sizes. This should not be confused with true water equivalency of a detector.

The effect of graded levels of exercise on energy intake and balance in free-living men, consuming their normal diet

Objective: To assess the effect of graded increases in exercised-induced energy expenditure (EE) on appetite, energy intake (EI), total daily EE and body weight in men living in their normal environment and consuming their usual diets. Design: Within-subject, repeated measures design. Six men (mean (s.d.) age 31.0 (5.0) y; weight 75.1 (15.96) kg; height 1.79 (0.10) m; body mass index (BMI) 23.3(2.4) kg/m2), were each studied three times during a 9 day protocol, corresponding to prescriptions of no exercise, (control) (Nex; 0 MJ/day), medium exercise level (Mex; ~1.6 MJ/day) and high exercise level (Hex; ~3.2 MJ/day). On days 1-2 subjects were given a medium fat (MF) maintenance diet (1.6 ´ resting metabolic rate (RMR)). Measurements: On days 3-9 subjects self-recorded dietary intake using a food diary and self-weighed intake. EE was assessed by continual heart rate monitoring, using the modified FLEX method. Subjects' HR (heart rate) was individually calibrated against submaximal VO2 during incremental exercise tests at the beginning and end of each 9 day study period. Respiratory exchange was measured by indirect calorimetry. Subjects completed hourly hunger ratings during waking hours to record subjective sensations of hunger and appetite. Body weight was measured daily. Results: EE amounted to 11.7, 12.9 and 16.8 MJ/day (F(2,10)=48.26; P<0.001 (s.e.d=0.55)) on the Nex, Mex and Hex treatments, respectively. The corresponding values for EI were 11.6, 11.8 and 11.8 MJ/day (F(2,10)=0.10; P=0.910 (s.e.d.=0.10)), respectively. There were no treatment effects on hunger, appetite or body weight, but there was evidence of weight loss on the Hex treatment. Conclusion: Increasing EE did not lead to compensation of EI over 7 days. However, total daily EE tended to decrease over time on the two exercise treatments. Lean men appear able to tolerate a considerable negative energy balance, induced by exercise, over 7 days without invoking compensatory increases in EI.

Developing a hybrid expert system program to aid in the design of plastic injection molding process

Experts in injection molding often refer to previous solutions to find a mold design similar to the current mold and use previous successful molding process parameters with intuitive adjustment and modification as a start for the new molding application. This approach saves a substantial amount of time and cost in experimental based corrective actions which are required in order to reach optimum molding conditions. A Case-Based Reasoning (CBR) System can perform the same task by retrieving a similar case which is applied to the new case from the case library and uses the modification rules to adapt a solution to the new case. Therefore, a CBR System can simulate human e~pertise in injection molding process design. This research is aimed at developing an interactive Hybrid Expert System to reduce expert dependency needed on the production floor. The Hybrid Expert System (HES) is comprised of CBR, flow analysis, post-processor and trouble shooting systems. The HES can provide the first set of operating parameters in order to achieve moldability condition and producing moldings free of stress cracks and warpage. In this work C++ programming language is used to implement the expert system. The Case-Based Reasoning sub-system is constructed to derive the optimum magnitude of process parameters in the cavity. Toward this end the Flow Analysis sub-system is employed to calculate the pressure drop and temperature difference in the feed system to determine the required magnitude of parameters at the nozzle. The Post-Processor is implemented to convert the molding parameters to machine setting parameters. The parameters designed by HES are implemented using the injection molding machine. In the presence of any molding defect, a trouble shooting subsystem can determine which combination of process parameters must be changed iii during the process to deal with possible variations. Constraints in relation to the application of this HES are as follows. - flow length (L) constraint: 40 mm < L < I 00 mm, - flow thickness (Th) constraint: -flow type: - material types: I mm < Th < 4 mm, unidirectional flow, High Impact Polystyrene (HIPS) and Acrylic. In order to test the HES, experiments were conducted and satisfactory results were obtained.

Architecture for a free subjectivity : Deleuze and Guattari at the Horizon of the Real

Architecture for a Free Subjectivity reformulates the French philosopher Gilles Deleuze's model of subjectivity for architecture, by surveying the prolific effects of architectural encounter, and the spaces that figure in them. For Deleuze and his Lacanian collaborator Félix Guattari, subjectivity does not refer to a person, but to the potential for and event of matter becoming subject, and the myriad ways for this to take place. By extension, this book theorizes architecture as a self-actuating or creative agency for the liberation of purely "impersonal effects." Imagine a chemical reaction, a riot in the banlieues, indeed a walk through a city. Simone Brott declares that the architectural object does not merely take part in the production of subjectivity, but that it constitutes its own.

A CFD study of Hong Kong refuge floor design : floor height effect

Since 1996, ther provision of a refuge floor has been a mandatory feature for all new tall buildings in Hong Kong. These floors are designed to provide for building occupants a fire safe environment that is also free from smoke. However, the desired cross ventilation on these floors to achieve the removal of smoke, assumed by the Building Codes of Hong Kong, is still being questioned so that a further scientific study of the wind-induced ventilation of a refuge fllor is needed. This paper presents an investigation into this issue. The developed computational technique used in this paper was adopted to study the wind-induced natural ventilation on a refuge floor. The aim of the investigation was to establish whether a refuge floor with a cetnral core and having cross ventilation produced by only two open opposite external side walls on the refuge floor would provide the required protection in all situations taking into account behaviour of wind due to different floor heights, wall boundary conditions and turbulence intensity profiles. The results revealed that natural ventilation can be increased by increasng the floor heigh provided the wind angle to the building is less than 90 degrees. The effectiveness of the solution was greatly reduced when the wind was blowing at 90 degrees to the refuge floor opening.

Robust multidisciplinary design optimisation using CFD and advanced evolutionary algorithms

Computation Fluid Dynamics (CFD) has become an important tool in optimization and has seen successful in many real world applications. Most important among these is in the optimisation of aerodynamic surfaces which has become Multi-Objective (MO) and Multidisciplinary (MDO) in nature. Most of these have been carried out for a given set of input parameters such as free stream Mach number and angle of attack. One cannot ignore the fact that in aerospace engineering one frequently deals with situations where the design input parameters and flight/flow conditions have some amount of uncertainty attached to them. When the optimisation is carried out for fixed values of design variables and parameters however, one arrives at an optimised solution that results in good performance at design condition but poor drag or lift to drag ratio at slightly off-design conditions. The challenge is still to develop a robust design that accounts for uncertainty in the design in aerospace applications. In this paper this issue is taken up and an attempt is made to prevent the fluctuation of objective performance by using robust design technique or Uncertainty.

Slum free India program. Report on the findings and recommendations of QUT BEE workshop to investigate strategies to deliver better outcomes

As a result of a broad invitation extended by Professor Martin Betts, Executive Dean of the Faculty of Built Environment and Engineering, to the community of interest at QUT, a cross-disciplinary collaborative workshop was conducted to contribute ideas about responding to the Government of India’s urgent requirement to implement a program to re-house slum dwellers. This is a complex problem facing the Indian Ministry of Housing. Not only does the government aspire to eradicate existing slum conditions and to achieve tangible results within five years, but it must also ensure that slums do not form in the future. The workshop focused on technological innovation in construction to deliver transformation from the current unsanitary and overcrowded informal urban settlements to places that provide the economically weaker sections of Indian society with healthy, environmentally sustainable, economically viable mass housing that supports successful urban living. The workshop was conducted in two part process as follows: Initially, QUT academics from diverse fields shared current research and provided technical background to contextualise the challenge at a pre-workshop briefing session. This was followed by a one-day workshop during which participants worked intensively in multi-disciplinary groups through a series of exercises to develop innovative approaches to the complex problem of slum redevelopment. Dynamic, compressed work sessions, interspersed with cross-functional review and feedback by the whole group took place throughout the day. Reviews emphasised testing the concepts for their level of complexity, and likelihood of success. The two-stage workshop process achieved several objectives:  Inspired a sense of shared purpose amongst a diverse group of academics  Built participants’ knowledge of each other’s capacity  Engaged multi disciplinary team in an innovative design research process  Built participants’ confidence in the collaborative process  Demonstrated that collaborative problem solving can create solutions that represent transformative change.  Developed a framework of how workable solutions might be developed for the program through follow up workshops and charrettes of a similar nature involving stakeholders drawn from the context of the slum housing program management.

Motivations and intentions : a case study of design-led activism

With a focus on intention and motivation, this paper describes a study involving three organisational communities and their collective effort to develop and provide more inclusive housing for people with disabilities and their families. While many studies, such as that by Rocha & Miles (2009), focus on commercial organisations, and sustainability from an economic perspective, this study involves a not-for-profit organisation (the accommodation and service provider) as well as a research organisation and a design action group volunteering their services free of charge. From this pro-bono context, the paper describes a case study that explores the nature of the collective as a basis for creative practice and political activism and the theoretical implications and wider application in terms of emerging research in the area of collaborative entrepreneurship and design activism.

Design for eco-services. Part A - Environmental Services

Without the virtually free services of nature like clean air and water, humans would not last long. Natural systems can be incorporated in existing urban structures or spaces to add public amenity, mitigate the heat island effect, reduce pollution, add oxygen, and ensure water, electricity and food security in urban areas. Th ere are many eco-solutions that could radically reduce resource consumption and pollution and even provide surplus ecosystem services in the built environment at little or no operational cost, if adequately supported by design. Th is paper is the fi rst of a two part paper that explains what eco-services are, then provides examples of how design can generate natural as well as social capital. Using examples of actual and notional solutions, both papers set out to challenge designers to ‘think again’, and invent ways of creating net positive environmental gains through built environment design.

Design for eco-services. Part B - Building Services

Without the virtually free services of nature like clean air and water, humans would not last long. Natural systems can be incorporated in existing urban structures or spaces to add public amenity, mitigate the heat island eff ect, reduce pollution, add oxygen, and ensure water, electricity and food security in urban areas. Th ere are many eco-solutions that could radically reduce resource consumption and pollution and even provide surplus ecosystem services in the built environment at little or no operational cost, if adequately supported by design. Th is is the second part of a two part paper that explains what eco-services are, then provides examples of how design can generate natural as well as social capital. Using examples of actual and notional solutions, both papers set out to challenge designers to ‘think again’, and invent ways of creating net positive environmental gains through built environment design.

Scaling of free convection heat transfer in a triangular cavity for Pr>1

Unsteady natural convection inside a triangular cavity subject to a non-instantaneous heating on the inclined walls in the form of an imposed temperature which increases linearly up to a prescribed steady value over a prescribed time is reported. The development of the flow from start-up to a steady-state has been described based on scaling analyses and direct numerical simulations. The ramp temperature has been chosen in such a way that the boundary layer is reached a quasi-steady mode before the growth of the temperature is completed. In this mode the thermal boundary layer at first grows in thickness, then contracts with increasing time. However, if the imposed wall temperature growth period is sufficiently short, the boundary layer develops differently. It is seen that the shape of many houses are isosceles triangular cross-section. The heat transfer process through the roof of the attic-shaped space should be well understood. Because, in the building energy, one of the most important objectives for design and construction of houses is to provide thermal comfort for occupants. Moreover, in the present energy-conscious society it is also a requirement for houses to be energy efficient, i.e. the energy consumption for heating or air-conditioning houses must be minimized.

A free weekly iron-folic acid supplementation and regular deworming program is associated with improved hemoglobin and iron status indicators in Vietnamese women

Background Anemia due to iron deficiency is recognized as one of the major nutritional deficiencies in women and children in developing countries. Daily iron supplementation for pregnant women is recommended in many countries although there are few reports of these programs working efficiently or effectively. Weekly iron-folic acid supplementation (WIFS) and regular deworming treatment is recommended for non-pregnant women living in areas with high rates of anemia. Following a baseline survey to assess the prevalence of anemia, iron deficiency and soil transmitted helminth infections, we implemented a program to make WIFS and regular deworming treatment freely and universally available for all women of reproductive age in two districts of a province in northern Vietnam over a 12 month period. The impact of the program at the population level was assessed in terms of: i) change in mean hemoglobin and iron status indicators, and ii) change in the prevalence of anemia, iron deficiency and hookworm infections. Method Distribution of WIFS and deworming were integrated with routine health services and made available to 52,000 women. Demographic data and blood and stool samples were collected in baseline, and three and 12-month post-implementation surveys using a population-based, stratified multi-stage cluster sampling design. Results The mean Hb increased by 9.6 g/L (95% CI, 5.7, 13.5, p < 0.001) during the study period. Anemia (Hb<120 g/L) was present in 131/349 (37.5%, 95% CI 31.3, 44.8) subjects at baseline, and in 70/363 (19.3%, 95% CI 14.0, 24.6) after twelve months. Iron deficiency reduced from 75/329 (22.8%, 95% CI 16.9, 28.6) to 33/353 (9.3%, 95% CI 5.7, 13.0) by the 12-mnth survey, and hookworm infection from 279/366 (76.2%,, 95% CI 68.6, 83.8) to 66/287 (23.0%, 95% CI 17.5, 28.5) over the same period. Conclusion A free, universal WIFS program with regular deworming was associated with reduced prevalence and severity of anemia, iron deficiency and ho

How design of the physical environment impacts early learning : educators and parents perspectives

This research explores the quality and importance of the physical environment of two early learning centres on the Sunshine Coast in Queensland, utilising qualitative interviews with parents (n=4) and educators (n=4) to understand how design might impact on children’s development and a quantitative rating (the Early Childhood Physical Environment Rating Scale; ECPERS) to assess the quality of the physical built environment and infrastructure. With an average ECPERS quality rating, thematic analysis of the interviews revealed that educators and parents viewed the physical environment as important to a child’s development, although the quality of staff was predominant. Early learning centres should be ‘homely’, inviting, bright and linked to the outdoors, with participants describing how space “welcomes the child, makes them feel safe and encourages learning”. Four key themes characterised views: Emotional Connection (quality of staff and physical environment), Experiencing Design (impact of design on child development), Hub for Community Integration (relationships and resources) and Future Vision (ideal physical environment, technology and ratings). With participants often struggling to clearly articulate their thoughts on design issues, a collaborative and jargon-free approach to designing space is required. These findings will help facilitate discussion about the role and design of the physical environment in early childhood centres, with the tangible examples of ‘ideal space’ enhancing communication between architects and educators about how best to design and reconfigure space to enhance learning outcomes.