Z-source-inverter-based flexible distributed generation system solution for grid power quality improvement

Distributed generation (DG) systems are usually connected to the grid using power electronic converters. Power delivered from such DG sources depends on factors like energy availability and load demand. The converters used in power conversion do not operate with their full capacity all the time. The unused or remaining capacity of the converters could be used to provide some ancillary functions like harmonic and unbalance mitigation of the power distribution system. As some of these DG sources have wide operating ranges, they need special power converters for grid interfacing. Being a single-stage buck-boost inverter, recently proposed Z-source inverter (ZSI) is a good candidate for future DG systems. This paper presents a controller design for a ZSI-based DG system to improve power quality of distribution systems. The proposed control method is tested with simulation results obtained using Matlab/Simulink/PLECS and subsequently it is experimentally validated using a laboratory prototype.

Locating people in video from semantic descriptions : a new database and approach

The location of previously unseen and unregistered individuals in complex camera networks from semantic descriptions is a time consuming and often inaccurate process carried out by human operators, or security staff on the ground. To promote the development and evaluation of automated semantic description based localisation systems, we present a new, publicly available, unconstrained 110 sequence database, collected from 6 stationary cameras. Each sequence contains detailed semantic information for a single search subject who appears in the clip (gender, age, height, build, hair and skin colour, clothing type, texture and colour), and between 21 and 290 frames for each clip are annotated with the target subject location (over 11,000 frames are annotated in total). A novel approach for localising a person given a semantic query is also proposed and demonstrated on this database. The proposed approach incorporates clothing colour and type (for clothing worn below the waist), as well as height and build to detect people. A method to assess the quality of candidate regions, as well as a symmetry driven approach to aid in modelling clothing on the lower half of the body, is proposed within this approach. An evaluation on the proposed dataset shows that a relative improvement in localisation accuracy of up to 21 is achieved over the baseline technique.

Wet tropics reef rescue impact report 2009

The Wet Tropics region has a unique water asset and is also considered a priority region for the improvement of water quality entering the Great Barrier Reef due to a combination of high rainfall, intensive agricultural use, urban areas and the proximity of valuable reef assets to the coast. Agricultural activities are one of many identified threats to water quality and water flows in the Wet Tropics in terms of sediment and pollutant-related water quality decline. Information describing the current state of agricultural management practices across the region is patchy at best. Based on the best available information on agricultural management practices in the Wet Tropics in 2008, it is clear that opportunities exist to improve nutrient, sediment and pesticide management practice to reduce the impact on the water asset and the Great Barrier Reef. Based on current understandings of practices and the relationship between practices and reef water quality, the greatest opportunities for improved water quality are as follows: · nutrients – correct rate and the placement of fertilisers; · pesticides – improve weed control planning, herbicide rates and calibration practice; and · soil and sediment – implement new farming system practices. The 2008-09 Reef Rescue program sought to accelerate the rate of adoption of improved management practices and through Terrain invested $6.8M in the 2008-09 year for: · landholder water quality improvement incentive payments; · cross regional catchment repair of wetlands and riparian lands in areas of high sediment or nutrient loss; and · partnerships in the region to lever resources and support for on-ground practice change. The program delivered $3,021,999 in onground incentives to landholders in the Wet Tropics to improve farm practices from D or C level to B or A level. The landholder Water Quality Incentives Grants program received 300 individual applications for funding and funded 143 individual landholders to implement practice change across 36,098 ha of farm land. It is estimated that the Reef Rescue program facilitated practice change across 21% of the cane industry, and 20% of the banana industry. The program levered an additional $2,441,166 in landholder cash contributions and a further $907,653 in non-cash in-kind contributions bringing the total project value of the landholder grants program in the Wet Tropics to $6,370,819. Most funded projects targeted multiple water quality objectives with a focus on nutrient and sediment reduction. Of the 143 projects funded, 115 projects addressed nutrient management either as the primary focus or in combination with strategies that targeted other water quality objectives. Overall, 82 projects addressed two or more water quality targets. Forty-five percent of incentive funds were allocated to new farming system practices (direct drill legumes, zonal tillage equipment, permanent beds, min till planting equipment, GPS units, laser levelling), followed by 24% allocated to subsurface fertiliser applicators (subsurface application of fertiliser using a stool splitter or beside the stool, at the correct Six Easy Steps rate). As a result, Terrain estimates that the incentive grants achieved considerable reductions in nitrogen, phosphorus, sediment and pesticide loads. The program supported nutrient management training of 167 growers managing farms covering over 20% of the area harvested in 2008, and 18 industry advisors and resellers. This resulted in 115 growers (155 farms) developing nutrient management plans. The program also supported Integrated Weed Management training of 80 growers managing farms covering 8% of the area harvested in 2008, and 6 industry advisors and resellers. This report, which draws on the best available Reef Rescue Management Monitoring, Evaluation, Reporting, and Improvement (MERI) information to evaluate program performance and impact on water quality outcomes, is the first in a series of annual reports that will assess and evaluate the impact of the Reef Rescue program on agricultural practices and water quality outcomes. The assessment is predominantly focused on the cane industry because of data availability. In the next stage, efforts will expand to: · improve practice data for the banana and grazing industry; · gain a better understanding of the water quality trends and the factors influencing them in the Wet Tropics; in particular work will focus on linking the results of the Paddock to Reef monitoring program and practice change data to assess program impact; · enhance estimations of the impact of practice change on pollutant loads from agricultural land use; · gain a better understanding of the extent of ancillary practice (change not directly funded) resulting from Reef Rescue training/ education/communication programs; and · provide a better understanding of the economic cost of practice change across the Wet Tropics region. From an ecological perspective, water quality trends and the factors that may be contributing to change, require further investigation. There is a critical need to work towards an enhanced understanding of the link between catchment land management practice change and reef water quality, so that reduced nutrient, sediment, and pesticide discharge to the Great Barrier Reef can be quantified. This will also assist with future prioritisation of grants money to agricultural industries, catchments and sub catchments. From a social perspective, the program has delivered significant water quality benefits from landholder education and training. It is believed that these activities are giving landholders the information and tools to implement further lasting change in their production systems and in doing so, creating a change in attitude that is supportive and inclusive of Natural Resource Management (NRM). The program in the Wet Tropics has also considerably strengthened institutional partnerships for NRM, particularly between NRM and industry and extension organisations. As a result of the Reef Rescue program, all institutions are actively working together to collectively improve water quality. The Reef Rescue program is improving water quality entering the Great Barrier Reef Lagoon by catalysing substantial activity in the Wet Tropics region to improve land management practices and reduce the water quality impact of agricultural landscapes. The solid institutional partnerships between the regional body, industry, catchment and government organisations have been fundamental to the successful delivery of the landholder grant and catchment rehabilitation programs. Landholders have generally had a positive perception and reaction to the program, its intent, and the practical, focused nature of grant-based support. Demand in the program was extremely high in 2008-09 and is expected to increase in 2009-2010.

Improvement of a dynamic accumulator at ICICS 07 and its application in multi-user keyword-based retrieval on encrypted data

A dynamic accumulator is an algorithm, which merges a large set of elements into a constant-size value such that for an element accumulated, there is a witness confirming that the element was included into the value, with a property that accumulated elements can be dynamically added and deleted into/from the original set. Recently Wang et al. presented a dynamic accumulator for batch updates at ICICS 2007. However, their construction suffers from two serious problems. We analyze them and propose a way to repair their scheme. We use the accumulator to construct a new scheme for common secure indices with conjunctive keyword-based retrieval.

Development and pilot study of the Primary Care Practice Improvement Tool (PC-PIT) : an innovative approach

Objective To assess the usability and validity of the Primary Care Practice Improvement Tool (PC-PIT), a practice performance improvement tool based on 13 key elements identified by a systematic review. It was co-created with a range of partners and designed specifically for primary health care. Design This pilot study examined the PC-PIT using a formative assessment framework and mixed-methods research design. Setting and participants Six high-functioning general practices in Queensland, Australia, between February and July 2013. A total of 28 staff participated — 10 general practitioners, six practice or community nurses, 12 administrators (four practice managers; one business manager and eight reception or general administrative staff). Main outcome measures Readability, content validity and staff perceptions of the PC-PIT. Results The PC-PIT offers an appropriate and acceptable approach to internal quality improvement in general practice. Quantitative assessment scores and qualitative data from all staff identified two areas in which the PC-PIT required modification: a reduction in the indicative reading age, and simplification of governance-related terms and concepts. Conclusion The PC-PIT provides an innovative approach to address the complexity of organisational improvement in general practice and primary health care. This initial validation will be used to develop a suite of supporting, high-quality and free-to-access resources to enhance the use of the PC-PIT in general practice. Based on these findings, a national trial is now underway.

Development of gas sensing technology for ground and airborne applications powered by solar energy : methodology and experimental results

Monitoring gases for environmental, industrial and agricultural fields is a demanding task that requires long periods of observation, large quantity of sensors, data management, high temporal and spatial resolution, long term stability, recalibration procedures, computational resources, and energy availability. Wireless Sensor Networks (WSNs) and Unmanned Aerial Vehicles (UAVs) are currently representing the best alternative to monitor large, remote, and difficult access areas, as these technologies have the possibility of carrying specialised gas sensing systems, and offer the possibility of geo-located and time stamp samples. However, these technologies are not fully functional for scientific and commercial applications as their development and availability is limited by a number of factors: the cost of sensors required to cover large areas, their stability over long periods, their power consumption, and the weight of the system to be used on small UAVs. Energy availability is a serious challenge when WSN are deployed in remote areas with difficult access to the grid, while small UAVs are limited by the energy in their reservoir tank or batteries. Another important challenge is the management of data produced by the sensor nodes, requiring large amount of resources to be stored, analysed and displayed after long periods of operation. In response to these challenges, this research proposes the following solutions aiming to improve the availability and development of these technologies for gas sensing monitoring: first, the integration of WSNs and UAVs for environmental gas sensing in order to monitor large volumes at ground and aerial levels with a minimum of sensor nodes for an effective 3D monitoring; second, the use of solar energy as a main power source to allow continuous monitoring; and lastly, the creation of a data management platform to store, analyse and share the information with operators and external users. The principal outcomes of this research are the creation of a gas sensing system suitable for monitoring any kind of gas, which has been installed and tested on CH4 and CO2 in a sensor network (WSN) and on a UAV. The use of the same gas sensing system in a WSN and a UAV reduces significantly the complexity and cost of the application as it allows: a) the standardisation of the signal acquisition and data processing, thereby reducing the required computational resources; b) the standardisation of calibration and operational procedures, reducing systematic errors and complexity; c) the reduction of the weight and energy consumption, leading to an improved power management and weight balance in the case of UAVs; d) the simplification of the sensor node architecture, which is easily replicated in all the nodes. I evaluated two different sensor modules by laboratory, bench, and field tests: a non-dispersive infrared module (NDIR) and a metal-oxide resistive nano-sensor module (MOX nano-sensor). The tests revealed advantages and disadvantages of the two modules when used for static nodes at the ground level and mobile nodes on-board a UAV. Commercial NDIR modules for CO2 have been successfully tested and evaluated in the WSN and on board of the UAV. Their advantage is the precision and stability, but their application is limited to a few gases. The advantages of the MOX nano-sensors are the small size, low weight, low power consumption and their sensitivity to a broad range of gases. However, selectivity is still a concern that needs to be addressed with further studies. An electronic board to interface sensors in a large range of resistivity was successfully designed, created and adapted to operate on ground nodes and on-board UAV. The WSN and UAV created were powered with solar energy in order to facilitate outdoor deployment, data collection and continuous monitoring over large and remote volumes. The gas sensing, solar power, transmission and data management systems of the WSN and UAV were fully evaluated by laboratory, bench and field testing. The methodology created to design, developed, integrate and test these systems was extensively described and experimentally validated. The sampling and transmission capabilities of the WSN and UAV were successfully tested in an emulated mission involving the detection and measurement of CO2 concentrations in a field coming from a contaminant source; the data collected during the mission was transmitted in real time to a central node for data analysis and 3D mapping of the target gas. The major outcome of this research is the accomplishment of the first flight mission, never reported before in the literature, of a solar powered UAV equipped with a CO2 sensing system in conjunction with a network of ground sensor nodes for an effective 3D monitoring of the target gas. A data management platform was created using an external internet server, which manages, stores, and shares the data collected in two web pages, showing statistics and static graph images for internal and external users as requested. The system was bench tested with real data produced by the sensor nodes and the architecture of the platform was widely described and illustrated in order to provide guidance and support on how to replicate the system. In conclusion, the overall results of the project provide guidance on how to create a gas sensing system integrating WSNs and UAVs, how to power the system with solar energy and manage the data produced by the sensor nodes. This system can be used in a wide range of outdoor applications, especially in agriculture, bushfires, mining studies, zoology, and botanical studies opening the way to an ubiquitous low cost environmental monitoring, which may help to decrease our carbon footprint and to improve the health of the planet.

Improvement of the mode II interface fracture toughness of glass fiber reinforced plastics/aluminum laminates through vapor grown carbon fiber interleaves

The effects of acid treatment, vapor grown carbon fiber (VGCF) interlayer and the angle, i.e., 0° and 90°, between the rolling stripes of an aluminum (Al) plate and the fiber direction of glass fiber reinforced plastics (GFRP) on the mode II interlaminar mechanical properties of GFRP/Al laminates were investigated. The experimental results of an end notched flexure test demonstrate that the acid treatment and the proper addition of VGCF can effectively improve the critical load and mode II fracture toughness of GFRP/Al laminates. The specimens with acid treatment and 10 g m−2 VGCF addition possess the highest mode II fracture toughness, i.e., 269% and 385% increases in the 0° and 90° specimens, respectively compared to those corresponding pristine ones. Due to the induced anisotropy by the rolling stripes on the aluminum plate, the 90° specimens possess 15.3%–73.6% higher mode II fracture toughness compared to the 0° specimens. The improvement mechanisms were explored by the observation of crack propagation path and fracture surface with optical, laser scanning and scanning electron microscopies. Moreover, finite element analyses were carried out based on the cohesive zone model to verify the experimental fracture toughness and to predict the interface shear strength between the aluminum plates and GFRP laminates.

Relationship of lightning ground flashes to rainfall and wet bulb temperature

The close relationship between rain and lightning is well known. However, there are numerous documented observations of heavy rain accompanied by little or no lightning activity (Williams et al, 1992; Jayaratne, 1993). Kuleshov et al (2002) studied thunderstorm distribution and frequency in Australia and concluded that thunderstorm frequency (as expressed by number of thunder-days) in Australia does not, in general, appear to vary in any consistent way with rainfall. However, thunder-days describe occurrence of thunderstorms as heard by an observer, and therefore could be only proxy data to evaluate actual lightning activity (i.e. number of total or cloud-to-ground flashes). Field experiments have demonstrated a strong increase in lightning activity with convective available potential energy (CAPE). It has also been shown that CAPE increases linearly with potential wet bulb temperature, Tw (Williams et al, 1992). In this study, we examine the relationship between lightning ground flash incidence and the two parameters – surface rainfall and surface wet bulb maximum temperature for selected localities around Australia...

Figure and ground

Critically responding to Heimo Zobernig's painted green carpet, a semi-permanent architectural intervention realised in the immediate aftermath of my survey show, I painted the windows of the predominantly glazed space red to effectively create a two-colour painting that envelops the viewer and adds a new dimension to the painterly tradition of hinterglasmalerei. The work created an immersive environment for viewers that aimed to promote an affectual experience through the intense saturation of the complimentary contrasts red and green.

Spatially varying ground motion effects on seismic response of adjacent structures considering soil-structure interaction

Spatial variation of seismic ground motions is caused by incoherence effect, wave passage, and local site conditions. This study focuses on the effects of spatial variation of earthquake ground motion on the responses of adjacent reinforced concrete (RC) frame structures. The adjacent buildings are modeled considering soil-structure interaction (SSI) so that the buildings can be interacted with each other under uniform and non-uniform ground motions. Three different site classes are used to model the soil layers of SSI system. Based on fast Fourier transformation (FFT), spatially correlated non-uniform ground motions are generated compatible with known power spectrum density function (PSDF) at different locations. Numerical analyses are carried out to investigate the displacement responses and the absolute maximum base shear forces of adjacent structures subjected to spatially varying ground motions. The results are presented in terms of related parameters affecting the structural response using three different types of soil site classes. The responses of adjacent structures have changed remarkably due to spatial variation of ground motions. The effect can be significant on rock site rather than clay site.

Corneal confocal microscopy shown an improvement in small-fibre neuropathy in subjects with type 1 diabetes on continuous subcutaneous insulin infusion compared to multiple daily injection

Improved glycemic control is the only treatment that has been shown to be effective for diabetic peripheral neuropathy in patients with type 1 diabetes (1). Continuous subcutaneous insulin infusion (CSII) is superior to multiple daily insulin injection (MDI) for reducing HbA1c and hypoglycemic events (2). Here, we have compared the benefits of CSII compared withMDI for neuropathy over 24months....

Patients Undergoing Subacute Physical Rehabilitation following an Acute Hospital Admission Demonstrated Improvement in Cognitive Functional Task Independence

Objective. This study investigated cognitive functioning among older adults with physical debility not attributable to an acute injury or neurological condition who were receiving subacute inpatient physical rehabilitation. Design. A cohort investigation with assessments at admission and discharge. Setting. Three geriatric rehabilitation hospital wards. Participants. Consecutive rehabilitation admissions () following acute hospitalization (study criteria excluded orthopaedic, neurological, or amputation admissions). Intervention. Usual rehabilitation care. Measurements. The Functional Independence Measure (FIM) Cognitive and Motor items. Results. A total of 704 (86.5%) participants (mean age = 76.5 years) completed both assessments. Significant improvement in FIM Cognitive items (-score range 3.93–8.74, all ) and FIM Cognitive total score (-score = 9.12, ) occurred, in addition to improvement in FIM Motor performance. A moderate positive correlation existed between change in Motor and Cognitive scores (Spearman’s rho = 0.41). Generalized linear modelling indicated that better cognition at admission (coefficient = 0.398, ) and younger age (coefficient = −0.280, ) were predictive of improvement in Motor performance. Younger age (coefficient = −0.049, ) was predictive of improvement in FIM Cognitive score. Conclusions. Improvement in cognitive functioning was observed in addition to motor function improvement among this population. Causal links cannot be drawn without further research.

Effects of magnetite on high-frequency ground-penetrating radar

Large concentrations of magnetite in sedimentary deposits and soils with igneous parent material have been reported to affect geophysical sensor performance. We have undertaken the first systematic experimental effort to understand the effects of magnetite for ground-penetrating radar (GPR) characterization of the shallow subsurface. Laboratory experiments were conducted to study how homogeneous magnetite-sand mixtures and magnetite concentrated in layers affect the propagation behavior (velocity, attenuation) of high-frequency GPR waves and the reflection characteristics of a buried target. Important observations were that magnetite had a strong effect on signal velocity and reflection, at magnitudes comparable to what has been observed in small-scale laboratory experiments that measured electromagnetic properties of magnetite-silica mixtures. Magnetite also altered signal attenuation and affected the reflection characteristics of buried targets. Our results indicated important implications for several fields, including land mine detection, Martian exploration, engineering, and moisture mapping using satellite remote sensing and radiometers.