Numerical exploration of plastic deformation mechanisms of copper nanowires with surface defects

Based on the molecular dynamics simulation, plastic deformation mechanisms associated with the zigzag stress curves in perfect and surface defected copper nanowires under uniaxial tension are studied. In our previous study, it has found that the surface defect exerts larger influence than the centro-plane defect, and the 45o surface defect appears as the most influential surface defect. Hence, in this paper, the nanowire with a 45o surface defect is chosen to investigate the defect’s effect to the plastic deformation mechanism of nanowires. We find that during the plastic deformation of both perfect and defected nanowires, decrease regions of the stress curve are accompanied with stacking faults generation and migration activities, but during stress increase, the structure of the nanowire appears almost unchanged. We also observe that surface defects have obvious influence on the nanowire’s plastic deformation mechanisms. In particular, only two sets of slip planes are found to be active and twins are also observed in the defected nanowire.

A multi-resolution image alignment technique based on direct methods for pose estimation of aerial vehicles

In this paper, we seek to expand the use of direct methods in real-time applications by proposing a vision-based strategy for pose estimation of aerial vehicles. The vast majority of approaches make use of features to estimate motion. Conversely, the strategy we propose is based on a MR (Multi- Resolution) implementation of an image registration technique (Inverse Compositional Image Alignment ICIA) using direct methods. An on-board camera in a downwards-looking configuration, and the assumption of planar scenes, are the bases of the algorithm. The motion between frames (rotation and translation) is recovered by decomposing the frame-to-frame homography obtained by the ICIA algorithm applied to a patch that covers around the 80% of the image. When the visual estimation is required (e.g. GPS drop-out), this motion is integrated with the previous known estimation of the vehicles’ state, obtained from the on-board sensors (GPS/IMU), and the subsequent estimations are based only on the vision-based motion estimations. The proposed strategy is tested with real flight data in representative stages of a flight: cruise, landing, and take-off, being two of those stages considered critical: take-off and landing. The performance of the pose estimation strategy is analyzed by comparing it with the GPS/IMU estimations. Results show correlation between the visual estimation obtained with the MR-ICIA and the GPS/IMU data, that demonstrate that the visual estimation can be used to provide a good approximation of the vehicle’s state when it is required (e.g. GPS drop-outs). In terms of performance, the proposed strategy is able to maintain an estimation of the vehicle’s state for more than one minute, at real-time frame rates based, only on visual information.

Mediators of the relationship between person-organisation fit and individual outcomes

To date, research on P-O fit has focused heavily on the effect of P-O fit on individual and organisational outcomes. Few studies have attempted to explain how or why P-O fit leads to these outcomes. Meglino, Ravlin, and Adkins (1989) and Schein (1985) identified several intervening mechanisms for explaining fit-outcome relationships but only few of these explanations have been tested empirically (Cable & Edwards, 2004; Edwards & Cable, 2009; Kalliath, Bluedorn, & Strube, 1999). This thesis investigates role conflict, cognitive style and organisational justice as three potential mediating mechanisms in the relationship between P-O fit (defined as fit between personal and organisational values – value congruence or value fit) and outcomes including job satisfaction, job performance, service performance, affective commitment and continuance commitment. The study operationalised P-O fit using three measures: subjective fit, perceived fit and objective fit. The mediation model of subjective fit was tested using a Mplus analytical technique, while the mediation models of both perceived and objective fit were tested by modeling the difference between two scores (that is, between personal values and organisational values) using a polynomial regression and response surface analysis (Edwards, 1993). A survey of 558 mid-level managers from seven Brunei public sector organisations provided the data. Our results showed that the relationship between P-O fit and outcomes was partially mediated by organisational justice and cognitive style - for all the three measures of fit, while role conflict had no mediating effects. The findings from this research therefore have both theoretical and practical implications. This research contributes to the literature by combining these theoretical explanations for value congruence effects into one integrated model, and by providing evidence on the partial mediating effects of organisational justice and cognitive style. Future research needs to address and investigate other potential mechanisms by which value congruence affects individual and organisational outcomes. In addition, the study is considered to be the first to test these mediating roles for a value fit-outcomes relationship using three different measures of fit in a non-Western context.

Corporate governance mechanisms and earnings management in transitional countries – evidence from Chinese listed firms

The objective of this thesis is to investigate whether the corporate governance practices adopted by Chinese listed firms are associated with the quality of earnings information. Based on a review of agency and institutional theory, this study develops hypotheses that predict the monitoring effectiveness of the board and the audit committee. Using a combination of univariate and multivariate analyses, the association between corporate governance mechanisms and earnings management are tested from 2004 to 2008. Through analysing the empirical results, a number of findings are summarised as below. First, board independence is weakened by the introduction of government officials as independent directors on the boards. Government officials acting as independent directors, claim that they meet the definition of independent director set by the regulation. However, they have some connection with the State, which is the controlling shareholder in listed SOEs affiliated companies. Consequently, the effect of the independent director’s expertise in constraining earnings management is mitigated as demonstrated by an insignificant association between board expertise and earnings management. An alternative explanation for the inefficiency of board independence may point to the pre-selection of independent directors by the powerful CEO. It is argued that a CEO can manipulate the board composition and choose the "desirable" independent directors to monitor themselves. Second, a number of internal mechanisms, such as board size, board activities, and the separation of the roles of the CEO and chair are found to be significantly associated with discretionary accruals. This result suggests that there are advantages in having a large and active board in the Chinese setting. This can offset the disadvantages associated with large boards, such as increased bureaucracy, and hence, increase the constraining effects of a large and resourceful board. Third, factor analysis identifies two factors: CEO power and board power. CEO power is the factor which consists of CEO duality and turnover, and board power is composed of board size and board activity. The results of CEO power show that if a Chinese listed company has CEO duality and turnover at the same time, it is more likely to have a high level of earnings management. The significant and negative relationship between board power and accruals indicate that large boards with frequent meetings can be associated with low level of earnings management. Overall, the factor analysis suggests that certain governance mechanisms complement each other to become more efficient monitors of opportunistic earnings management. A combination of board characteristics can increase the negative association with earnings management. Fourth, the insignificant results between audit committees and earnings management in Chinese listed firms suggests that the Chinese regulator should strengthen the audit committee functions. This thesis calls for listed firms to disclose more information on audit committee composition and activities, which can facilitate future research on the Chinese audit committee’s monitoring role. Fifth, the interactive results between State ownership and board characteristics show that dominant State ownership has a moderating effect on board monitoring power as the State totally controls 42% of the issued shares. The high percentage of State ownership makes it difficult for the non-controlling institutional shareholders to challenge the State’s dominant status. As a result, the association between non-controlling institutional ownership and earnings management is insignificant in most situations. Lastly, firms audited by the international Big4 have lower abnormal accruals than firms audited by domestic Chinese audit firms. In addition, the inverse U-shape relationship between audit tenure and earnings quality demonstrates the changing effects of audit quality after a certain period of appointment. Furthermore, this thesis finds that listing in Hong Kong Stock Exchanges can be an alternative governance mechanism to discipline Chinese firms to follow strict Hong Kong listing requirements. Management of Hong Kong listed companies are exposed to the scrutiny of international investors and Hong Kong regulators. This in turn reduces their chances of conducting self-interested earnings manipulation. This study is designed to fill the gap in governance literature in China that is related to earnings management. Previous research on corporate governance mechanisms and earnings management in China is not conclusive. The current research builds on previous literature and provides some meaningful implications for practitioners, regulators, academic, and international investors who have investment interests in a transitional country. The findings of this study contribute to corporate governance and earnings management literature in the context of the transitional economy of China. The use of alternative measures for earnings management yields similar results compared with the accruals models and produces additional findings.

The acute adaptations of normal and pathological human Achilles tendons to eccentric and concentric exercise

Eccentric exercise is the conservative treatment of choice for mid-portion Achilles tendinopathy. While there is a growing body of evidence supporting the medium to long term efficacy of eccentric exercise in Achilles tendinopathy treatment, very few studies have investigated the short term response of the tendon to eccentric exercise. Moreover, the mechanisms through which tendinopathy symptom resolution occurs remain to be established. The primary purpose of this thesis was to investigate the acute adaptations of the Achilles tendon to, and the biomechanical characteristics of, the eccentric exercise protocol used for Achilles tendinopathy rehabilitation and a concentric equivalent. The research was conducted with an orientation towards exploring potential mechanisms through which eccentric exercise may bring about a resolution of tendinopathy symptoms. Specifically, the morphology of tendinopathic and normal Achilles tendons was monitored using high resolution sonography prior to and following eccentric and concentric exercise, to facilitate comparison between the treatment of choice and a similar alternative. To date, the only proposed mechanism through which eccentric exercise is thought to result in symptom resolution is the increased variability in motor output force observed during eccentric exercise. This thesis expanded upon prior work by investigating the variability in motor output force recorded during eccentric and concentric exercises, when performed at two different knee joint angles, by limbs with and without symptomatic tendinopathy. The methodological phase of the research focused on establishing the reliability of measures of tendon thickness, tendon echogenicity, electromyography (EMG) of the Triceps Surae and the standard deviation (SD) and power spectral density (PSD) of the vertical ground reaction force (VGRF). These analyses facilitated comparison between the error in the measurements and experimental differences identified as statistically significant, so that the importance and meaning of the experimental differences could be established. One potential limitation of monitoring the morphological response of the Achilles tendon to exercise loading is that the Achilles tendon is continually exposed to additional loading as participants complete the walking required to carry out their necessary daily tasks. The specific purpose of the last experiment in the methodological phase was to evaluate the effect of incidental walking activity on Achilles tendon morphology. The results of this study indicated that walking activity could decrease Achilles tendon thickness (negative diametral strain) and that the decrease in thickness was dependent on both the amount of walking completed and the proximity of walking activity to the sonographic examination. Thus, incidental walking activity was identified as a potentially confounding factor for future experiments which endeavoured to monitor changes in tendon thickness with exercise loading. In the experimental phase of this thesis the thickness of Achilles tendons was monitored prior to and following isolated eccentric and concentric exercise. The initial pilot study demonstrated that eccentric exercise resulted in a greater acute decrease in Achilles tendon thickness (greater diametral strain) compared to an equivalent concentric exercise, in participants with no history of Achilles tendon pain. This experiment was then expanded to incorporate participants with unilateral Achilles tendinopathy. The major finding of this experiment was that the acute decrease in Achilles tendon thickness observed following eccentric exercise was modified by the presence of tendinopathy, with a smaller decrease (less diametral strain) noted for tendinopathic compared to healthy control tendon. Based on in vitro evidence a decrease in tendon thickness is believed to reflect extrusion of fluid from the tendon with loading. This process would appear to be limited by the presence of pathology and is hypothesised to be a result of the changes in tendon structure associated with tendinopathy. Load induced fluid movement may be important to the maintenance of tendon homeostasis and structure as it has the potential to enhance molecular movement and stimulate tendon remodelling. On this basis eccentric exercise may be more beneficial to the tendon than concentric exercise. Finally, EMG and motor output force variability (SD and PSD of VGRF) were investigated while participants with and without tendinopathy performed the eccentric and concentric exercises. Although between condition differences were identified as statistically significant for a number of force variability parameters, the differences were not greater than the limits of agreement for repeated measures. Consequently the meaning and importance of these findings were questioned. Interestingly, the EMG amplitude of all three Triceps Surae muscles did not vary with knee joint angle during the performance of eccentric exercise. This raises questions pertaining to the functional importance of performing the eccentric exercise protocol at each of the two knee joint angles as it is currently prescribed. EMG amplitude was significantly greater during concentric compared to eccentric muscle actions. Differences in the muscle activation patterns may result in different stress distributions within the tendon and be related to the different diametral strain responses observed for eccentric and concentric muscle actions.

Formation mechanisms of secondary organic aerosols in relation to laser printer emissions

Due to their large surface area, complex chemical composition and high alveolar deposition rate, ultrafine particles (UFPs) (< 0.1 ìm) pose a significant risk to human health and their toxicological effects have been acknowledged by the World Health Organisation. Since people spend most of their time indoors, there is a growing concern about the UFPs present in some indoor environments. Recent studies have shown that office machines, in particular laser printers, are a significant indoor source of UFPs. The majority of printer-generated UFPs are organic carbon and it is unlikely that these particles are emitted directly from the printer or its supplies (such as paper and toner powder). Thus, it was hypothesised that these UFPs are secondary organic aerosols (SOA). Considering the widespread use of printers and human exposure to these particles, understanding the processes involved in particle formation is of critical importance. However, few studies have investigated the nature (e.g. volatility, hygroscopicity, composition, size distribution and mixing state) and formation mechanisms of these particles. In order to address this gap in scientific knowledge, a comprehensive study including state-of-art instrumental methods was conducted to characterise the real-time emissions from modern commercial laser printers, including particles, volatile organic compounds (VOCs) and ozone (O3). The morphology, elemental composition, volatility and hygroscopicity of generated particles were also examined. The large set of experimental results was analysed and interpreted to provide insight into: (1) Emissions profiles of laser printers: The results showed that UFPs dominated the number concentrations of generated particles, with a quasi unimodal size distribution observed for all tests. These particles were volatile, non-hygroscopic and mixed both externally and internally. Particle microanalysis indicated that semi-volatile organic compounds occupied the dominant fraction of these particles, with only trace quantities of particles containing Ca and Fe. Furthermore, almost all laser printers tested in this study emitted measurable concentrations of VOCs and O3. A positive correlation between submicron particles and O3 concentrations, as well as a contrasting negative correlation between submicron particles and total VOC concentrations were observed during printing for all tests. These results proved that UFPs generated from laser printers are mainly SOAs. (2) Sources and precursors of generated particles: In order to identify the possible particle sources, particle formation potentials of both the printer components (e.g. fuser roller and lubricant oil) and supplies (e.g. paper and toner powder) were investigated using furnace tests. The VOCs emitted during the experiments were sampled and identified to provide information about particle precursors. The results suggested that all of the tested materials had the potential to generate particles upon heating. Nine unsaturated VOCs were identified from the emissions produced by paper and toner, which may contribute to the formation of UFPs through oxidation reactions with ozone. (3) Factors influencing the particle emission: The factors influencing particle emissions were also investigated by comparing two popular laser printers, one showing particle emissions three orders of magnitude higher than the other. The effects of toner coverage, printing history, type of paper and toner, and working temperature of the fuser roller on particle number emissions were examined. The results showed that the temperature of the fuser roller was a key factor driving the emission of particles. Based on the results for 30 different types of laser printers, a systematic positive correlation was observed between temperature and particle number emissions for printers that used the same heating technology and had a similar structure and fuser material. It was also found that temperature fluctuations were associated with intense bursts of particles and therefore, they may have impact on the particle emissions. Furthermore, the results indicated that the type of paper and toner powder contributed to particle emissions, while no apparent relationship was observed between toner coverage and levels of submicron particles. (4) Mechanisms of SOA formation, growth and ageing: The overall hypothesis that UFPs are formed by reactions with the VOCs and O3 emitted from laser printers was examined. The results proved this hypothesis and suggested that O3 may also play a role in particle ageing. In addition, knowledge about the mixing state of generated particles was utilised to explore the detailed processes of particle formation for different printing scenarios, including warm-up, normal printing, and printing without toner. The results indicated that polymerisation may have occurred on the surface of the generated particles to produce thermoplastic polymers, which may account for the expandable characteristics of some particles. Furthermore, toner and other particle residues on the idling belt from previous print jobs were a very clear contributing factor in the formation of laser printer-emitted particles. In summary, this study not only improves scientific understanding of the nature of printer-generated particles, but also provides significant insight into the formation and ageing mechanisms of SOAs in the indoor environment. The outcomes will also be beneficial to governments, industry and individuals.

Train control to reduce delays upon service disturbances at railway junctions

Train delay is one of the most important indexes to evaluate the service quality of the railway. Because of the interactions of movement among trains, a delayed train may conflict with trains scheduled on other lines at junction area. Train that loses conflict may be forced to stop or slow down because of restrictive signals, which consequently leads to the loss of run-time and probably enlarges more delays. This paper proposes a time-saving train control method to recover delays as soon as possible. In the proposed method, golden section search is adopted to identify the optimal train speed at the expected time of restrictive signal aspect upgrades, which enables the train to depart from the conflicting area as soon as possible. A heuristic method is then developed to attain the advisory train speed profile assisting drivers in train control. Simulation study indicates that the proposed method enables the train to recover delays as soon as possible in case of disturbances at railway junctions, in comparison with the traditional maximum traction strategy and the green wave strategy.