Regulating the coal industry : striking a balance between commercial and public interests - a Queensland case study

The coal industry in Queensland operates in a very complex regulatory environment with a matrix of Federal and State laws covering the environment, health and safety, taxation and royalties, tenure, and development approvals. The Queensland Government in 2012 recognised the validity of certain industry concerns and passed two Acts being the Environmental Protection (Greentape Reduction) Amendment Act 2012 (the Greentape Act) and the Mines Legislation (Streamlining) Amendment Act 2012 (the Streamlining Act). Other changes are foreshadowed in relation to overlapping tenure and in the development of common resources legislation. Accordingly there is a great level of activity and change that has occurred or which is on the horizon. This article focuses upon these regulatory changes and foreshadows other areas requiring consideration. It commences with a consideration of the changes that have already occurred, examines those regulatory amendments that are on the drawing board and concludes with suggestions as to further interventions and amendments that have the potential to enhance the efficiency and effectiveness of the legislative framework in which coal mining is conducted.

Damage diagnosis for complex steel truss bridges using multi-layer genetic algorithm

Considerate amount of research has proposed optimization-based approaches employing various vibration parameters for structural damage diagnosis. The damage detection by these methods is in fact a result of updating the analytical structural model in line with the current physical model. The feasibility of these approaches has been proven. But most of the verification has been done on simple structures, such as beams or plates. In the application on a complex structure, like steel truss bridges, a traditional optimization process will cost massive computational resources and lengthy convergence. This study presents a multi-layer genetic algorithm (ML-GA) to overcome the problem. Unlike the tedious convergence process in a conventional damage optimization process, in each layer, the proposed algorithm divides the GA’s population into groups with a less number of damage candidates; then, the converged population in each group evolves as an initial population of the next layer, where the groups merge to larger groups. In a damage detection process featuring ML-GA, as parallel computation can be implemented, the optimization performance and computational efficiency can be enhanced. In order to assess the proposed algorithm, the modal strain energy correlation (MSEC) has been considered as the objective function. Several damage scenarios of a complex steel truss bridge’s finite element model have been employed to evaluate the effectiveness and performance of ML-GA, against a conventional GA. In both single- and multiple damage scenarios, the analytical and experimental study shows that the MSEC index has achieved excellent damage indication and efficiency using the proposed ML-GA, whereas the conventional GA only converges at a local solution.

Investigation of energy efficient approaches for the energy performance improvement of commercial buildings

Energy efficiency of buildings is attracting significant attention from the research community as the world is moving towards sustainable buildings design. Energy efficient approaches are measures or ways to improve the energy performance and energy efficiency of buildings. This study surveyed various energy-efficient approaches for commercial building and identifies Envelope Thermal Transfer Value (ETTV) and Green applications (Living wall, Green facade and Green roof) as most important and effective methods. An in-depth investigation was carried out on these energy-efficient approaches. It has been found that no ETTV model has been developed for sub-tropical climate of Australia. Moreover, existing ETTV equations developed for other countries do not take roof heat gain into consideration. Furthermore, the relationship of ETTV and different Green applications have not been investigated extensively in any literature, and the energy performance of commercial buildings in the presence of Living wall, Green facade and Green roof has not been investigated in the sub-tropical climate of Australia. The study has been conducted in two phases. First, the study develops the new formulation, coefficient and bench mark value of ETTV in the presence of external shading devices. In the new formulation, roof heat gain has been included in the integrated heat gain model made of ETTV. In the 2nd stage, the study presents the relationship of thermal and energy performance of (a) Living wall and ETTV (b) Green facade and ETTV (c) Combination of Living wall, Green facade and ETTV (d) Combination of Living wall, Green Roof and ETTV in new formulations. Finally, the study demonstrates the amount of energy that can be saved annually from different combinations of Green applications, i.e., Living wall, Green facade; combination of Living wall and Green facade; combination of Living wall and Green roof. The estimations are supported by experimental values obtained from extensive experiments of Living walls and Green roofs.

Cross-layer design and optimization for wireless networked control systems

Wireless networked control systems (WNCSs) have been widely used in the areas of manufacturing and industrial processing over the last few years. They provide real-time control with a unique characteristic: periodic traffic. These systems have a time-critical requirement. Due to current wireless mechanisms, the WNCS performance suffers from long time-varying delays, packet dropout, and inefficient channel utilization. Current wirelessly networked applications like WNCSs are designed upon the layered architecture basis. The features of this layered architecture constrain the performance of these demanding applications. Numerous efforts have attempted to use cross-layer design (CLD) approaches to improve the performance of various networked applications. However, the existing research rarely considers large-scale networks and congestion network conditions in WNCSs. In addition, there is a lack of discussions on how to apply CLD approaches in WNCSs. This thesis proposes a cross-layer design methodology to address the issues of periodic traffic timeliness, as well as to promote the efficiency of channel utilization in WNCSs. The design of the proposed CLD is highlighted by the measurement of the underlying network condition, the classification of the network state, and the adjustment of sampling period between sensors and controllers. This period adjustment is able to maintain the minimally allowable sampling period, and also maximize the control performance. Extensive simulations are conducted using the network simulator NS-2 to evaluate the performance of the proposed CLD. The comparative studies involve two aspects of communications, with and without using the proposed CLD, respectively. The results show that the proposed CLD is capable of fulfilling the timeliness requirement under congested network conditions, and is also able to improve the channel utilization efficiency and the proportion of effective data in WNCSs.

Adsorption of carbon dioxide and nitrogen on single-layer aluminum nitride nanostructures studied by density functional theory

The adsorption of carbon dioxide and nitrogen molecules on aluminum nitride (AlN) nanostructures has been explored using first-principle computational methods. Optimized configurations corresponding to physisorption and, subsequentially, chemisorption of CO2 are identified, in contrast to N2, for which only a physisorption structure is found. Transition-state searches imply a low energy barrier between the physisorption and chemisorption states for CO2 such that the latter is accessible and thermodynamically favored at room temperature. The effective binding energy of the optimized chemisorption structure is apparently larger than those for other CO2 adsorptive materials, suggesting the potential for application of aluminum nitride nanostructures for carbon dioxide capture and storage.

Australian Tax Analysis : Cases, Commentary, Commercial Applications and Questions [9th Ed.]

Now in its ninth edition, Australian Tax Analysis: Cases, Commentary, Commercial Applications and Questions has a proven track record as a high-level work for students of taxation law written by a team of authors with many years experience. Taking into account the fact that the volume of material needed to be processed by today’s taxation student can be overwhelming, the well-chosen extracts and thought-provoking commentary in Australian Tax Analysis, 9th edition, provide readers with the depth of knowledge, and reasoning and analytical skills which will be required of them as practitioners. In addition to the carefully selected case extracts and the helpful commentary, each chapter is supplemented by engaging practice questions involving problem solving, commercial decision-making, legal analysis and quantitative application. All these elements combined make Australian Tax Analysis an invaluable aid to the understanding of a subject which can be both technical and complex.

Review : "Networking : commercial television in Australia : a history" -- Nick Herd

Nick Herd begins his institutional history of Australian commercial television in the early 1890s, when an amateur inventor named Henry Sutton designed the ‘telephane’ with the intent of watching the Melbourne Cup in his home town of Ballarat. The ‘race that stops a nation’ was not broadcast live on television until 1960, but Sutton’s initiative indicates how closely sport and television were aligned in Australia even before the medium existed. The first licensed commercial stations to begin regular broadcasting went on air in Sydney and Melbourne shortly before the 1956 Melbourne Olympic Games, although Herd claims that this was ‘almost accidental’ rather than planned. (49) Only Melbourne viewers were able to see some events live, many via television sets in Ampol service stations following the company’s last minute sponsorship of coverage on Melbourne station GTV-9...

Flexural and shear bond characteristics of thin layer polymer cement mortared concrete masonry

This paper presents an experimental investigation of the flexural and shear bond characteristics of thin layer polymer cement mortared concrete masonry. It is well known that the bond characteristics of masonry depend upon the mortar type, the techniques of dispersion of mortar and the surface texture of concrete blocks; there exists an abundance of literature on the conventional 10 mm thick cement mortared masonry bond; however, 1-4 mm thick polymer cement mortared masonry bond is not yet well researched. This paper reports a study on the examination of the effect of mortar compositions, dispersion methods and unit surface textures to the flexural and shear bond characteristics of thin layer mortared concrete masonry. A non-contact digital image correlation method was adopted for the measurement of strains at the unit-mortar interface in this research. All mortar joints have been carefully prepared to ensure achievement of the desired thin layer mortar thickness on average. The results exhibit that the bond strength of thin mortar layered concrete masonry with polymer cement mortar is higher than that of the conventional masonry; moreover the unit surface texture and the mortar dispersion methods are found to have significant influence on the flexural and shear bond characteristics. From the experimental results, a correlation between the flexural and the shear bond strengths has been determined and is presented in this paper.

The need for legislative reform of the privity doctrine in commercial contracts in Malaysia : a comparative analysis

This thesis commences with the proposition that the first limb of the doctrine of privity causes injustice to third party beneficiaries in Malaysia, particularly in commercial contracts. The doctrine of privity has been the subject of criticism by the judiciary and academic commentators in common law jurisdictions, mainly directed at the first limb of the doctrine, whereby only parties to a contract can sue and be sued. The first limb prevents a third party from enforcing benefits conferred on them by those contracts thereby resulting in third parties suffering loss and injustice to those parties. In several common law countries, such as England, Australia, New Zealand and Singapore, legislative reform of the doctrine has occurred. The legislative reform has abrogated to a significant extent the doctrine of privity in commercial contracts. Malaysia is a common law country, where the doctrine of privity is still applied to contracts. An analysis of Malaysian case law demonstrates that the most affected third party beneficiaries are those seeking to enforce insurance and construction contracts. While a small number of other third parties to commercial contracts, such as agreements to pay for work done, sale and purchase agreements and tenancy agreements are also affected, the detriment is not as significant. As a consequence, this thesis focuses primarily on the impact of the doctrine of privity on commercial contracts in the areas of insurance and construction in Malaysia The thesis aims to recommend appropriate reforms to address the injustices arising from the privity doctrine for third parties seeking to obtain the benefit of insurance and construction contracts, which may also benefit third parties to other types of commercial contracts. While the Malaysian insurance, consumer protection, negotiable instruments and agency laws allow third party beneficiaries to enforce benefits in contracts, the rights are found to be inadequate. As not all third parties seeking to enforce an insurance or construction contract can rely upon the legislation, the injustice arising from the doctrine of privity remains and needs to be addressed. To achieve this aim, a comparative analysis of the rights of third party beneficiaries under insurance and construction contracts in Malaysia, Australia and England is undertaken. The results of the analysis are used to identify appropriate elements for a legislative framework guided by the three essential criteria for effective law reform developed in the thesis. The three criteria are certainty, public interest and justice. The thesis recommends first the enactment of general legislation applicable to all commercial contracts including insurance contracts. Secondly, the thesis recommends specific targeted legislation to address the injustice faced by third party beneficiaries in construction contracts.

Access to commercial destinations within the neighbourhood and walking among Australian older adults

BACKGROUND: Physical activity, particularly walking, is greatly beneficial to health; yet a sizeable proportion of older adults are insufficiently active. The importance of built environment attributes for walking is known, but few studies of older adults have examined neighbourhood destinations and none have investigated access to specific, objectively-measured commercial destinations and walking. METHODS: We undertook a secondary analysis of data from the Western Australian state government's health surveillance survey for those aged 65--84 years and living in the Perth metropolitan region from 2003--2009 (n = 2,918). Individual-level road network service areas were generated at 400 m and 800 m distances, and the presence or absence of six commercial destination types within the neighbourhood service areas identified (food retail, general retail, medical care services, financial services, general services, and social infrastructure). Adjusted logistic regression models examined access to and mix of commercial destination types within neighbourhoods for associations with self-reported walking behaviour. RESULTS: On average, the sample was aged 72.9 years (SD = 5.4), and was predominantly female (55.9%) and married (62.0%). Overall, 66.2% reported some weekly walking and 30.8% reported sufficient walking (>=150 min/week). Older adults with access to general services within 400 m (OR = 1.33, 95% CI = 1.07-1.66) and 800 m (OR = 1.20, 95% CI = 1.02-1.42), and social infrastructure within 800 m (OR = 1.19, 95% CI = 1.01-1.40) were more likely to engage in some weekly walking. Access to medical care services within 400 m (OR = 0.77, 95% CI = 0.63-0.93) and 800 m (OR = 0.83, 95% CI = 0.70-0.99) reduced the odds of sufficient walking. Access to food retail, general retail, financial services, and the mix of commercial destination types within the neighbourhood were all unrelated to walking. CONCLUSIONS: The types of neighbourhood commercial destinations that encourage older adults to walk appear to differ slightly from those reported for adult samples. Destinations that facilitate more social interaction, for example eating at a restaurant or church involvement, or provide opportunities for some incidental social contact, for example visiting the pharmacy or hairdresser, were the strongest predictors for walking among seniors in this study. This underscores the importance of planning neighbourhoods with proximate access to social infrastructure, and highlights the need to create residential environments that support activity across the life course.

Commercial successes in the music industry

Commercial success in the music industry is obviously related to one’s ability to use musical artisanship as a basis for generating profits and to accumulate substantial wealth. That may seem fairly straightforward, but commercial success is an elusive concept that is continuously negotiated within the industry to determine both what should be considered “success” as well as how it should be measured. This entry discusses commercial success in the popular music industry and strategies used to achieve it.

Cross-layer design for traffic management in wireless networked control systems

Wireless networked control systems (WNCSs) have been increasingly deployed in industrial applications. As they require timely data packet transmissions, it is difficult to make efficient use of the limited channel resources, particularly in contention based wireless networks in the layered network architecture. Aiming to maintain the WNCSs under critical real-time traffic condition at which the WNCSs marginally meet the real-time requirements, a cross-layer design (CLD) approach is presented in this paper to adaptively adjust the control period to achieve improved channel utilization while still maintaining effective and timely packet transmissions. The effectiveness of the proposed approach is demonstrated through simulation studies.

Retinal nerve fibre layer thickness is associated with higher risk of foot ulceration in diabetic peripheral neuropathy

Purpose To evaluate the association between retinal nerve fibre layer (RNFL) thickness and diabetic peripheral neuropathy in people with type 2 diabetes, and specifically those at higher risk of foot ulceration. Methods RNFL thicknesses was measured globally and in four quadrants (temporal, superior, nasal and inferior) at 3.45 mm diameter around the optic nerve head using optical coherence tomography (OCT). Severity of neuropathy was assessed using the Neuropathy Disability Score (NDS). Eighty-two participants with type 2 diabetes were stratified according to NDS scores (0-10) as: none, mild, moderate, and severe neuropathy. A control group was additionally included (n=17). Individuals with NDS≥ 6 (moderate and severe neuropathy) have been shown to be at higher risk of foot ulceration. A linear regression model was used to determine the association between RNFL and severity of neuropathy. Age, disease duration and diabetic retinopathy levels were fitted in the models. Independent t-test was employed for comparison between controls and the group without neuropathy, as well as for comparison between groups with higher and lower risk of foot ulceration. Analysis of variance was used to compare across all NDS groups. Results RNFL thickness was significantly associated with NDS in the inferior quadrant (b= -1.46, p=0.03). RNFL thicknesses globally and in superior, temporal and nasal quadrants did not show significant associations with NDS (all p>0.51). These findings were independent of the effect of age, disease duration and retinopathy. RNFL was thinner for the group with NDS ≥ 6 in all quadrants but was significant only inferiorly (p<0.005). RNFL for control participants was not significantly different from the group with diabetes and no neuropathy (superior p=0.07, global and all other quadrants: p>0.23). Mean RNFL thickness was not significantly different between the four NDS groups globally and in all quadrants (p=0.08 for inferior, P>0.14 for all other comparisons). Conclusions Retinal nerve fibre layer thinning is associated with neuropathy in people with type 2 diabetes. This relationship is strongest in the inferior retina and in individuals at higher risk of foot ulceration.

A comparison study on hydrogen sensing performance of MoO3 nanoplatelets coated with a thin layer of Ta2O5 or La2O3

There has been significant interest in developing metal oxide films with high surface area-to-volume ratio nanostructures particularly in substantially increasing the performance of Pt/oxide/semiconductor Schottky-diode gas sensors. While retaining the surface morphology of these devices, they can be further improved by modifying their nanostructured surface with a thin metal oxide layer. In this work, we analyse and compare the electrical and hydrogen-sensing properties of MoO3 nanoplatelets coated with a 4 nm layer of tantalum oxide (Ta2O5) or lanthanum oxide (La2O3). We explain in our study, that the presence of numerous defect traps at the surface (and the bulk) of the thin high-� layer causes a substantial trapping of charge during hydrogen adsorption. As a result, the interface between the Pt electrode and the thin oxide layer becomes highly polarised. Measurement results also show that the nanoplatelets coated with Ta2O5 can enable the device to be more sensitive (a larger voltage shift under hydrogen exposure) than those coated with La2O3.