Vulnerability assessment of reinforced concrete columns subjected to vehicular impacts

Columns are one of the key load bearing elements that are highly susceptible to vehicle impacts. The resulting severe damages to columns may leads to failures of the supporting structure that are catastrophic in nature. However, the columns in existing structures are seldom designed for impact due to inadequacies of design guidelines. The impact behaviour of columns designed for gravity loads and actions other than impact is, therefore, of an interest. A comprehensive investigation is conducted on reinforced concrete column with a particular focus on investigating the vulnerability of the exposed columns and to implement mitigation techniques under low to medium velocity car and truck impacts. The investigation is based on non-linear explicit computer simulations of impacted columns followed by a comprehensive validation process. The impact is simulated using force pulses generated from full scale vehicle impact tests. A material model capable of simulating triaxial loading conditions is used in the analyses. Circular columns adequate in capacity for five to twenty story buildings, designed according to Australian standards are considered in the investigation. The crucial parameters associated with the routine column designs and the different load combinations applied at the serviceability stage on the typical columns are considered in detail. Axially loaded columns are examined at the initial stage and the investigation is extended to analyse the impact behaviour under single axis bending and biaxial bending. The impact capacity reduction under varying axial loads is also investigated. Effects of the various load combinations are quantified and residual capacity of the impacted columns based on the status of the damage and mitigation techniques are also presented. In addition, the contribution of the individual parameter to the failure load is scrutinized and analytical equations are developed to identify the critical impulses in terms of the geometrical and material properties of the impacted column. In particular, an innovative technique was developed and introduced to improve the accuracy of the equations where the other techniques are failed due to the shape of the error distribution. Above all, the equations can be used to quantify the critical impulse for three consecutive points (load combinations) located on the interaction diagram for one particular column. Consequently, linear interpolation can be used to quantify the critical impulse for the loading points that are located in-between on the interaction diagram. Having provided a known force and impulse pair for an average impact duration, this method can be extended to assess the vulnerability of columns for a general vehicle population based on an analytical method that can be used to quantify the critical peak forces under different impact durations. Therefore the contribution of this research is not only limited to produce simplified yet rational design guidelines and equations, but also provides a comprehensive solution to quantify the impact capacity while delivering new insight to the scientific community for dealing with impacts.

Artful inquiry : an arts-based facilitation approach for individual and organisational learning and development

The research undertaken in these two major doctoral studies investigates the field of artsbased learning, a pedagogical approach to individual and organisational learning and development, my professional creative facilitation practice and development as a researcher. While the studies are stand-alone projects they are intended to build on each other in order to tell the evolving story of my research and professional practice. The first study combines The Role of Arts-based Learning in a Creative Economy; The Need for Artistry in Professional Education the art of knowing what to do when you don’t know what to do and Lines of Inquiry: Making Sense of Research and Professional Practice. The Role of Arts-based Learning in a Creative Economy provides an overview of the field of arts-based learning in business. The study focuses on the relevant literature and interviews with people working in the field. The paper argues that arts-based learning is a valuable addition to organisations for building a culture of creativity and innovation. The Need for Artistry in Professional Education continues that investigation. It explores the way artists approach their work and considers what skills and capabilities from artistic practice can be applied to other professions’ practices. From this research the Sphere of Professional Artistry model is developed and depicts the process of moving toward professional artistry. Lines of Inquiry: making sense of research and professional practice through artful inquiry is a self-reflective study. It explores my method of inquiry as a researcher and as a creative facilitation practitioner using arts-based learning processes to facilitate groups of people for learning, development and change. It discusses how my research and professional practice influence and inspire the other and draws on cased studies. The second major research study Artful Inquiry: Arts-based Learning for Inquiry, Reflection and Action in Professional Practice is a one year practice-led inquiry. It continues the research into arts-based and aesthetic learning experiences and my arts-based facilitation practice. The research is conducted with members of a Women’s Network in a large government service agency. It develops the concept of ‘Artful Inquiry’’ a creative, holistic, and embodied approach for facilitation, inquiry, learning, reflection, and action. Storytelling as Inquiry is used as a methodology for understanding participants’ experiences of being involved in arts-based learning experiences. The study reveals the complex and emergent nature of practice and research. It demonstrates what it can mean to do practice-led research with others, within an organisational context, and to what effect.

Alone against the crowd: Individual differences in referees' ability to cope under pressure

This paper contributes to the recent debate about the role of referees in the home advantage phenomenon. Specifically, it aims to provide a convincing answer to the newly posed question of the existence of individual differences among referees in terms of the home advantage (Boyko, Boyko, & Boyko, 2007; Johnston, 2008). Using multilevel modelling on a large and representative dataset we find that (1) the home advantage effect differs significantly among referees, and (2) this relationship is moderated by the size of the crowd. These new results suggest that a part of the home advantage is due to the effect of the crowd on the referees, and that some referees are more prone to be influenced by the crowd than others. This provides strong evidence to indicate that referees are a significant contributing factor to the home advantage. The implications of these findings are discussed both in terms of the relevant social psychological research, and with respect to the selection, assessment, and training of referees.

Interest rate caps : protection or paternalism

In a context where over-indebtedness and financial exclusion have been recognised as problems in Australia, it is undesirable that those who can least afford it, pay a high cost for short-term consumer credit. Evidence points to an increase in consumer debt in Australia and consequential over-indebtedness which has been shown to lead to a wide range of social problems.2 There is also evidence of financial exclusion, where consumers suffer a lack of access to mainstream financial services, and in Australia this is particularly the case with regard to access to safe and affordable credit.3 Financial exclusion can only exacerbate over-indebtedness, given that financially excluded, predominantly low income consumers , have been shown to turn to high cost credit to meet their short term credit needs. This is a problem that has been explored most recently in the Victorian Consumer Credit Review...

Individual agency as explanation of alliance development and change : a case study

Alliances, with other inter-organisational forms, have become a strategy of choice and necessity for both the private and public sectors. From initial formation, alliances develop and change in different ways, with research suggesting that many alliances will be terminated without their potential value being realised. Alliance process theorists address this phenomenon, seeking explanations as to why alliances unfold the way they do. However, these explanations have generally focussed on economic and structural determinants: empirically, little is known about how and why the agency of alliance actors shapes the alliance path. Theorists have suggested that current alliance process theory has provided valuable, but partial accounts of alliance development, which could be usefully extended by considering social and individual factors. The purpose of this research therefore was to extend alliance process theory by exploring individual agency as an explanation of alliance events and in doing so, reveal the potential of a multi-frame approach for understanding alliance process. Through an historical study of a single, rich case of alliance process, this thesis provided three explanations for the sequence of alliance events, each informed by a different theoretical perspective. The explanatory contribution of the Individual Agency (IA) perspective was distilled through juxtaposition with the perspectives of Environmental Determinism (ED) and Indeterminacy/Chance (I/C). The research produced a number of findings. First, it provided empirical support for the tentative proposition that the choices and practices of alliance actors are partially explanatory of alliance change and that these practices are particular to the alliance context. Secondly, the study found that examining the case through three theoretical frames provided a more complete explanation. Two propositions were put forward as to how individual agency can be theorised within this three-perspective framework. Finally, the case explained which alliance actors were required to shape alliance decision making in this case and why.

Identification of dispersion-dependent hexagonal cavity modes of an individual ZnO nanonail

The hexagonal resonator characteristics of an individual ZnO-nanonail’s head were investigated via spatially resolved cathodoluminescence (CL) at room temperature. The positions of most of distinct CL peaks in visible range were well matched to those of whispering gallery modes (WGMs) of a hexagonal dielectric cavity when we took birefringence and dispersion of refractive indices into account. The broad and weak peaks for TE polarization in long wavelength range were consistent with refractive-index values below the threshold for total internal inflection. CL peaks that were not matched to WGMs were identified as either triangular quasi-WGM or Fabry–Pérot resonance modes.

Examining the black box between stimulating regions and individual entrepreneurship

This paper seeks to investigate the link between the objective regional opportunity structure (captured by regional data) and individuals’ engagement in different stages in the venture creation process (intention to start a business and engagement in nascent entrepreneurship). We further investigate pathways through which a favourable regional environment could affect entrepreneurial intentions and the propensity to be a nascent entrepreneur. We combine individual level GEM-data for Western Germany with regional level data from the statistical office and use multi-level analysis to test our hypotheses. We find support for our contention that a favourable regional opportunity structure affects entrepreneurial intentions and engagement. As pathways between the region and individual behaviour serve the individual perception of founding opportunities and the individual social capital.

Properties of lignin and poly(hydroxybutyrate) blends

The Queensland University of Technology (QUT) allows the presentation of a thesis for the Degree of Doctor of Philosophy in the format of published or submitted papers, where such papers have been published, accepted or submitted during the period of candidature. This thesis is composed of Seven published/submitted papers and one poster presentation, of which five have been published and the other two are under review. This project is financially supported by the QUTPRA Grant. The twenty-first century started with the resurrection of lignocellulosic biomass as a potential substitute for petrochemicals. Petrochemicals, which enjoyed the sustainable economic growth during the past century, have begun to reach or have reached their peak. The world energy situation is complicated by political uncertainty and by the environmental impact associated with petrochemical import and usage. In particular, greenhouse gasses and toxic emissions produced by petrochemicals have been implicated as a significant cause of climate changes. Lignocellulosic biomass (e.g. sugarcane biomass and bagasse), which potentially enjoys a more abundant, widely distributed, and cost-effective resource base, can play an indispensible role in the paradigm transition from fossil-based to carbohydrate-based economy. Poly(3-hydroxybutyrate), PHB has attracted much commercial interest as a plastic and biodegradable material because some its physical properties are similar to those of polypropylene (PP), even though the two polymers have quite different chemical structures. PHB exhibits a high degree of crystallinity, has a high melting point of approximately 180°C, and most importantly, unlike PP, PHB is rapidly biodegradable. Two major factors which currently inhibit the widespread use of PHB are its high cost and poor mechanical properties. The production costs of PHB are significantly higher than for plastics produced from petrochemical resources (e.g. PP costs $US1 kg-1, whereas PHB costs $US8 kg-1), and its stiff and brittle nature makes processing difficult and impedes its ability to handle high impact. Lignin, together with cellulose and hemicellulose, are the three main components of every lignocellulosic biomass. It is a natural polymer occurring in the plant cell wall. Lignin, after cellulose, is the most abundant polymer in nature. It is extracted mainly as a by-product in the pulp and paper industry. Although, traditionally lignin is burnt in industry for energy, it has a lot of value-add properties. Lignin, which to date has not been exploited, is an amorphous polymer with hydrophobic behaviour. These make it a good candidate for blending with PHB and technically, blending can be a viable solution for price and reduction and enhance production properties. Theoretically, lignin and PHB affect the physiochemical properties of each other when they become miscible in a composite. A comprehensive study on structural, thermal, rheological and environmental properties of lignin/PHB blends together with neat lignin and PHB is the targeted scope of this thesis. An introduction to this research, including a description of the research problem, a literature review and an account of the research progress linking the research papers is presented in Chapter 1. In this research, lignin was obtained from bagasse through extraction with sodium hydroxide. A novel two-step pH precipitation procedure was used to recover soda lignin with the purity of 96.3 wt% from the black liquor (i.e. the spent sodium hydroxide solution). The precipitation process is presented in Chapter 2. A sequential solvent extraction process was used to fractionate the soda lignin into three fractions. These fractions, together with the soda lignin, were characterised to determine elemental composition, purity, carbohydrate content, molecular weight, and functional group content. The thermal properties of the lignins were also determined. The results are presented and discussed in Chapter 2. On the basis of the type and quantity of functional groups, attempts were made to identify potential applications for each of the individual lignins. As an addendum to the general section on the development of composite materials of lignin, which includes Chapters 1 and 2, studies on the kinetics of bagasse thermal degradation are presented in Appendix 1. The work showed that distinct stages of mass losses depend on residual sucrose. As the development of value-added products from lignin will improve the economics of cellulosic ethanol, a review on lignin applications, which included lignin/PHB composites, is presented in Appendix 2. Chapters 3, 4 and 5 are dedicated to investigations of the properties of soda lignin/PHB composites. Chapter 3 reports on the thermal stability and miscibility of the blends. Although the addition of soda lignin shifts the onset of PHB decomposition to lower temperatures, the lignin/PHB blends are thermally more stable over a wider temperature range. The results from the thermal study also indicated that blends containing up to 40 wt% soda lignin were miscible. The Tg data for these blends fitted nicely to the Gordon-Taylor and Kwei models. Fourier transform infrared spectroscopy (FT-IR) evaluation showed that the miscibility of the blends was because of specific hydrogen bonding (and similar interactions) between reactive phenolic hydroxyl groups of lignin and the carbonyl group of PHB. The thermophysical and rheological properties of soda lignin/PHB blends are presented in Chapter 4. In this chapter, the kinetics of thermal degradation of the blends is studied using thermogravimetric analysis (TGA). This preliminary investigation is limited to the processing temperature of blend manufacturing. Of significance in the study, is the drop in the apparent energy of activation, Ea from 112 kJmol-1 for pure PHB to half that value for blends. This means that the addition of lignin to PHB reduces the thermal stability of PHB, and that the comparative reduced weight loss observed in the TGA data is associated with the slower rate of lignin degradation in the composite. The Tg of PHB, as well as its melting temperature, melting enthalpy, crystallinity and melting point decrease with increase in lignin content. Results from the rheological investigation showed that at low lignin content (.30 wt%), lignin acts as a plasticiser for PHB, while at high lignin content it acts as a filler. Chapter 5 is dedicated to the environmental study of soda lignin/PHB blends. The biodegradability of lignin/PHB blends is compared to that of PHB using the standard soil burial test. To obtain acceptable biodegradation data, samples were buried for 12 months under controlled conditions. Gravimetric analysis, TGA, optical microscopy, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), FT-IR, and X-ray photoelectron spectroscopy (XPS) were used in the study. The results clearly demonstrated that lignin retards the biodegradation of PHB, and that the miscible blends were more resistant to degradation compared to the immiscible blends. To obtain an understanding between the structure of lignin and the properties of the blends, a methanol-soluble lignin, which contains 3× less phenolic hydroxyl group that its parent soda lignin used in preparing blends for the work reported in Chapters 3 and 4, was blended with PHB and the properties of the blends investigated. The results are reported in Chapter 6. At up to 40 wt% methanolsoluble lignin, the experimental data fitted the Gordon-Taylor and Kwei models, similar to the results obtained soda lignin-based blends. However, the values obtained for the interactive parameters for the methanol-soluble lignin blends were slightly lower than the blends obtained with soda lignin indicating weaker association between methanol-soluble lignin and PHB. FT-IR data confirmed that hydrogen bonding is the main interactive force between the reactive functional groups of lignin and the carbonyl group of PHB. In summary, the structural differences existing between the two lignins did not manifest itself in the properties of their blends.

Mediators of the relationship between person-organisation fit and individual outcomes

To date, research on P-O fit has focused heavily on the effect of P-O fit on individual and organisational outcomes. Few studies have attempted to explain how or why P-O fit leads to these outcomes. Meglino, Ravlin, and Adkins (1989) and Schein (1985) identified several intervening mechanisms for explaining fit-outcome relationships but only few of these explanations have been tested empirically (Cable & Edwards, 2004; Edwards & Cable, 2009; Kalliath, Bluedorn, & Strube, 1999). This thesis investigates role conflict, cognitive style and organisational justice as three potential mediating mechanisms in the relationship between P-O fit (defined as fit between personal and organisational values – value congruence or value fit) and outcomes including job satisfaction, job performance, service performance, affective commitment and continuance commitment. The study operationalised P-O fit using three measures: subjective fit, perceived fit and objective fit. The mediation model of subjective fit was tested using a Mplus analytical technique, while the mediation models of both perceived and objective fit were tested by modeling the difference between two scores (that is, between personal values and organisational values) using a polynomial regression and response surface analysis (Edwards, 1993). A survey of 558 mid-level managers from seven Brunei public sector organisations provided the data. Our results showed that the relationship between P-O fit and outcomes was partially mediated by organisational justice and cognitive style - for all the three measures of fit, while role conflict had no mediating effects. The findings from this research therefore have both theoretical and practical implications. This research contributes to the literature by combining these theoretical explanations for value congruence effects into one integrated model, and by providing evidence on the partial mediating effects of organisational justice and cognitive style. Future research needs to address and investigate other potential mechanisms by which value congruence affects individual and organisational outcomes. In addition, the study is considered to be the first to test these mediating roles for a value fit-outcomes relationship using three different measures of fit in a non-Western context.

To have your caveat and claim it, too : steps to take to protect an interest in land or water allocation

Caveats as protection for unregistered interests - lapsing and non-lapsing caveats - caveator - use only in appropriate circumstances

Enduring documents : improving the forms, improving the outcomes

Most Australian states have introduced legislation to provide for enduring documents for financial, personal and health care decision making in the event of incapacity. Since the introduction of Enduring Powers of Attorney (EPAs) and Advance Health Directives (AHDs) in Queensland in 1998, concerns have continued to be raised by service providers, professionals and individuals about the uptake, understanding and appropriate use of these documents. In response to these concerns, the Department of Justice and Attorney-General (DJAG) convened a Practical Guardianship Initiatives Working Party. This group identified the limited evidence base available to address these concerns. In 2009, a multidisciplinary research team from the University of Queensland and the Queensland University of Technology was awarded $90,000 from the Legal Practitioners Interest on Trust Account Fund to undertake a review of the current EPA and AHD forms. The goal of the research was to gather data on the content and useability of the forms from the perspectives of a range of stakeholders, particularly those completing the EPA and AHD, witnesses of these documents, attorneys appointed under an EPA, and health professionals involved in the completion of an AHD or dealing with it in a clinical context. The researchers also sought to gather information from the perspective of Aboriginal and Torres Strait Islander (ATSI) individuals as well people from culturally and linguistically diverse (CALD) groups. Although the focus of the research was on the forms and the extent to which the current design, content and format represents a barrier to uptake, in the course of the research, some broader issues were identified which have an impact on the effectiveness of the EPA and AHD in achieving the goals of planning for financial and personal and health care in advance of losing capacity. The data gathered enabled the researchers to achieve the primary goal of the research: to make recommendations to improve the content and useability of the forms which hopefully will lead to an increased uptake and appropriate use of the forms. However, the researchers thought it was important not to ignore broader policy issues that were identified in the course of the research. These broader issues have been highlighted in this Report, and the researchers have responded to them in a variety of ways. For some issues, the researchers have suggested alterations that could be made to the forms to address the particular concerns. For other issues, the researchers have suggested that Government may need to take specific action such as educating the broader community with some attention to strategies that engage particular groups within communities. Other concerns raised can only be dealt with by legislative reform and, in some of these cases, the researchers have identified issues that Government may wish to consider further. We do note, however, that it is beyond the scope of this Report to recommend changes to the law. This three stage mixed methods project aimed to provide systematic evidence from a broad range of stakeholders in regard to: (i) which groups use and do not use these documents and why, (ii) the contribution of the length/complexity/format/language of the forms as barriers to their completion and/or effective use, and (iii) the issues raised by the current documents for witnesses and attorneys. Understanding and use of EPAs and AHDs were generally explored in separate but parallel processes. A purposive sampling strategy included users of the documents as principals and attorneys, and professionals, witnesses and service providers who assist others to execute or use the forms. The first component of this study built on existing knowledge using a Critical Reference Group and material provided by the DJAG Practical Guardianship Initiatives Working Party. This assisted in the development of the data collection tools for subsequent stages. The second component comprised semi-structured interviews and focus groups with a targeted sample of current users of the forms, potential users, witnesses and other professionals to provide in-depth information on critical issues. Outreach to Aboriginal and Torres Strait Islander Elders and individuals and workers with CALD groups ensured a broad sample of potential users of the two documents. Fifty individual interviews and three focus groups were completed. Most interviews and focus groups focused on perceptions of, and experiences with, either the EPA or the AHD form. In the interviews with Indigenous people and the CALD focus groups, however, respondents provided their perceptions and experiences of both documents. In general, these respondents had not used the forms and were responding to the documents made available in the interview or focus group. In total, seventy-seven individuals were involved in interviews or focus groups. The final component comprised on-line surveys for EPA principals, EPA attorneys, AHD principals, witnesses of EPAs and AHDs and medical practitioners with experience of AHDs as nominated and/or treating doctors. The surveys were developed from the initial component and the qualitative analysis of the interview and focus group data. A total of 116 surveys were returned from major cities and regional Queensland. The survey data was analysed descriptively for patterns and trends. It is important to note that the aim of the survey was to gain insight into issues and concerns relating to the documents and not to make generalisations to the broader population.

The influence of ambient temperature on birth outcomes in Brisbane, Australia

Lately, there has been increasing interest in the association between temperature and adverse birth outcomes including preterm birth (PTB) and stillbirth. PTB is a major predictor of many diseases later in life, and stillbirth is a devastating event for parents and families. The aim of this study was to assess the seasonal pattern of adverse birth outcomes, and to examine possible associations of maternal exposure to temperature with PTB and stillbirth. We also aimed to identify if there were any periods of the pregnancy where exposure to temperature was particularly harmful. A retrospective cohort study design was used and we retrieved individual birth records from the Queensland Health Perinatal Data Collection Unit for all singleton births (excluding twins and triplets) delivered in Brisbane between 1 July 2005 and 30 June 2009. We obtained weather data (including hourly relative humidity, minimum and maximum temperature) and air-pollution data (including PM10, SO2 and O3) from the Queensland Department of Environment and Resource Management. We used survival analyses with the time-dependent variables of temperature, humidity and air pollution, and the competing risks of stillbirth and live birth. To assess the monthly pattern of the birth outcomes, we fitted month of pregnancy as a time-dependent variable. We examined the seasonal pattern of the birth outcomes and the relationship between exposure to high or low temperatures and birth outcomes over the four lag weeks before birth. We further stratified by categorisation of PTB: extreme PTB (< 28 weeks of gestation), PTB (28–36 weeks of gestation), and term birth (≥ 37 weeks of gestation). Lastly, we examined the effect of temperature variation in each week of the pregnancy on birth outcomes. There was a bimodal seasonal pattern in gestation length. After adjusting for temperature, the seasonal pattern changed from bimodal, to only one peak in winter. The risk of stillbirth was statistically significant lower in March compared with January. After adjusting for temperature, the March trough was still statistically significant and there was a peak in risk (not statistically significant) in winter. There was an acute effect of temperature on gestational age and stillbirth with a shortened gestation for increasing temperature from 15 °C to 25 °C over the last four weeks before birth. For stillbirth, we found an increasing risk with increasing temperatures from 12 °C to approximately 20 °C, and no change in risk at temperatures above 20 °C. Certain periods of the pregnancy were more vulnerable to temperature variation. The risk of PTB (28–36 weeks of gestation) increased as temperatures increased above 21 °C. For stillbirth, the fetus was most vulnerable at less than 28 weeks of gestation, but there were also effects in 28–36 weeks of gestation. For fetuses of more than 37 weeks of gestation, increasing temperatures did not increase the risk of stillbirth. We did not find any adverse affects of cold temperature on birth outcomes in this cohort. My findings contribute to knowledge of the relationship between temperature and birth outcomes. In the context of climate change, this is particularly important. The results may have implications for public health policy and planning, as they indicate that pregnant women would decrease their risk of adverse birth outcomes by avoiding exposure to high temperatures and seeking cool environments during hot days.