A preliminary study into the environmental and economic consequences of a sugar factory depithing operation

Bagasse stockpile operations have the potential to lead to adverse environmental and social impacts. Dust releases can cause occupational health and safety concerns for factory workers and dust emissions impact on the surrounding community. Preliminary modelling showed that bagasse depithing would likely reduce the environmental risks, particularly dust emissions, associated with large scale bagasse stockpiling operations. Dust emission properties were measured and used for dispersion modelling with favourable outcomes. Modelling showed a 70% reduction in peak ground level concentrations of PM10 dust (particles with an aerodynamic diameter less than 10 µm) from operations on depithed bagasse stockpiles compared to similar operations on stockpiles of whole bagasse. However, the costs of a depithing operation at a sugar factory were estimated to be approximately $2.1 million in capital expenditure to process 100,000 t/y of bagasse and operating costs were approximately $200,000 p.a. The total capital cost for a 10,000 t/y operation was approximately $1.6 million. The cost of depithing based on a discounted cash flow analysis was $5.50 per tonne of bagasse for the 100,000 t/y scenario. This may make depithing prohibitively expensive in many situations if installed exclusively as a dust control measure.

An estimate of road accident costs in Singapore

An earlier study by the Asian Development Bank (ADB) showed that the annual cost of road traffic accidents in 2001 was S$699.36 million which was 0.5% of the annual GDP. This paper attempts to update of the cost estimates of road traffic accidents. More precise methods of computing the human cost, lost output and property damage are adopted which grew in an annual cost of S$610.3 million or 0.338% of the annual GDP in 2003. A more conservative estimate of S$878,000 for fatal accident is also obtained, compared to the earlier figure of S$1.4 million. This study has shown that it is necessary to update the annual traffic accident costs regularly, as the figures vary with the number of accidents which change with time.

Role of ubiquitous sensor network in patient care

Efficient caring for the patient's information is an important aspect of caring for the patient. If these processes are possible to monitor anytime anywhere as per the patients' and doctors desecrations the cost of patient care could be minimised. In this connection, Ubiquitous Sensor Network is playing a key role on communication between physicians and patients as well as information sharing among health care providers with rapid access to medical information through reliable and trusted computer network systems. This paper argues possibilities of such scenarios by introducing a ubiquitous sensor network in patient care for 21st century's requirements and standards.

Impact of region-of-interest video coding on perceived quality in mobile video

Effective streaming of video can be achieved by providing more bits to the most important region in the frame at the cost of reduced bits in the less important regions. This strategy can be beneficial for delivering high quality videos in mobile devices, especially when the availability of bandwidth is usually low and limited. While the state-of-the-art video codecs such as H.264 may have been optimised for perceived quality, it is hypothesised that users will give more attention to interesting region/object when watching videos. Therefore, giving a higher quality to region of interest (ROI)while reducing quality of other areas may result in improving the overall perceived quality without necessarily increasing the bitrate. In this paper, the impact of ROI-based encoded video on perceived quality is investigated by conducting a user study for varous target bitrates. The results from the user study demonstrate that ROI-based video coding has superior perceived quality compared to normal encoded video at the same bitrate in the lower bitrate range.

Loss to assets : production of power from speed breaker

In this work, prospect and feasibility of power generation by using speed breakers has been investigated. In this project a mechanism to generate power by converting the potential energy generated by a vehicle going up on a speed breaker into kinetic energy. This arrangement is made one rotation as soon as the vehicle moves over the speed breaker and has been increased using gears. After the production electricity, a storing unit has been used to hoard the generated electricity during the day and will be used during the night. Two prototypes have made using rack and pinion gear, spur gear, springs and generator .From which a considerable amount of energy is obtained. Nonetheless the cost of the prototype was inexpensive which proves the feasibility of this project and the idea can be applied on heavy traffic roads. Further investigation is being carried on to introduce the technology for practical approach.

Management characteristics and the decision to internationalize : exploration of exporters vs. non-exporters within the Chilean wine industry

The objective of this study was to identify key factors differentiating between exporters and non-exporters in the Chilean wine industry. Based on survey data collected from 61 wineries, the findings show that the main barriers for non-exporters are the lack of financial resources, limited quantities of stock for market expansion, management’s lack of knowledge and experience, and the high cost of travelling and participating in trade shows. The results also show that managers have educational levels and international experience exceeding those of other comparable New World wineries. Finally, in developing their main international markets, Chilean wineries did not target psychically close markets as identified in previous wine industry studies

Intermittent drying of food products : a critical review

Drying is very energy intensive process and consumes about 20-25% of the energy used by food processing industry. The energy efficiency of the process and quality of dried product are two key factors in food drying. Global energy crisis and demand for quality dried food further challenge researchers to explore innovative techniques in food drying to address these issues. Intermittent drying is considered one of the promising solutions for improving energy efficiency and product quality without increasing the capital cost of the drier. Intermittent drying has already received much attention. However, a comprehensive review of recent progresses and overall assessment of energy efficiency and product quality in intermittent drying is lacking. The objective of this article is to discuss, analyze and evaluate the recent advances in intermittent drying research with energy efficiency and product quality as standpoint. Current available modelling techniques for intermittent drying are reviewed and their merits and demerits are analyzed. Moreover, intermittent application of ultrasound, infrared (IR) and microwave in combined drying technology have been reviewed and discussed. In this review article the gaps in the current literature are highlighted, some important future scopes for theoretical and experimental studies are identified and the direction of further research is suggested.

Reducing actuator switchings for motion control of autonomous underwater vehicles

A priority when designing control strategies for autonomous underwater vehicles is to emphasize their cost of implementation on a real vehicle and at the same time to minimize a prescribed criterion such as time, energy, payload or combination of those. Indeed, the major issue is that due to the vehicles' design and the actuation modes usually under consideration for underwater platforms the number of actuator switchings must be kept to a small value to ensure feasibility and precision. This constraint is typically not verified by optimal trajectories which might not even be piecewise constants. Our goal is to provide a feasible trajectory that minimizes the number of switchings while maintaining some qualities of the desired trajectory, such as optimality with respect to a given criterion. The one-sided Lipschitz constant is used to derive theoretical estimates. The theory is illustrated on two examples, one is a fully actuated underwater vehicle capable of motion in six degrees-of-freedom and one is minimally actuated with control motions constrained to the vertical plane.

The committee on public information : a transmedia war propaganda campaign

This thesis develops an understanding of how propaganda entered the realm of journalism and popular culture in the United States during World War I through an examination of materials created by the Committee on Public Information (CPI). The CPI was a US governmental propaganda organisation created during World War I to persuade the nation to mobilise for war. Three of its divisions were chosen for this study: the Division of News (DoN), the Division of Four Minute Men (FMM) and the Division of Pictorial Publicity (DPP). Chapter 1 provides a general context for the thesis, outlines the research questions and details previous research on the CPI. Chapter 2 outlines the methods of analysis for interpreting the case study chapters and provides contextual information. The case studies are presented in Chapters 3, 4 and 5. These chapters are structured in the order of context, medium and content, and contain historical contextual information about each particular division, medialogical aspects of its propagated form and thematic groupings created from close reading of CPI materials. A semiotic analysis in the Peircian tradition is also performed on visual forms of propaganda in Chapter 5. Chapter 6 discusses how the expectations of persuasion, truth and amusement relate to each other when mediated in culture, using Lotman’s concept of the semiosphere. This further develops an understanding of propaganda as a cultural system in relation to other cultural systems – in this case, journalism and popular culture. Chapter 7 provides conclusions about the study, outlines relative strengths and weaknesses regarding the selection and deployment of methods, makes recommendations for future research, and summarises the key contributions of the thesis.

Challenges for researchers investigating contraceptive use and pregnancy intentions of young women living in urban and rural Australia : face-to-face discussions to increase participation in a web-based survey

Background: It is imperative to understand how to engage young women in research about issues that are important to them. There is limited reliable data on how young women access contraception in Australia especially in rural areas where services may be less available. Objective: This paper identifies the challenges involved in engaging young Australian women aged 18-23 years to participate in a web-based survey on contraception and pregnancy and ensure their ongoing commitment to follow-up web-based surveys. Methods: A group of young women, aged 18-23 years and living in urban and rural New South Wales, Australia, were recruited to participate in face-to-face discussions using several methods of recruitment: direct contact (face-to-face, telephone or email)and snowball sampling by potential participants inviting their friends. All discussions were transcribed verbatim and analyzed using thematic analysis. Results: Twenty young women participated (urban, n=10: mean age 21.6 years; rural, n=10: 20.0 years) and all used computers or smart phones to access the internet on a daily basis. All participants were concerned about the cost of internet access and utilized free access to social media on their mobile phones. Their willingness to participate in a web-based survey was dependent on incentives with a preference for small financial rewards. Most participants were concerned about their personal details and survey responses remaining confidential and secure. The most appropriate survey would take up to 15 minutes to complete, be a mix of short and long questions and eye-catching with bright colours. Questions on the sensitive topics of sexual activity, contraception and pregnancy were acceptable if they could respond with “I prefer not to answer”. Conclusions: There are demographic, participation and survey design challenges in engaging young women in a web-based survey. Based on our findings, future research efforts are needed to understand the full extent of the role social media and incentives play in the decision of young women to participate in web-based research.

Airport ground transportation policies and the future of rail connections at US airports

Airports are currently being pressured to operate in a more environmentally-sensitive manner; as a response, airports have integrated environmental policies into their operations. However, environmental concerns regarding automobile traffic and related emissions have yet to be addressed. While the automobile is the dominant air passenger ground transportation mode at US airports, services facilitating automobile usage including public parking and car rentals are a major airport revenue source. Less than 20 US hub airports have direct access to rail-based transportation modes. New rail transportation projects serving additional airports are either being consideration or under construction. Regardless of whether an airport has direct access to rail-based transportation modes, the air passenger ground transportation modal split at US airports remain low in comparison to those in Asia and Europe. The high cost of providing additional US airports with direct rail connections in an era of severe governmental budgetary cutbacks is making the “build it and they will come” mindset untenable. Governmental policies are but one factor determining whether programs increasing transit usage results in automobile traffic reductions and related emissions. This study reveals that a significant percentage of the busiest US airports do not have policies fostering increases in the air passenger ground transportation modal split. A case study of one US airport is presented that has successfully adopted a transit first policy to achieve a high air passenger ground transportation modal split and facilitate the availability of rail-based transportation services.

The value of community wellbeing for locality based practice

This presentation put forward six propositions regarding the value and character of community wellbeing, in particular the economic contribution of social and community programs and initiatives. The six propositions are: 1. Community wellbeing is a useful umbrella concept 2. Everyone benefits from public programs 3. There is an economic as well as social cost of not responding well 4. Local government is key in fostering community wellbeing 5. Good practice involves bringing together a number of perspectives and levers, including social and cultural initiatives 6. Engaging with the community around wellbeing offers an opportunity to enhance the political process

What are the implications of peri-urban agriculture on food security in Australian cities?

Background: Periurban agriculture refers to agricultural practice occurring in areas with mixed rural and urban features. It is responsible 25% of the total gross value of economic production in Australia, despite only comprising 3% of the land used for agriculture. As populations grows and cities expand, they are constantly absorbing surrounding fringe areas, thus creating a new fringe, further from the city causing the periurban region to constantly shift outwards. Periurban regions are fundamental in the provision of fresh food to city populations and residential (and industrial) expansion taking over agricultural land has been noted as a major worldwide concern. Another major concern around the increase in urbanisation and resultant decrease in periurban agriculture is its potential effect on food security. Food security is the availability or access to nutritionally-adequate, culturally-relevant and safe foods in culturally-appropriate ways. Thus food insecurity occurs when access to or availability of these foods is compromised. There is an important level of connectedness between food security and food production and a decrease in periurban agriculture may have adverse effects on food security. A decrease in local, seasonal produce may result in a decrease in the availability of products and an increase in cost, as food must travel greater distances, incurring extra costs present at the consumer level. Currently, few Australian studies exist examining the change in periurban agriculture over time. Such information may prove useful for future health policy and interventions as well as infrastructure planning. The aim of this study is to investigate changes in periurban agriculture among capital cities of Australia. Methods: We compared data pertaining to selected commodities from the Australian Bureau of Statistics 2000-01 and 2005 -2006 Agricultural Census. This survey is distributed online or via mail on a five-yearly basis to approximately 175,000 Agricultural business to ascertain information on a range of factors, such as types of crops, livestock and land preparation practices. For the purpose of this study we compared the land being used for total crops, and cereal , oil seed, legume, fruit and vegetable crops separately. Data was analysed using repeated measures anova in spss. Results: Overall, total area available for crops in urbanised areas of Australia increased slightly by 1.8%. However, Sydney, Melbourne, Adelaide and Perth experienced decreases in the area available for fruit crops by 11%, 5%,and 4% respectively. Furthermore, Brisbane and Perth experienced decreases in land available for vegetable crops by 28% and 14% respectively. Finally, Sydney, Adelaide and Perth experienced decreases in land available for cereal crops by 10 – 79%. Conclusions: These findings suggest that population increases and consequent urban sprawl may be resulting in a decrease in peri-urban agriculture, specifically for several core food groups including fruit, breads and grain based foods. In doing so, access to or availability of these foods may be limited, and the cost of these foods is likely to increase, which may compromise food insecurity for certain sub-groups of the population.

An analysis of the corporate governance practices of smaller listed Australian companies

We examine the corporate governance environment of smaller listed Australian firms to investigate the factors that determine how firms respond to recommendations contained in corporate governance codes. We group corporate governance recommendations into three distinct categories and argue that differences in adoption costs between categories, together with firm specific factors, determine a firm’s decision to conform with the recommendation or to explain the reasons for non-conformance. Analysis of the conformance by smaller firms with governance recommendations highlights substantial differences in adoption rates between categories of recommendations. Our results also reveal that the cost of adopting specific recommendations, together with profitability, external audit quality, and ownership dispersion, jointly explain a firm’s decision to ‘comply or explain’. This study provides insights for policy makers and regulators regarding the appropriateness of corporate governance recommendations for smaller firms

Modification of advanced programmatic risk analysis and management model for the whole project life cycle’s risks

The advanced programmatic risk analysis and management model (APRAM) is one of the recently developed methods that can be used for risk analysis and management purposes considering schedule, cost, and quality risks simultaneously. However, this model considers those failure risks that occur only over the design and construction phases of a project’s life cycle. While it can be sufficient for some projects for which the required cost during the operating life is much less than the budget required over the construction period, it should be modified in relation to infrastructure projects because the associated costs during the operating life cycle are significant. In this paper, a modified APRAM is proposed, which can consider potential risks that might occur over the entire life cycle of the project, including technical and managerial failure risks. Therefore, the modified model can be used as an efficient decision-support tool for construction managers in the housing industry in which various alternatives might be technically available. The modified method is demonstrated by using a real building project, and this demonstration shows that it can be employed efficiently by construction managers. The Delphi method was applied in order to figure out the failure events and their associated probabilities. The results show that although the initial cost of a cold-formed steel structural system is higher than a conventional construction system, the former’s failure cost is much lower than the latter’s