Dust emissions from a tunnel-ventilated broiler poultry shed with fresh and partially reused litter

Dust emissions from large-scale, tunnel-ventilated poultry sheds could have negative health and environmental impacts. Despite this fact, the literature concerning dust emissions from tunnel-ventilated poultry sheds in Australia and overseas is relatively scarce. Dust measurements were conducted during two consecutive production cycles at a single broiler shed on a poultry farm near Ipswich, Queensland. Fresh litter was employed during the first cycle and partially reused litter was employed during the second cycle. This provided an opportunity to study the effect that partial litter reuse has on dust emissions. Dust levels were characterised by the number concentration of suspended particles having diameter between 0.5–20 μm and by the mass concentration of dust particles below 10 μm diameter (PM10) and 2.5 μm diameter (PM2.5). In addition, we measured the number size distributions of dust particles. The average concentration and emission rate of dust was higher when partially reused litter was used in the shed than when fresh litter was used. In addition we found that dust particles emitted from the shed with partially reused litter were finer than the particles emitted with fresh litter. Although the change in litter properties is certainly contributing to this observed variability, other factors such as ventilation rate and litter moisture content are also likely to be involved.

Visualisation modelling in 3D of an alluvial aquifer system at a valley-wide scale to understand groundwater status : Lockyer, QLD

Visualisation provides a method to efficiently convey and understand the complex nature and processes of groundwater systems. This technique has been applied to the Lockyer Valley to aid in comprehending the current condition of the system. The Lockyer Valley in southeast Queensland hosts intensive irrigated agriculture sourcing groundwater from alluvial aquifers. The valley is around 3000 km2 in area and the alluvial deposits are typically 1-3 km wide and to 20-35 m deep in the main channels, reducing in size in subcatchments. The configuration of the alluvium is of a series of elongate “fingers”. In this roughly circular valley recharge to the alluvial aquifers is largely from seasonal storm events, on the surrounding ranges. The ranges are overlain by basaltic aquifers of Tertiary age, which overall are quite transmissive. Both runoff from these ranges and infiltration into the basalts provided ephemeral flow to the streams of the valley. Throughout the valley there are over 5,000 bores extracting alluvial groundwater, plus lesser numbers extracting from underlying sandstone bedrock. Although there are approximately 2500 monitoring bores, the only regularly monitored area is the formally declared management zone in the lower one third. This zone has a calibrated Modflow model (Durick and Bleakly, 2000); a broader valley Modflow model was developed in 2002 (KBR), but did not have extensive extraction data for detailed calibration. Another Modflow model focused on a central area river confluence (Wilson, 2005) with some local production data and pumping test results. A recent subcatchment simulation model incorporates a network of bores with short-period automated hydrographic measurements (Dvoracek and Cox, 2008). The above simulation models were all based on conceptual hydrogeological models of differing scale and detail.

Algebraic analysis of small Scale LEX-BES

This work examines the algebraic cryptanalysis of small scale variants of the LEX-BES. LEX-BES is a stream cipher based on the Advanced Encryption Standard (AES) block cipher. LEX is a generic method proposed for constructing a stream cipher from a block cipher, initially introduced by Biryukov at eSTREAM, the ECRYPT Stream Cipher project in 2005. The Big Encryption System (BES) is a block cipher introduced at CRYPTO 2002 which facilitates the algebraic analysis of the AES block cipher. In this article, experiments were conducted to find solutions of equation systems describing small scale LEX-BES using Gröbner Basis computations. This follows a similar approach to the work by Cid, Murphy and Robshaw at FSE 2005 that investigated algebraic cryptanalysis on small scale variants of the BES. The difference between LEX-BES and BES is that due to the way the keystream is extracted, the number of unknowns in LEX-BES equations is fewer than the number in BES. As far as the authors know, this attempt is the first at creating solvable equation systems for stream ciphers based on the LEX method using Gröbner Basis computations.

Examination of the latent structure of the psychological sense of school membership scale

Despite its widespread use, there has been limited examination of the underlying factor structure of the Psychological Sense of School Membership (PSSM) scale. The current study examined the psychometric properties of the PSSM to refine its utility for researchers and practitioners using a sample of 504 Australian high school students. Results from exploratory and confirmatory factor analyses indicated that the PSSM is a multidimensional instrument. Factor analysis procedures identified three factors representing related aspects of students’ perceptions of their school membership: caring relationships, acceptance, and rejection

Safety in occupational driving : development of a driver behaviour scale for the workplace context

International statistics indicate that occupational, or work-related driving, crashes are the most common cause of workplace injury, death, and absence from work. The majority of research examining unsafe driver behavior in the workplace has relied on general road safety questionnaires. However, past research has failed to consider the organizational context in the use of these questionnaires, and as such, there is ambiguity in the dimensions constituting occupational driving. Using a theoretical model developed by Hockey (1993, 1997), this article proposes and validates a new scale of occupational driver behavior. This scale incorporates four dimensions of driver behavior that are influenced by demanding workplace conditions; speeding, rule violation, inattention, and driving while tired. Following a content validation process, three samples of occupational drivers in Australia were used to assess the scale. Data from the first sample (n=145) were used to reduce the number of scale items and provide an assessment of the factorial validity of the scale. Data from the second sample (n=645) were then used to confirm the factor structure and psychometric properties of the scale including reliability and construct validity. Finally, data from the third sample (n=248) were used to establish criterion validity. The results indicated that the scale is a reliable and valid measure of occupational driver behavior.

Older adults’ safety perceptions of driving situations: Towards a new driving self-regulation scale

The term ‘driving self-restriction’ is used in the road safety literature to describe the behaviour of some older drivers. It includes the notion that older drivers will avoid driving in specific, usually self-identified situations, such as those in which safety is compromised. We sought to identify the situations that older drivers report avoiding; and, to determine the adequacy of a key measure of such behaviour. A sample of 75 drivers aged 65 years and older completed Baldock et al.’s modification of the Driving Habits Questionnaire avoidance items (Baldock et al., 2006), the Driving Behaviour Questionnaire, and open-ended items that elicited written descriptions of the most and least safe driving situation. Consistent with previous results, we found a relatively low level of driving self-restriction and infrequent episodes of aggressive violations. However, when combined with the situation descriptions, these data suggest that Driving Habits Questionnaire did not cover all of the situations that older drivers might choose avoid. We suggest that a new avoidance scale is needed and we present a new item pool that may be used for this purpose.

Lean project management in large scale industrial project via standardization

Lean project management is the comprehensive adaption of other lean concept like lean construction, lean manufacturing and lean thinking into project management context. Execution of many similar industrial projects creates the idea of lean project management in companies and rapidly growing in industries. This paper offers the standardization method in order to achieve Lean project management in large scale industrial project. Standardization refers to all activity which makes two projects most identical and unify to each other like standardization of design, reducing output variability, value analysis and strategic management. Although standard project may have minor effi ciency decrease, compare to custom built project; but great advantage of standard project like cost saving, time reduction and quality improvement justify standardization methodology. This paper based on empirical experience in industrial project and theoretical analysis of benefi ts of project standardization.

A coupled meshless technique/molecular dynamics approach for deformation characterization of monocrystalline metal

This paper presents a multiscale study using the coupled Meshless technique/Molecular Dynamics (M2) for exploring the deformation mechanism of mono-crystalline metal (focus on copper) under uniaxial tension. In M2, an advanced transition algorithm using transition particles is employed to ensure the compatibility of both displacements and their gradients, and an effective local quasi-continuum approach is also applied to obtain the equivalent continuum strain energy density based on the atomistic poentials and Cauchy-Born rule. The key parameters used in M2 are firstly investigated using a benchmark problem. Then M2 is applied to the multiscale simulation for a mono-crystalline copper bar. It has found that the mono-crystalline copper has very good elongation property, and the ultimate strength and Young's modulus are much higher than those obtained in macro-scale.

The Behaviour of Young Novice Drivers Scale (BYNDS)

The contribution of risky behaviour to the increased crash and fatality rates of young novice drivers is recognised in the road safety literature around the world. Exploring such risky driver behaviour has led to the development of tools like the Driver Behaviour Questionnaire (DBQ) to examine driving violations, errors, and lapses. Whilst the DBQ has been utilised in young novice driver research, some items within this tool seem specifically designed for the older, more experienced driver, whilst others appear to asses both behaviour and related motives. Therefore there is a need for a risky behaviour measurement tool that can be utilised with young drivers with a provisional (intermediate) driving licence.

The obsessive compulsive drinking scale is a valid measure of alcohol craving in young adults

Background: Alcohol craving is associated with greater alcohol-related problems and less favorable treatment prognosis. The Obsessive Compulsive Drinking Scale (OCDS) is the most widely used alcohol craving instrument. The OCDS has been validated in adults with alcohol use disorders (AUDs), which typically emerge in early adulthood. This study examines the validity of the OCDS in a nonclinical sample of young adults. Methods: Three hundred and nine college students (mean age of 21.8 years, SD = 4.6 years) completed the OCDS, Alcohol Use Disorders Identification Test (AUDIT), and measures of alcohol consumption. Subjects were randomly allocated to 2 samples. Construct validity was examined via exploratory factor analysis (n = 155) and confirmatory factor analysis (n = 154). Concurrent validity was assessed using the AUDIT and measures of alcohol consumption. A second, alcohol-dependent sample (mean age 42 years, SD 12 years) from a previously published study (n = 370) was used to assess discriminant validity. Results: A unique young adult OCDS factor structure was validated, consisting of Interference/Control, Frequency of Obsessions, Alcohol Consumption and Resisting Obsessions/Compulsions. The young adult 4-factor structure was significantly associated with the AUDIT and alcohol consumption. The 4 factor OCDS successfully classified nonclinical subjects in 96.9% of cases and the older alcohol-dependent patients in 83.7% of cases. Although the OCDS was able to classify college nonproblem drinkers (AUDIT <13, n = 224) with 83.2% accuracy, it was no better than chance (49.4%) in classifying potential college problem drinkers (AUDIT score ≥13, n = 85). Conclusions: Using the 4-factor structure, the OCDS is a valid measure of alcohol craving in young adult populations. In this nonclinical set of students, the OCDS classified nonproblem drinkers well but not problem drinkers. Studies need to further examine the utility of the OCDS in young people with alcohol misuse.

Large-scale fabrication of H2(H2O)Nb2O6 and Nb2O5 hollow microspheres

Hollow micro-sized H2(H2O)Nb2O6 spheres constructed by nanocrystallites have been successfully synthesized via a bubble-template assisted hydrothermal process. In the reaction process, H2O2 acts as a bubble generator and plays a key role in the formation of the hollow structure. An in situ bubble-template mechanism has been proposed for the possible formation of the hollow structure. The spherelike assemblies of these H2(H2O)Nb2O6 nanoparticles have been transformed into their corresponding pseudohexagonal phase Nb2O5 through a moderate annealing dehydration process without destroying the hierarchical structure. Optical properties of the as-prepared hollow spheres were investigated. It is exciting that the absorption edge of the hollow Nb2O5 microspheres shifts about 18 nm to the violet compared with bulk powders in the UV/vis spectra, indicating its superior optical properties.

Electrospraying a reproducible method for production of polymeric microspheres for biomedical applications

The ability to reproducibly load bioactive molecules into polymeric microspheres is a challenge. Traditional microsphere fabrication methods typically provide inhomogeneous release profiles and suffer from lack of batch to batch reproducibility, hindering their potential to up-scale and their translation to the clinic. This deficit in homogeneity is in part attributed to broad size distributions and variability in the morphology of particles. It is thus desirable to control morphology and size of non-loaded particles in the first instance, in preparation for obtaining desired release profiles of loaded particles in the later stage. This is achieved by identifying the key parameters involved in particle production and understanding how adapting these parameters affects the final characteristics of particles. In this study, electrospraying was presented as a promising technique for generating reproducible particles made of polycaprolactone, a biodegradable, FDA-approved polymer. Narrow size distributions were obtained by the control of electrospraying flow rate and polymer concentration, with average particle sizes ranging from 10 to 20 um. Particles were shown to be spherical with a homogenous embossed texture, determined by the polymer entanglement regime taking place during electrospraying. No toxic residue was detected by this process based on preliminary cell work using DNA quantification assays, validating this method as suitable for further loading of bioactive components.

Remote monitoring of outdoor performance of low scale dye sensitized solar cells for nanosensors nodes

This is the first outdoor test of small-scale dye sensitized solar cells (DSC) powering a standalone nanosensor node. A solar cell test station (SCTS) has been developed using standard DSC to power a gas nanosensor, a radio transmitter, and the control electronics (CE) for battery charging. The station is remotely monitored through wired (Ethernet cable) or wireless connection (radio transmitter) in order to evaluate in real time the performance of the solar cells powering a nanosensor and a transmitter under different weather conditions. We analyze trends of energy conversion efficiency after 60 days of operation. The 408 cm2 active surface module produces enough energy to power a gas nanosensor and a radio transmitter during the day and part of the night. Also, by using a variable programmable load we keep the system working on the maximum power point (MPP) quantifying the total energy generated and stored in a battery. Although this technology is at an early stage of development, these experiments provide useful data for future outdoor applications such as nanosensor network nodes.

Remote monitoring of outdoor performance of low scale dye sensitized solar cells for nanosensors nodes

This is the first outdoor test of small-scale dye sensitized solar cells (DSC) powering a stand-alone nanosensor node. A solar cell test station (SCTS) has been developed using standard DSC to power a gas nanosensor, a radio transmitter, and the control electronics (CE) for battery charging. The station is remotely monitored through wired (Ethernet cable) or wireless connection (radio transmitter) in order to evaluate in real time the performance of the solar cells and devices under different weather conditions. The 408 cm2 active surface module produces enough energy to power a gas nanosensor and a radio transmitter during the day and part of the night. Also, by using a programmable load we keep the system working on the maximum power point (MPP) quantifying the total energy generated and stored in a battery. These experiments provide useful data for future outdoor applications such as nanosensor networks.

Developing a multidimensional scale for ethical decision making

This article reports on the development of the managerial ethical profile (MEP) scale. The MEP scale is a multilevel, self-reporting scale measuring the perceived influence that different dimensions of common ethical frameworks have on managerial decision making. The MEP scale measures on eight subscales: economic egoism, reputational egoism, act utilitarianism, rule utilitarianism, self-virtue of self, virtue of others, act deontology, and rule deontology. Confirmatory factor analysis (CFA) was used to provide evidence of scale validity. Future research needs and the value of this measure for business ethics are discussed.