Non-invasive method for detecting changes in soil moisture using wireless sensor networks

There are several popular soil moisture measurement methods today such as time domain reflectometry, electromagnetic (EM) wave, electrical and acoustic methods. Significant studies have been dedicated in developing method of measurements using those concepts, especially to achieve the characteristics of noninvasiveness. EM wave method provides an advantage because it is non-invasive to the soil and does not need to utilise probes to penetrate or bury in the soil. But some EM methods are also too complex, expensive, and not portable for the application of Wireless Sensor Networks; for example satellites or UAV (Unmanned Aerial Vehicle) based sensors. This research proposes a method in detecting changes in soil moisture using soil-reflected electromagnetic (SREM) wave from Wireless Sensor Networks (WSNs). Studies have shown that different levels of soil moisture will affects soil’s dielectric properties, such as relative permittivity and conductivity, and in turns change its reflection coefficients. The SREM wave method uses a transmitter adjacent to a WSNs node with purpose exclusively to transmit wireless signals that will be reflected by the soil. The strength from the reflected signal that is determined by the soil’s reflection coefficients is used to differentiate the level of soil moisture. The novel nature of this method comes from using WSNs communication signals to perform soil moisture estimation without the need of external sensors or invasive equipment. This innovative method is non-invasive, low cost and simple to set up. There are three locations at Brisbane, Australia chosen as the experiment’s location. The soil type in these locations contains 10–20% clay according to the Australian Soil Resource Information System. Six approximate levels of soil moisture (8, 10, 13, 15, 18 and 20%) are measured at each location; with each measurement consisting of 200 data. In total 3600 measurements are completed in this research, which is sufficient to achieve the research objective, assessing and proving the concept of SREM wave method. These results are compared with reference data from similar soil type to prove the concept. A fourth degree polynomial analysis is used to generate an equation to estimate soil moisture from received signal strength as recorded by using the SREM wave method.

Is language a barrier for quality care in hospitals? A case series from an Emergency Department of a teaching hospital in Brisbane

Aim: The aim of this pilot study is to describe the use of an Emergency Department (ED) at a large metropolitan teaching hospital by patients who speak English or other languages at home. Methods: All data were retrieved from the Emergency Department Information System (EDIS) of this tertiary teaching hospital in Brisbane. Patients were divided into two groups based on the language spoken at home: patients who speak English only at home (SEO) and patients who do not speak English only or speak other language at home (NSEO). Modes of arrival, length of ED stay and the proportion of hospital admission were compared among the two groups of patients by using SPSS V18 software. Results: A total of 69,494 patients visited this hospital ED in 2009 with 67,727 (97.5%) being in the SEO group and 1,281 (1.80%) in the NSEO group. The proportion of ambulance utilisation in arrival mode was significantly higher among SEO 23,172 (34.2%) than NSEO 397 (31.0%), p <0.05. The NSEO patients had longer length of stay in the ED (M = 337.21, SD = 285.9) compared to SEO patients (M= 290.9, SD = 266.8), with 46.3 minutes (95%CI 62.1, 30.5, p <0.001) difference. The admission to the hospital among NSEO was 402 (31.9%) higher than SEO 17,652 (26.6%), p <0.001. Conclusion: The lower utilisation rates of ambulance services, longer length of ED stay and higher hospital admission rates in NSEO patients compared to SEO patients are consistent with other international studies and may be due to the language barriers.

What health problems overcrowd hospital emergency departments in Queensland and has this changed over time? A case study of two hospitals in Queensland 2001 - 2009

Aim: to describe what health problems patients attending emergency department with and whether this changed over time. Methods: Electronic data was retrieved from EDIS (Emergency Department Information System) and HBCIS (Hospital Based Clinical Information System) in two hospitals in Queensland in the period 2001-2009. The ICD-10 code of patient's diagnosis was then extrapolated and then group into ICD-10 chapters, such that the health problem can be presented. Results: Among the specific health problems, Chapter XIX 'Injury and poisoning' ranked number one consistently (ranging from 22.1% to 31.2% of the total presentations) in both the urban and remote hospitals in Queensland. The top ten specific presenting health problems in both the urban and remote hospital include Chapter XI 'Digestive system', Chapter XIV 'Genitourinary system', Chapter IX 'Circulatory system', and Chapter XIII 'Musculoskeletal system and connective tissue'. Chapter X 'Respiratory system' made the top ten presenting Chapters in both hospitals, but ranked much higher (number four consistently for the eight years, ranging from 6.8% to 8.3%) in the remote hospital. Chapter XV 'Pregnancy childbirth and puerperium' made to the top ten in the urban hospital only while Chapter XII 'Skin and subcutaneous tissue', Chapter I 'Infectious and parasitic diseases' made the top ten in the remote hospital only. Conclusion: The number one health problem presenting to both the urban and remote hospitals in Queensland is Chapter XIX 'Injury and poisoning', and it did not change in the period 211 - 2009.

Spatio-temporal patterns of Barmah Forest virus disease in Queensland, Australia

Background Barmah Forest virus (BFV) disease is a common and wide-spread mosquito-borne disease in Australia. This study investigated the spatio-temporal patterns of BFV disease in Queensland, Australia using geographical information system (GIS) tools and geostatistical analysis. Methods/Principal Findings We calculated the incidence rates and standardised incidence rates of BFV disease. Moran's I statistic was used to assess the spatial autocorrelation of BFV incidences. Spatial dynamics of BFV disease was examined using semi-variogram analysis. Interpolation techniques were applied to visualise and display the spatial distribution of BFV disease in statistical local areas (SLAs) throughout Queensland. Mapping of BFV disease by SLAs reveals the presence of substantial spatio-temporal variation over time. Statistically significant differences in BFV incidence rates were identified among age groups (χ2 = 7587, df = 7327,p<0.01). There was a significant positive spatial autocorrelation of BFV incidence for all four periods, with the Moran's I statistic ranging from 0.1506 to 0.2901 (p<0.01). Semi-variogram analysis and smoothed maps created from interpolation techniques indicate that the pattern of spatial autocorrelation was not homogeneous across the state. Conclusions/Significance This is the first study to examine spatial and temporal variation in the incidence rates of BFV disease across Queensland using GIS and geostatistics. The BFV transmission varied with age and gender, which may be due to exposure rates or behavioural risk factors. There are differences in the spatio-temporal patterns of BFV disease which may be related to local socio-ecological and environmental factors. These research findings may have implications in the BFV disease control and prevention programs in Queensland.

Sustainable Road Management in Texas : network-level flexible pavement structural condition analysis using data mining techniques

The research team recognized the value of network-level Falling Weight Deflectometer (FWD) testing to evaluate the structural condition trends of flexible pavements. However, practical limitations due to the cost of testing, traffic control and safety concerns and the ability to test a large network may discourage some agencies from conducting the network-level FWD testing. For this reason, the surrogate measure of the Structural Condition Index (SCI) is suggested for use. The main purpose of the research presented in this paper is to investigate data mining strategies and to develop a prediction method of the structural condition trends for network-level applications which does not require FWD testing. The research team first evaluated the existing and historical pavement condition, distress, ride, traffic and other data attributes in the Texas Department of Transportation (TxDOT) Pavement Maintenance Information System (PMIS), applied data mining strategies to the data, discovered useful patterns and knowledge for SCI value prediction, and finally provided a reasonable measure of pavement structural condition which is correlated to the SCI. To evaluate the performance of the developed prediction approach, a case study was conducted using the SCI data calculated from the FWD data collected on flexible pavements over a 5-year period (2005 – 09) from 354 PMIS sections representing 37 pavement sections on the Texas highway system. The preliminary study results showed that the proposed approach can be used as a supportive pavement structural index in the event when FWD deflection data is not available and help pavement managers identify the timing and appropriate treatment level of preventive maintenance activities.

Putting the Repository First: Implementing a Repository to RIS Workflow for QUT ePrints

As one of the first institutional repositories in Australia and the first in the world to have an institution-wide deposit mandate, QUT ePrints has great ‘brand recognition’ within the University (Queensland University of Technology) and beyond. The repository is managed by the library but, over the years, the Library’s repository team has worked closely with other departments (especially the Office of Research and IT Services) to ensure that QUT ePrints was embedded into the business processes and systems our academics use regularly. For example, the repository is the source of the publication information which displays on each academic’s Staff Profile page. The repository pulls in citation data from Scopus and Web of Science and displays the data in the publications records. Researchers can monitor their citations at a glance via the repository ‘View’ which displays all their publications. A trend in recent years has been to populate institutional repositories with publication details imported from the University’s research information system (RIS). The main advantage of the RIS to Repository workflow is that it requires little input from the academics as the publication details are often imported into the RIS from publisher databases. Sadly, this is also its main disadvantage. Generally, only the metadata is imported from the RIS and the lack of engagement by the academics results in very low proportions of records with open access full-texts. Consequently, while we could see the value of integrating the two systems, we were determined to make the repository the entry point for publication data. In 2011, the University funded a project to convert a number of paper-based processes into web-based workflows. This included a workflow to replace the paper forms academics used to complete to report new publications (which were later used by the data entry staff to input the details into the RIS). Publication details and full-text files are uploaded to the repository (by the academics or their nominees). Each night, the repository (QUT ePrints) pushes the metadata for new publications into a holding table. The data is checked by Office of Research staff the next day and then ‘imported’ into the RIS. Publication details (including the repository URLs) are pushed from the RIS to the Staff Profiles system. Previously, academics were required to supply the Office of research with photocopies of their publication (for verification/auditing purposes). The repository is now the source of verification information. Library staff verify the accuracy of the publication details and, where applicable, the peer review status of the work. The verification metadata is included in the information passed to the Office of Research. The RIS at QUT comprises two separate systems built on an Oracle database; a proprietary product (ResearchMaster) plus a locally produced system known as RAD (Research Activity Database). The repository platform is EPrints which is built on a MySQL database. This partly explains why the data is passed from one system to the other via a holding table. The new workflow went live in early April 2012. Tests of the technical integration have all been successful. At the end of the first 12 months, the impact of the new workflow on the proportion of full-texts deposited will be evaluated.

Development of network-level project screening methods supporting the 4-Year pavement management plan in Texas

The Texas Department of Transportation (TxDOT) is concerned about the widening gap between pavement preservation needs and available funding. Thus, the TxDOT Austin District Pavement Engineer (DPE) has investigated methods to strategically allocate available pavement funding to potential projects that improve the overall performance of the District and Texas highway systems. The primary objective of the study presented in this paper is to develop a network-level project screening and ranking method that supports the Austin District 4-year pavement management plan development. The study developed candidate project selection and ranking algorithms that evaluated pavement conditions of each project candidate using data contained in the Pavement Management Information system (PMIS) database and incorporated insights from Austin District pavement experts; and implemented the developed method and supporting algorithm. This process previously required weeks to complete, but now requires about 10 minutes including data preparation and running the analysis algorithm, which enables the Austin DPE to devote more time and resources to conducting field visits, performing project-level evaluation and testing candidate projects. The case study results showed that the proposed method assisted the DPE in evaluating and prioritizing projects and allocating funds to the right projects at the right time.

Impact of a government triple zero awareness campaign on emergency department patient characteristics

Objective: To evaluate the impact of a government triple zero community awareness campaign on the characteristics of patients attending an ED. Methods: A study using Emergency Department Information System data was conducted in an adult metropolitan tertiary-referral teaching hospital in Brisbane. The three outcomes measured in the 3 month post-campaign period were arrival mode, Australasian Triage Scale and departure status. These measures reflect ambulance usage, clinical urgency and illness severity, respectively. They were compared with those in the 3 month pre-campaign period. Multivariate logistic regression models were used to investigate the impacts of the campaign on each of the three outcome measures after controlling for age, sex, day and time of arrival, and daily minimum temperature. Results: There were 17 920 visits in the pre- and 17 793 visits in the post-campaign period. After the campaign, fewer patients arrived at the ED by road ambulance (odds ratio [OR] 0.90, 95% confidence interval [CI] 0.80–1.00), although the impact of the campaign on the arrival mode was only close to statistical significance (Wald χ2-test, P= 0.055); and patients were significantly less likely to have higher clinical urgency (OR 0.86, 95% CI 0.79–0.94), while more likely to be admitted (OR 1.68, 95% CI 1.38–2.05) or complete treatment in the ED (OR 1.46, 95% CI 1.23–1.73) instead of leaving without waiting to be seen. Conclusions: The campaign had no significant impact on the arrival mode of the patients. After the campaign, the illness acuity of the patients decreased, whereas the illness severity of the patients increased.

Spatial and temporal distribution of falciparum malaria in China

Background: Falciparum malaria is the most deadly among the four main types of human malaria. Although great success has been achieved since the launch of the National Malaria Control Programme in 1955, malaria remains a serious public health problem in China. This paper aimed to analyse the geographic distribution, demographic patterns and time trends of falciparum malaria in China. Methods: The annual numbers of falciparum malaria cases during 1992–2003 and the individual case reports of each clinical falciparum malaria during 2004–2005 were extracted from communicable disease information systems in China Center for Diseases Control and Prevention. The annual number of cases and the annual incidence were mapped by matching them to corresponding province- and county-level administrative units in a geographic information system. The distribution of falciparum malaria by age, gender and origin of infection was analysed. Time-series analysis was conducted to investigate the relationship between the falciparum malaria in the endemic provinces and the imported falciparum malaria in non-endemic provinces. Results: Falciparum malaria was endemic in two provinces of China during 2004–05. Imported malaria was reported in 26 non-endemic provinces. Annual incidence of falciparum malaria was mapped at county level in the two endemic provinces of China: Yunnan and Hainan. The sex ratio (male vs. female) for the number of cases in Yunnan was 1.6 in the children of 0–15 years and it reached 5.7 in the adults over 15 years of age. The number of malaria cases in Yunnan was positively correlated with the imported malaria of concurrent months in the non-endemic provinces. Conclusion: The endemic area of falciparum malaria in China has remained restricted to two provinces, Yunnan and Hainan. Stable transmission occurs in the bordering region of Yunnan and the hilly-forested south of Hainan. The age and gender distribution in the endemic area is characterized by the predominance of adult men cases. Imported falciparum malaria in the non-endemic area of China, affected mainly by the malaria transmission in Yunnan, has increased both spatially and temporally. Specific intervention measures targeted at the mobile population groups are warranted.

Emergency Health Services (EHS) : demand and service delivery models. [Monograph 2 : Queensland EHS users’ profile]

Emergency health is a critical component of Australia’s health system and one which is increasingly congested from growing demand and blocked access to inpatient beds. The Emergency Health Services Queensland (EHSQ) study aims to identify the factors driving increased demand for emergency health and to evaluate strategies which may safely reduce the future demand growth. This monograph addresses the characteristics of users of emergency health services with an aim to identify those that appear to contribute to demand growth. This study utilises data on patients treated by Emergency Departments (ED) and Queensland Ambulance Service (QAS) across Queensland. ED data was derived from the Emergency Department Information System (EDIS) for the period 2001-02 through to 2010-11. Ambulance data was extracted from the QAS’ Ambulance Information Management System (AIMS) and electronic Ambulance Report Form (eARF) for the period 2001-02 through to 2009-10. Due to discrepancies and comparability issues for ED data, this monograph compares data from the 2003-04 time period with 2010-11 data for 21 of the reporting EDs. Also a snapshot of users for the 2010-11 financial year for 31 reporting EDs is used to describe the characteristics of users and to compare those characteristics with population demographics. For QAS data, the 2002-03 and 2009-10 time periods were selected for detailed analyses to identify trends. • Demand for emergency health care services is increasing, representing both increased population and increased relative utilisation. Per capita demand for ED attention has increased by 2% per annum over the last decade and for ambulance attention by 3.7% per annum. • The growth in ED demand is prominent in more urgent triage categories with actual decline in less urgent patients. An estimated 55% of patients attend hospital EDs outside of normal working hours. There is no evidence that patients presenting out of hours are significantly different to those presenting within working hours; they have similar triage assessments and outcomes. • Patients suffering from injuries and poisoning comprise 28% of the ED workload (an increase of 65% in the study period), whilst declines of 32% in cardiovascular and circulatory conditions, and musculoskeletal problems have been observed. • 25.6% of patients attending EDs are admitted to hospital. 19% of admitted patients and 7% of patients who die in the ED are triage category 4 or 5 on arrival. • The average age of ED patients is 35.6 years. Demand has grown in all age groups and amongst both men and women. Men have higher utilisation rates for ED in all age groups. The only group where the growth rate in women has exceeded men is in the 20-29 age group; this growth is particularly in the injury and poisoning categories. • Considerable attention has been paid publicly to ED performance criteria. It is worth noting that 50% of all patients were treated within 33 minutes of arrival. • Patients from lower socioeconomic areas appear to have higher utilisation rates and the utilisation rate for indigenous people appears to exceed those of European and other backgrounds. The utilisation rates for immigrant people is generally less than that of Australian born however it has not been possible to eliminate the confounding impact of different age and socioeconomic profiles. • Demand for ambulance service is also increasing at a rate that exceeds population growth. Utilisation rates have increased by an average of 5% per annum in Queensland compared to 3.6% nationally, and the utilisation rate in Queensland is 27% higher than the national average. • The growth in ambulance utilisation has also been amongst the more urgent categories of dispatch and utilisation rates are higher in rural and regional areas than in the metropolitan area. The demand for ambulance increases with age but the growth in demand for ambulance service has been more prominent in younger age groups. These findings contribute significantly to an understanding of the growth in demand for emergency health. It shows that the growth is amongst patients in genuine need of emergency healthcare and public rhetoric that the congestion of emergency health services is due to inappropriate attendees is unable to be substantiated. The consistency of the growth in demand over the last decade reflects not only the changing demographics of the Australian population but also the changes in health status, standards of acute health care and other social factors. The growth is also amongst patients with acute injury and poisoning which is inconsistent with rates of chronic disease as a fundamental driver. We have also interviewed patients in regard to their decision making choices for acute health care and the factors that influence these decisions and this will be the subject of a third Monograph and publications.

Improving self care of patients with chronic disease using online personal health record

BACKGROUND: Effective management of chronic diseases such as prostate cancer is important. Research suggests a tendency to use self-care treatment options such as over-the-counter (OTC) complementary medications among prostate cancer patients. The current trend in patient-driven recording of health data in an online Personal Health Record (PHR) presents an opportunity to develop new data-driven approaches for improving prostate cancer patient care. However, the ability of current online solutions to share patients' data for better decision support is limited. An informatics approach may improve online sharing of self-care interventions among these patients. It can also provide better evidence to support decisions made during their self-managed care. AIMS: To identify requirements for an online system and describe a new case-based reasoning (CBR) method for improving self-care of advanced prostate cancer patients in an online PHR environment. METHOD: A non-identifying online survey was conducted to understand self-care patterns among prostate cancer patients and to identify requirements for an online information system. The pilot study was carried out between August 2010 and December 2010. A case-base of 52 patients was developed. RESULTS: The data analysis showed self-care patterns among the prostate cancer patients. Selenium (55%) was the common complementary supplement used by the patients. Paracetamol (about 45%) was the commonly used OTC by the patients. CONCLUSION: The results of this study specified requirements for an online case-based reasoning information system. The outcomes of this study are being incorporated in design of the proposed Artificial Intelligence (Al) driven patient journey browser system. A basic version of the proposed system is currently being considered for implementation.

Spatial clusters of suicide in Australia

Background: Understanding the spatial distribution of suicide can inform the planning, implementation and evaluation of suicide prevention activity. This study explored spatial clusters of suicide in Australia, and investigated likely socio-demographic determinants of these clusters. Methods: National suicide and population data at a statistical local area (SLA) level were obtained from the Australian Bureau of Statistics for the period of 1999 to 2003. Standardised mortality ratios (SMR) were calculated at the SLA level, and Geographic Information System (GIS) techniques were applied to investigate the geographical distribution of suicides and detect clusters of high risk in Australia. Results: Male suicide incidence was relatively high in the northeast of Australia, and parts of the east coast, central and southeast inland, compared with the national average. Among the total male population and males aged 15 to 34, Mornington Shire had the whole or a part of primary high risk cluster for suicide, followed by the Bathurst-Melville area, one of the secondary clusters in the north coastal area of the Northern Territory. Other secondary clusters changed with the selection of cluster radius and age group. For males aged 35 to 54 years, only one cluster in the east of the country was identified. There was only one significant female suicide cluster near Melbourne while other SLAs had very few female suicide cases and were not identified as clusters. Male suicide clusters had a higher proportion of Indigenous population and lower median socio-economic index for area (SEIFA) than the national average, but their shapes changed with selection of maximum cluster radii setting. Conclusion: This study found high suicide risk clusters at the SLA level in Australia, which appeared to be associated with lower median socio-economic status and higher proportion of Indigenous population. Future suicide prevention programs should focus on these high risk areas.

Language and utilisation of emergency care in Queensland

Objective: To compare access and utilisation of EDs in Queensland public hospitals between people who speak only English at home and those who speak another language at home. Methods: A retrospective analysis of a Queensland statewide hospital ED dataset (ED Information System) from 1 January 2008 to 31 December 2010 was conducted. Access to ED care was measured by the proportion of the state’s population attending EDs. Logistic regression analyses were performed to determine the relationships between ambulance use and language, and between hospital admission and language, both after adjusting for age, sex and triage category. Results: The ED utilisation rate was highest in English only speakers (290 per 1000 population), followed by Arabic speakers (105), and lowest among German speakers (30). Compared with English speakers, there were lower rates of ambulance use in Chinese (odds ratio 0.50, 95% confidence interval, 0.47–0.54), Vietnamese (0.87, 0.79–0.95), Arabic (0.87, 0.78–0.97), Spanish (0.56, 0.50–0.62), Italian (0.88, 0.80–0.96), Hindi (0.61, 0.53–0.70) and German (0.87, 0.79–0.90) speakers. Compared with English speakers, German speakers had higher admission rates (odds ratio 1.17, 95% confidence interval, 1.02–1.34), whereas there were lower admission rates in Chinese (0.90, 0.86–0.99), Arabic (0.76, 0.67–0.85) and Spanish (0.83, 0.75–0.93) speakers. Conclusion: This study showed that there was a significant association between lower utilisation of emergency care and speaking languages other than English at home. Further researches are needed using in-depth methodology to investigate if there are language barriers in accessing emergency care in Queensland.

A Comprehensive Benchmarking Framework (CoBeFra) for conformance analysis between procedural process models and event logs in ProM

Process mining encompasses the research area which is concerned with knowledge discovery from information system event logs. Within the process mining research area, two prominent tasks can be discerned. First of all, process discovery deals with the automatic construction of a process model out of an event log. Secondly, conformance checking focuses on the assessment of the quality of a discovered or designed process model in respect to the actual behavior as captured in event logs. Hereto, multiple techniques and metrics have been developed and described in the literature. However, the process mining domain still lacks a comprehensive framework for assessing the goodness of a process model from a quantitative perspective. In this study, we describe the architecture of an extensible framework within ProM, allowing for the consistent, comparative and repeatable calculation of conformance metrics. For the development and assessment of both process discovery as well as conformance techniques, such a framework is considered greatly valuable.