Atomistic exploration of deformation properties of copper nanowires with pre-existing defects

Based on the embedded atom method (EAM) and molecular dynamics (MD) method, in this paper, the tensile deformation properties of Cu nanowires (NWs) with different pre-existing defects, including single surface defects, surface bi-defects and single internal defects, are systematically studied. In-depth deformation mechanisms of NWs with pre-existing defects are also explored. It is found that Young's modulus is insensitive to different pre-existing defects, but yield strength shows an obvious decrease. Defects are observed influencing greatly on NWs' tensile deformation mechanisms, and playing a role of dislocation sources. Besides of the traditional deformation process dominated by the nucleation and propagation of partial dislocations, the generations of twins, grain boundaries, fivefold deformation twins, hexagonal close-packed (HCP) structure and phase transformation from face-centred cubic (FCC) structure to HCP structure have been triggered by pre-existing defects. It is found that surface defect intends to induce larger influence to yield strength than internal defect. Most importantly, the defect that lies on slip planes exerts larger influence than other defects. As expected, it is also found that the more or longer of the defect, the bigger influence will be induced.

Sub-tropical high-density, low rise residential buildings: case study 3

The case study 3 team viewed the mitigation of noise and air pollution generated in the transport corridor that borders the study site to be a paramount driver of the urban design solution. These key urban planning strategies were adopted: * Spatial separation from transport corridor pollution source. A linear green zone and environmental buffer was proposed adjacent to the transport corridor to mitigate the environmental noise and air quality impacts of the corridor, and to offer residents opportunities for recreation * Open space forming the key structural principle for neighbourhood design. A significant open space system underpins the planning and manages surface water flows. * Urban blocks running on east-west axis. The open space rationale emphasises an east-west pattern for local streets. Street alignment allows for predominantly north-south facing terrace type buildings which both face the street and overlook the green courtyard formed by the perimeter buildings. The results of the ESD assessment of the typologies conclude that the design will achieve good outcomes through: * Lower than average construction costs compared with other similar projects * Thermal comfort; A good balance between daylight access and solar gains is achieved * The energy rating achieved for the units is 8.5 stars.

Estimation of energy saving of commercial building by living wall and green facade in sub-tropical climate of Australia

This paper investigates energy saving potential of commercial building by living wall and green façade system using Envelope Thermal Transfer Value (ETTV) equation in Sub-tropical climate of Australia. Energy saving of four commercial buildings was quantified by applying living wall and green façade system to the west facing wall. A field experimental facility, from which temperature data of living wall system was collected, was used to quantify wall temperatures and heat gain under controlled conditions. The experimental parameters were accumulated with extensive data of existing commercial building to quantify energy saving. Based on temperature data of living wall system comprised of Australian native plants, equivalent temperature of living wall system has been computed. Then, shading coefficient of plants in green façade system has been included in mathematical equation and in graphical analysis. To minimize the air-conditioned load of commercial building, therefore to minimize the heat gain of commercial building, an analysis of building heat gain reduction by living wall and green façade system has been performed. Overall, cooling energy performance of commercial building before and after living wall and green façade system application has been examined. The quantified energy saving showed that only living wall system on opaque part of west facing wall can save 8-13 % of cooling energy consumption where as only green façade system on opaque part of west facing wall can save 9.5-18% cooling energy consumption of commercial building. Again, green façade system on fenestration system on west facing wall can save 28-35 % of cooling energy consumption where as combination of both living wall on opaque part of west facing wall and green façade on fenestration system on west facing wall can save 35-40% cooling energy consumption of commercial building in sub-tropical climate of Australia.

Study of the effectiveness of outrigger system for high-rise composite buildings for cyclonic region

The demands of taller structures are becoming imperative almost everywhere in the world in addition to the challenges of material and labor cost, project time line etc. This paper conducted a study keeping in view the challenging nature of high-rise construction with no generic rules for deflection minimizations and frequency control. The effects of cyclonic wind and provision of outriggers on 28-storey, 42-storey and 57-storey are examined in this paper and certain conclusions are made which would pave way for researchers to conduct further study in this particular area of civil engineering. The results show that plan dimensions have vital impacts on structural heights. Increase of height while keeping the plan dimensions same, leads to the reduction in the lateral rigidity. To achieve required stiffness increase of bracings sizes as well as introduction of additional lateral resisting system such as belt truss and outriggers is required.

Energy use, indoor temperature and possible adaptation strategies for air-conditioned office buildings in face of global warming

This paper discusses and summarises a recent systematic study on the implication of global warming on air conditioned office buildings in Australia. Four areas are covered, including analysis of historical weather data, generation of future weather data for the impact study of global warming, projection of building performance under various global warming scenarios, and evaluation of various adaptation strategies under 2070 high global warming conditions. Overall, it is found that depending on the assumed future climate scenarios and the location considered, the increase of total building energy use for the sample Australian office building may range from 0.4 to 15.1%. When the increase of annual average outdoor temperature exceeds 2 °C, the risk of overheating will increase significantly. However, the potential overheating problem could be completely eliminated if internal load density is significantly reduced.

Global Warming : Impact on Building Design and Performance

Global warming is entailing new climatic conditions for the built environment. Such a warming climate will affect both the performance of existing building stock and the design of new buildings. In this article, the knowledge of global warming and climate change is first introduced. The cycling interaction between global warming and buildings is then presented. The impact of global warming on building energy use and thermal performance is also assessed. Finally, the potential mitigation and adaptation strategies to the global warming are discussed.

Project 2.7 Leveraging R&D Investment for the Australian built environment : Phase 2 Case Study Report Part 3 - Green Buildings

This report discusses findings of a case study into "Green Buildings" undertaken as a part of the retrospective analysis component of Sustainable Built Environment National Research Centre (SBEnrc) Project 2.7 Leveraging R&D investment for the Australian Built Environment. The Western Australian Government (WAG) has taken a leadership role for a number of decades in developing more environmentally responsive buildings. In the past decade, considerable initiatives have been introduced to contribute to: (i) greening the stock of government buildings; and (ii) providing leadership in the development of other non-residential buildings developed commercially. This role has been informed by global, national and internal initiatives and research in this area. This case study investigates: (i) the nature of this leadership; and (ii) the role of R&D policy development; and (iii) the dissemination and impact of outcomes in the broader industry. This case study should be read in conjunction with Part 1 of this suite of reports.

Green buildings for greying people : a case study of a retirement village in Australia

Purpose With an increasingly ageing population and widespread acceptance of the need for sustainable development in Australia, the demand for green retirement villages is increasing. This paper aims to identify the critical issues to be considered by developers and practitioners when embarking on their first green residential retirement project in Australia. Design/methodology/approach In view of the lack of adequate historical data for quantitative analysis, a case study approach is employed to examine the successful delivery of green retirement villages. Face-to-face interviews and document analysis were conducted for data collection. Findings The findings of the study indicate that one of the major obstacles to the provision of affordable green retirement villages is the higher initial costs involved. However, positive aspects were identified, the most significant of which relate to: the innovative design of site and floor plans; adoption of thermally efficient building materials; orientation of windows; installation of water harvesting and recycling systems, water conservation fittings and appliances; and waste management during the construction stage. With the adoption of these measures, it is believed that sustainable retirement development can be achieved without significant additional capital costs. Practical implications The research findings serve as a guide for developers in decision making throughout the project life-cycle when introducing green features into the provision of affordable retirement accommodation. Originality/value This paper provides insights into the means by which affordable green residential retirement projects for aged people can be successfully completed.

New strategies of managing waste in office building retrofit projects

Retrofit projects are different from newly-built projects in many respects. A retrofit project involves an existing building, which imposes constraints on the owners, designers, operators and constructors throughout the project process. Retrofit projects are risky, complex, less predictable and difficult to be well planned, which need greater coordination. For office building retrofit project, further restrictions will apply as these buildings often locate in CBD areas and most have to remain operational during the progression of project work. Issues such as site space, material storage and handling, noise and dust, need to be considered and well addressed. In this context, waste management is even more challenging with small spaces for waste handling, uncertainties in waste control, and impact of waste management activities on project delivery and building occupants. Current literatures on waste management in office building retrofit projects focus on increasing waste recovery rate based on project planning, monitoring and stakeholders’ collaboration. However, previous research has not produced knowledge of understanding the particular retrofit processes and their impact on waste generation and management. This paper discusses the interim results of a continuing research on new strategies for waste management in office building retrofit projects. Firstly based on the literature review, it summarizes the unique characteristics of office building retrofit projects and their influence on waste management. An assumption on waste management strategies is formed. Semi-structured interviews were conducted towards industry practitioners and findings are then presented in the paper. The assumption of the research was validated in the interviews from the opinions and experiences of the respondents. Finally the research develops a process model for waste management in office building retrofit projects. It introduces two different waste management strategies. For the dismantling phase, waste is generated fast along with the work progress, so integrated planning for project delivery and waste generation is needed in order to organize prompt handling and treatment. For the fit-out phase, the work is similar as new construction. Factors which are particularly linked to generating waste on site need to be controlled and monitored. Continuing research in this space will help improve the practice of waste management in office building retrofit projects. The new strategies will help promote the practicality of project waste planning and management and stakeholders’ capability of coordinating waste management and project delivery.

A hierarchical evolutionary algorithmic design (HEAD) system for generating and evolving building design models

This thesis develops a detailed conceptual design method and a system software architecture defined with a parametric and generative evolutionary design system to support an integrated interdisciplinary building design approach. The research recognises the need to shift design efforts toward the earliest phases of the design process to support crucial design decisions that have a substantial cost implication on the overall project budget. The overall motivation of the research is to improve the quality of designs produced at the author's employer, the General Directorate of Major Works (GDMW) of the Saudi Arabian Armed Forces. GDMW produces many buildings that have standard requirements, across a wide range of environmental and social circumstances. A rapid means of customising designs for local circumstances would have significant benefits. The research considers the use of evolutionary genetic algorithms in the design process and the ability to generate and assess a wider range of potential design solutions than a human could manage. This wider ranging assessment, during the early stages of the design process, means that the generated solutions will be more appropriate for the defined design problem. The research work proposes a design method and system that promotes a collaborative relationship between human creativity and the computer capability. The tectonic design approach is adopted as a process oriented design that values the process of design as much as the product. The aim is to connect the evolutionary systems to performance assessment applications, which are used as prioritised fitness functions. This will produce design solutions that respond to their environmental and function requirements. This integrated, interdisciplinary approach to design will produce solutions through a design process that considers and balances the requirements of all aspects of the design. Since this thesis covers a wide area of research material, 'methodological pluralism' approach was used, incorporating both prescriptive and descriptive research methods. Multiple models of research were combined and the overall research was undertaken following three main stages, conceptualisation, developmental and evaluation. The first two stages lay the foundations for the specification of the proposed system where key aspects of the system that have not previously been proven in the literature, were implemented to test the feasibility of the system. As a result of combining the existing knowledge in the area with the newlyverified key aspects of the proposed system, this research can form the base for a future software development project. The evaluation stage, which includes building the prototype system to test and evaluate the system performance based on the criteria defined in the earlier stage, is not within the scope this thesis. The research results in a conceptual design method and a proposed system software architecture. The proposed system is called the 'Hierarchical Evolutionary Algorithmic Design (HEAD) System'. The HEAD system has shown to be feasible through the initial illustrative paper-based simulation. The HEAD system consists of the two main components - 'Design Schema' and the 'Synthesis Algorithms'. The HEAD system reflects the major research contribution in the way it is conceptualised, while secondary contributions are achieved within the system components. The design schema provides constraints on the generation of designs, thus enabling the designer to create a wide range of potential designs that can then be analysed for desirable characteristics. The design schema supports the digital representation of the human creativity of designers into a dynamic design framework that can be encoded and then executed through the use of evolutionary genetic algorithms. The design schema incorporates 2D and 3D geometry and graph theory for space layout planning and building formation using the Lowest Common Design Denominator (LCDD) of a parameterised 2D module and a 3D structural module. This provides a bridge between the standard adjacency requirements and the evolutionary system. The use of graphs as an input to the evolutionary algorithm supports the introduction of constraints in a way that is not supported by standard evolutionary techniques. The process of design synthesis is guided as a higher level description of the building that supports geometrical constraints. The Synthesis Algorithms component analyses designs at four levels, 'Room', 'Layout', 'Building' and 'Optimisation'. At each level multiple fitness functions are embedded into the genetic algorithm to target the specific requirements of the relevant decomposed part of the design problem. Decomposing the design problem to allow for the design requirements of each level to be dealt with separately and then reassembling them in a bottom up approach reduces the generation of non-viable solutions through constraining the options available at the next higher level. The iterative approach, in exploring the range of design solutions through modification of the design schema as the understanding of the design problem improves, assists in identifying conflicts in the design requirements. Additionally, the hierarchical set-up allows the embedding of multiple fitness functions into the genetic algorithm, each relevant to a specific level. This supports an integrated multi-level, multi-disciplinary approach. The HEAD system promotes a collaborative relationship between human creativity and the computer capability. The design schema component, as the input to the procedural algorithms, enables the encoding of certain aspects of the designer's subjective creativity. By focusing on finding solutions for the relevant sub-problems at the appropriate levels of detail, the hierarchical nature of the system assist in the design decision-making process.

Human activity-induced vibration in slender structural systems

Human activity-induced vibrations in slender structural sys tems become apparent in many different excitation modes and consequent action effects that cause discomfort to occupants, crowd panic and damage to public infrastructure. Resulting loss of public confidence in safety of structures, economic losses, cost of retrofit and repairs can be significant. Advanced computational and visualisation techniques enable engineers and architects to evolve bold and innovative structural forms, very often without precedence. New composite and hybrid materials that are making their presence in structural systems lack historical evidence of satisfactory performance over anticipated design life. These structural systems are susceptible to multi-modal and coupled excitation that are very complex and have inadequate design guidance in the present codes and good practice guides. Many incidents of amplified resonant response have been reported in buildings, footbridges, stadia a nd other crowded structures with adverse consequences. As a result, attenuation of human-induced vibration of innovative and slender structural systems very ofte n requires special studies during the design process. Dynamic activities possess variable characteristics and thereby induce complex responses in structures that are sensitive to parametric variations. Rigorous analytical techniques are available for investigation of such complex actions and responses to produce acceptable performance in structural systems. This paper presents an overview and a critique of existing code provisions for human-induced vibration followed by studies on the performance of three contrasting structural systems that exhibit complex vibration. The dynamic responses of these systems under human-induced vibrations have been carried out using experimentally validated computer simulation techniques. The outcomes of these studies will have engineering applications for safe and sustainable structures and a basis for developing design guidance.

Flexible airport terminal design : towards a framework

Flexibility is a key driver of any successful design, specifically in highly unpredictable environment such as airport terminal. Ever growing aviation industry requires airport terminals to be planned and constructed in such a way that will allow flexibility for future design, alteration and redevelopment. The concept of flexibility in terminal design is a relatively new initiative, where existing rules or guidelines are not adequate to assist designers. A shift towards flexible design concept would allow terminal buildings to be designed to accommodate future changes and to make passengers’ journey as simple, timely and hassle free as possible. Currently available research indicates that a theoretical framework on flexible design approach for airport terminals would facilitate the future design process. The generic principles of flexibility are investigated in the current research to incorporate flexible design approaches within the process of an airport terminal design. A conceptual framework is proposed herein, which is expected to ascertain flexibility to current passenger terminal facilities within their corresponding locations as well as in future design and expansion.

Towards local cultures of sustainability : facilitating community created environment education centres through design

Ecological sustainability has been proposed to address the problem of human impacts increasingly degrading planetary resources and ecosystems, threatening biodiversity, eco-services and human survival. Ecological sustainability is an imperative, with Australia having one of the highest eco-footprints per person worldwide. While significant progress has been made via implementation of ecologically sustainable design in urban communities, relatively little has been undertaken in small, disparate regional communities in Australia. Regional communities are disadvantaged by rural economic decline associated with structural change and inequities of resource transfer. The ecologically sustainable solution is holistic, so all settlements need to be globally wise, richly biodiverse yet locally specific. As a regional solution to this global problem, this research offers the practical means by which a small regional community can contribute. It focuses on the design and implementation of a community centre and the fostering of transformative community learning through an integrated ‘learning community’ awareness of ecologically sustainable best practice. Lessons learned are documented by the participant researcher who as a designer, facilitator, local resident and social narrator has been deeply connected with the Tweed-Caldera region over a period since 1980. The collective action of the local community of Chillingham has been diligently recorded over a decade of design and development. Over this period, several positive elements emerged in terms of improvements to the natural and built environment, greater social cohesion and co-operative learning along with a shift towards a greener local economy. Behavioural changes in the community were noted as residents strived to embrace ecological ideals and reduce fossil fuel dependency. They found attractive local solutions to sourcing of food and using local employment opportunities to up skill their residents via transformative learning as a community in transition. Finally, the catalytic impact of external partnering has also been documented. How well the region as a whole has achieved its ecologically sustainable objectives is measured in terms of the delivered success of private and public partnering with the community, the creation of a community centre cum environment education centre, the restoration of local heritage buildings, the repair of riparian forests and improved water conditions in local river systems, better roads and road safety, local skills and knowledge transfer, support of local food and local/regional growers markets to attract tourists via the integrated trails network. In aggregate, each and every element contributes to a measure of eco-positive development for the built environment, its social organisation and its economy that has guided the local community to find its own pathway to sustainability. Within the Tweed-Caldera bioregion in northern New South Wales, there has been a lack of strategic planning, ecologically sustainable knowledge and facilities in isolated communities that could support the development of a local sustained green economy, provide a hub for socio-cultural activities and ecology based education. The first challenge in this research was to model a whole systems approach to eco-positive development in Chillingham, NSW, a small community where Nature and humanity know no specific boundary. The net result was the creation of a community environment education centre featuring best-affordable ecological practice and regionally distinctive, educational building form from a disused heritage building (cow bale). This development, implemented over a decade, resonated with the later regional wide programs that were linked in the Caldera region by the common purpose of extending the reach of local and state government assistance to regional NSW in economic transition coupled with sustainability. The lessons learned from these linked projects reveal that subsequent programs have been significantly easier to initiate, manage, develop and deliver results. In particular, pursuing collaborative networks with all levels of government and external private partners has been economically effective. Each community’s uniqueness has been celebrated and through drawing out these distinctions, has highlighted local vision, strategic planning, sense of belonging and connection of people with place. This step has significantly reduced the level of friction between communities that comes from natural competition for the finite pool of funds. Following the pilot Tweed-Caldera study, several other NSW regional communities are now undertaking a Community Economic Transition Program based on the processes, trials and positive experiences witnessed in the Tweed-Caldera region where it has been demonstrated that regional community transition programs can provide an opportunity to plan and implement effective long term strategies for sustainability, empowering communities to participate in eco-governance. This thesis includes the design and development of a framework for community created environment education centres to provide an equal access place for community to participate to meet their essential needs locally. An environment centre that facilitates community transition based on easily accessible environmental education, skills and infrastructure is necessary to develop local cultures of sustainability. This research draws upon the literatures of ecologically sustainable development, environmental education and community development in the context of regional community transition towards ‘strong sustainability’. The research approach adapted is best described as a four stage collaborative action research cycle where the participant researcher (me) has a significant involvement in the process to foster local cultures of sustainability by empowering its citizens to act locally and in doing so, become more self reliant and socially resilient. This research also draws upon the many fine working exemplars, such as the resilience of the Cuban people, the transition town initiative in Totnes, U.K. and the models of Australian Community Gardens, such as CERES (Melbourne) and Northey Street (Brisbane). The objectives of this study are to research and evaluate exemplars of ecologically sustainable environment education centres, to facilitate the design and development of an environment education centre created by a small regional community as an ecologically sustainable learning environment; to facilitate a framework for community transition based on environmental education, skills and infrastructure necessary to develop local cultures of sustainability. The research was undertaken as action research in the Tweed Caldera in Northern NSW. This involved the author as participant researcher, designer and volunteer in two interconnected initiatives: the Chillingham Community Centre development and the Caldera Economic Transition Program (CETP). Both initiatives involved a series of design-led participatory community workshops that were externally facilitated with the support of government agency partnerships, steering committees and local volunteers. Together the Caldera research programs involved communities participating in developing their own strategic planning process and outcomes. The Chillingham Community Centre was developed as a sustainable community centre/hub using a participatory design process. The Caldera Economic Transition Program (CETP) prioritised Caldera region projects: the Caldera farmer’s market; community gardens and community kitchens; community renewable energy systems and an integrated trails network. The significant findings were: the CETP projects were capable of moving towards an eco-positive design benchmark through transformative learning. Community transition to sustainability programs need to be underpinned by sustainability and environmental education based frameworks and practical on ground experience in local needs based projects through transformative learning. The actioned projects were successfully undertaken through community participation and teamwork. Ecological footprint surveys were undertaken to guide and assess the ongoing community transition process, however the paucity of responses needs to be revisited. The concept of ecologically sustainable development has been adopted internationally, however existing design and planning strategies do not assure future generations continued access to healthy natural life support systems. Sustainable design research has usually been urban focussed, with little attention paid to regional communities. This study seeks to redress this paucity through the design of ecologically sustainable (deep green) learning environments for small regional communities. Through a design-led process of environmental education, this study investigates how regional communities can be facilitated to model the principles of eco-positive development to support transition to local cultures of sustainability. This research shows how community transition processes and projects can incorporate sustainable community development as transformative learning through design. Regional community transition programs can provide an opportunity to plan long term strategies for sustainability, empowering people to participate in eco-governance. A framework is developed for a community created environment education centre to provide an equal access place for the local community to participate in implementing ways to meet their essential needs locally. A community environment education centre that facilitates community transition based on holistic environmental education, skills and infrastructure is necessary to develop local cultures of sustainability.