Ultrasensitive strain sensors made from metal-coated carbon nanofiller/epoxy composites

A set of resistance-type strain sensors has been fabricated from metal-coated carbon nanofiller (CNF)/epoxy composites. Two nanofillers, i.e., multi-walled carbon nanotubes and vapor growth carbon fibers (VGCFs) with nickel, copper and silver coatings were used. The ultrahigh strain sensitivity was observed in these novel sensors as compared to the sensors made from the CNFs without metal-coating, and conventional strain gauges. In terms of gauge factor, the sensor made of VGCFs with silver coating is estimated to be 155, which is around 80 times higher than that in a metal-foil strain gauge. The possible mechanism responsible for the high sensitivity and its dependence with the networks of the CNFs with and without metal-coating and the geometries of the CNFs were thoroughly investigated.

Tensile properties of a boron/nitrogen-doped carbon nanotube–graphene hybrid structure

Doping is an effective approach that allows for the intrinsic modification of the electrical and chemical properties of nanomaterials. Recently, a graphene and carbon nanotube hybrid structure (GNHS) has been reported, which extends the excellent properties of carbon-based materials to three dimensions. In this paper, we carried out a first-time investigation on the tensile properties of the hybrid structures with different dopants. It is found that with the presence of dopants, the hybrid structures usually exhibit lower yield strength, Young’s modulus, and earlier yielding compared to that of a pristine hybrid structure. For dopant concentrations below 2.5% no significant reduction of Young’s modulus or yield strength could be observed. For all considered samples, the failure is found to initiate at the region where the nanotubes and graphene sheets are connected. After failure, monatomic chains are normally observed around the failure region. Dangling graphene layers without the separation of a residual CNT wall are found to adhere to each other after failure with a distance of about 3.4 Å. This study provides a fundamental understanding of the tensile properties of the doped graphene–nanotube hybrid structures, which will benefit the design and also the applications of graphene-based hybrid materials.

A protocol for a pragmatic randomized controlled trial evaluating outcomes of emergency nurse practitioner service

Aim To evaluate emergency nurse practitioner service effectiveness on outcomes related to quality of care and service responsiveness. Background Increasing service pressures in the emergency setting have resulted in the adoption of service innovation models; the most common and rapidly expanding of these is the emergency nurse practitioner. The delivery of high quality patient care in the emergency department is one of the most important service indicators to be measured in health services today. The rapid uptake of emergency nurse practitioner service in Australia has outpaced the capacity to evaluate this model in outcomes related to safety and quality of patient care. Design Pragmatic randomized controlled trial at one site with 260 participants. Methods This protocol describes a definitive prospective randomized controlled trial, which will examine the impact of emergency nurse practitioner service on key patient care and service indicators. The study control will be standard emergency department care. The intervention will be emergency nurse practitioner service. The primary outcome measure is pain score reduction and time to analgesia. Secondary outcome measures are waiting time, number of patients who did not wait, length of stay in the emergency department and representations within 48 hours. Discussion Scant research enquiry evaluating emergency nurse practitioner service on patient effectiveness and service responsiveness exists currently. This study is a unique trial that will test the effectiveness of the emergency nurse practitioner service on patients who present to the emergency department with pain. The research will provide an opportunity to further evaluate emergency nurse practitioner models of care and build research capacity into the workforce.

Measuring the biases in self-reported disability status : Evidence from aggregate data

Self-reported health status measures are generally used to analyse Social Security Disability Insurance's (SSDI) application and award decisions as well as the relationship between its generosity and labour force participation. Due to endogeneity and measurement error, the use of self-reported health and disability indicators as explanatory variables in economic models is problematic. We employ county-level aggregate data, instrumental variables and spatial econometric techniques to analyse the determinants of variation in SSDI rates and explicitly account for the endogeneity and measurement error of the self-reported disability measure. Two surprising results are found. First, it is shown that measurement error is the dominating source of the bias and that the main source of measurement error is sampling error. Second, results suggest that there may be synergies for applying for SSDI when the disabled population is larger. © 2011 Taylor & Francis.

The Queensland Indigenous alcohol diversion program : a health agency’s journey

Drug and alcohol diversion programs provide offenders with the opportunity to divert from the criminal justice or child safety systems, and enter into treatment to address their illicit drug or alcohol use. However, low participation by Indigenous Australians in diversion programs has been recognised as an issue, with Indigenous Australians being much less likely to be diverted into treatment (NIDAC 2009: 9). QIADP represents a unique opportunity to improve Indigenous access to diversion programs. QIADP is an Indigenous-specific alcohol diversion program in its final, third year as a pilot, with the evaluation due December 2009. Many lessons have been learnt by Queensland Health as to what works and doesn’t work in the provision of alcohol-related treatment with this population, including how partnerships with other governmental departments and NGOs can enhance the quality of treatment and ways to build clinical cultural competence in the workforce and programmatic system. This presentation shares the practical lessons QH has learnt in delivering alcohol treatment within an Indigenous-specific diversion program. This includes solutions that others may find useful for application elsewhere, such as the holistic range of treatment options found helpful, and the relationship issues to work through to support a partnership response.

Ethics in project management : some Aristotelian insights

Purpose My aim is to introduce, in the project management field, an Aristotelian ethics lens moving beyond the classical deontological and consequentialism approaches underlying the current ethical practices and codes of ethics and professional conducts. In doing so, I wish to pose the premises of a debate on the implications of a conscious ethical perspective for the structure and agency relationship within the project management field Design/methodology/approach Project management is a knowledge field on its own right. However the current perspectives applied to make sense and develop the field (modernism vs. postmodernism) leads to dichotomous thinking rather than recognizing the merits and contextual validity of both sides. I call for Aristotelian Ethics as a way of moving beyond this dichotomous thinking. I introduce briefly Aristotelian Ethics and its consequences in term of relation theory – practice, means and ends, facts and values, and finally politics (i.e. being part of a community of practitioners). Then I illustrate some consequences for the field taking PMI Code of Ethics and Professional Conduct and APM Code of Professional Conduct as supports for discussion Findings I suggest a need for revisiting and/or redesigning the codes of ethics and professional conducts for project management according to an Aristotelian perspective, in order to move beyond the normative limitations of classical deontological (conflict between competing duties, exemplified by PMI Code) or consequentialism (focusing on the "right" outcome to the detriment of duties, exemplified by APM Code) approaches (both, in fact, leading to a disconnection means and ends, and facts and values). This implicates shifting our view from the question "what is my duty?" to the questions "why should I undertake my duty?" and "how ought I act in this situation?" Practical implications Raising Professional Bodies, Industry and Education institutions awareness and consciousness and leading them to rethink about codes of ethics and the implications for the way they conceive practice and research, bodies of knowledge, credentialing, education... Originality/value To the best of my knowledge, this kind of discussion has not yet been conducted within the project management field, and considering the implication of project management in our life and for the well being of the society, an ethical debate may present some value(s)

Preparation of graphene oxide/epoxy nanocomposites with significantly improved mechanical properties

The effect of graphene oxide (GO) on the mechanical properties and the curing reaction of Diglycidyl Ether of Bisphenol A/F and Triethylenetetramine epoxy system was investigated. GO was prepared by oxidation of graphite flakes and characterized by spectroscopic and microscopic techniques. Epoxy nanocomposites were fabricated with different GO loading by solution mixing technique. It was found that incorporation of small amount of GO into the epoxy matrix significantly enhanced the mechanical properties of the epoxy. In particular, model I fracture toughness was increased by nearly 50% with the addition of 0.1 wt. % GO to epoxy. The toughening mechanism was understood by fractography analysis of the tested samples. The more irregular, coarse, and multi-plane fracture surfaces of the epoxy/GO nanocomposites were observed. This implies that the two-dimensional GO sheets effectively disturbed and deflected the crack propagation. At 0.5 wt. % GO, elastic modulus was ~35% greater than neat epoxy. Differential scanning calorimetry (DSC) results showed that GO addition moderately affect the glass transition temperature (Tg) of epoxy. The maximum decrease of Tg by ~7 oC was shown for the nanocomposite with 0.5 wt. % GO. DSC results further revealed that GO significantly hindered the cure reaction in the epoxy system.

Improvement of the mode II interface fracture toughness of glass fiber reinforced plastics/aluminum laminates through vapor grown carbon fiber interleaves

The effects of acid treatment, vapor grown carbon fiber (VGCF) interlayer and the angle, i.e., 0° and 90°, between the rolling stripes of an aluminum (Al) plate and the fiber direction of glass fiber reinforced plastics (GFRP) on the mode II interlaminar mechanical properties of GFRP/Al laminates were investigated. The experimental results of an end notched flexure test demonstrate that the acid treatment and the proper addition of VGCF can effectively improve the critical load and mode II fracture toughness of GFRP/Al laminates. The specimens with acid treatment and 10 g m−2 VGCF addition possess the highest mode II fracture toughness, i.e., 269% and 385% increases in the 0° and 90° specimens, respectively compared to those corresponding pristine ones. Due to the induced anisotropy by the rolling stripes on the aluminum plate, the 90° specimens possess 15.3%–73.6% higher mode II fracture toughness compared to the 0° specimens. The improvement mechanisms were explored by the observation of crack propagation path and fracture surface with optical, laser scanning and scanning electron microscopies. Moreover, finite element analyses were carried out based on the cohesive zone model to verify the experimental fracture toughness and to predict the interface shear strength between the aluminum plates and GFRP laminates.

Improved energy harvesting capability of poly(vinylidene fluoride) films modified by reduced graphene oxide

Piezoelectric energy harvesters can be used to convert ambient energy into electrical energy and power small autonomous devices. In recent years, massive effort has been made to improve the energy harvesting ability in piezoelectric materials. In this study, reduced graphene oxide was added into poly(vinylidene fluoride) to fabricate the piezoelectric nanocomposite films. Open-circuit voltage and electrical power harvesting experiments showed remarkable enhancement in the piezoelectricity of the fabricated poly(vinylidene fluoride)/reduced graphene oxide nanocomposite, especially at an optimal reduced graphene oxide content of 0.05 wt%. Compared to pristine poly(vinylidene fluoride) films, the open-circuit voltage, the density of harvested power of alternating current, and direct current of the poly(vinylidene fluoride)/reduced graphene oxide nanocomposite films increased by 105%, 153%, and 233%, respectively, indicating a great potential for a broad range of applications.

Prediction of thermal expansion properties of carbon nanotubes using molecular dynamics simulations

The axial coefficients of thermal expansion (CTE) of various carbon nanotubes (CNTs), i.e., single-wall carbon nanotubes (SWCNTs), and some multi-wall carbon nanotubes (MWCNTs), were predicted using molecular dynamics (MDs) simulations. The effects of two parameters, i.e., temperature and the CNT diameter, on CTE were investigated extensively. For all SWCNTs and MWCNTs, the obtained results clearly revealed that within a wide low temperature range, their axial CTEs are negative. As the diameter of CNTs decreases, this temperature range for negative axial CTEs becomes narrow, and positive axial CTEs appear in high temperature range. It was found that the axial CTEs vary nonlinearly with the temperature, however, they decrease linearly as the CNT diameter increases. Moreover, within a wide temperature range, a set of empirical formulations was proposed for evaluating the axial CTEs of armchair and zigzag SWCNTs using the above two parameters. Finally, it was found that the absolute value of the negative axial CTE of any MWCNT is much smaller than those of its constituent SWCNTs, and the average value of the CTEs of its constituent SWCNTs. The present fundamental study is very important for understanding the thermal behaviors of CNTs in such as nanocomposite temperature sensors, or nanoelectronics devices using CNTs.

Does an environmental Kuznets curve for waste pollution exist in China?

China is an emerging and leading world economy. The pace of economic change has been tremendously rapid since the beginning of economic reforms. Despite the importance of the Environmental Kuznets Curve (EKC) and environmental problems in China, no previous study has tested the EKC in China because of the difficulty in obtaining data and the need to adjust the data. The focus of this paper is to test the EKC in China using province level data over the period 1992-2003. This study applies non-parametric techniques to estimate the relationship between income and the environmental quality of wastewater, air pollution and solid waste. Copyright © 2009 Inderscience Enterprises Ltd.

Enhanced interfacial thermal transport across graphene–polymer interfaces by grafting polymer chains

Thermal transport in graphene-polymer nanocomposite is complicated and has not been well understood. The interfacial thermal transport between graphene nanofiller and polymer matrix is expected to play a key role in controlling the overall thermal performance of graphene-polymer nanocomposite. In this work, we investigated the thermal transport across graphene-polymer interfaces functionalized with end-grafted polymer chains using molecular dynamics simulations. The effects of grafting density, chain length and initial morphology on the interfacial thermal transport were systematically investigated. It was found that end-grafted polymer chains could significantly enhance interfacial thermal transport and the underlying mechanism was considered to be the enhanced vibration coupling between graphene and polymer. In addition, a theoretical model based on effective medium theory was established to predict the thermal conductivity in graphene-polymer nanocomposites.

Dancing as Knowledge Production/Dancer as Researcher in Practice-led Research

This chapter discusses research undertaken for a PhD in dance, highlighting the oscillating and ambivalent nature of practice-led research methods. Holding an unusual position within the field of practice-led research in dance, the researcher adopted the role of dancer within four creative processes led by four choreographers. Although instigating and leading this research, the author produced new knowledge of dancing practices whilst being directed creatively by the choreographers in the research environment. In line with many definitions of practice-led research, the methods used were emergent from the research arena and responsive to the requirements of the project. Deeply imbricated in the research environment, the researcher used her embodied self as a research tool, as the one who participated, discovered and recorded. This outsider/insider role of researcher/participant produced a series of meta-positions, leading to a mixed-modal outcome that encompassed live performance, a movement treatise and a written thesis.

Interlaminar mechanical properties of carbon fiber reinforced plastic laminates modified with graphene oxide interleaf

By taking the advantage of the excellent mechanical properties and high specific surface area of graphene oxide (GO) sheets, we develop a simple and effective strategy to improve the interlaminar mechanical properties of carbon fiber reinforced plastic (CFRP) laminates. With the incorporation of graphene oxide reinforced epoxy interleaf into the interface of CFRP laminates, the Mode-I fracture toughness and resistance were greatly increased. The experimental results of double cantilever beam (DCB) tests demonstrated that, with 2 g/m2 addition of GO, the Mode-I fracture toughness and resistance of the specimen increase by 170.8% and 108.0%, respectively, compared to those of the plain specimen. The improvement mechanisms were investigated by the observation of fracture surface with scanning electron microscopies. Moreover, finite element analyses were performed based on the cohesive zone model to verify the experimental fracture toughness and to predict the interfacial tensile strength of CFRP laminates.

Multifunctional SA-PProDOT binder for lithium ion batteries

An environmentally benign, highly conductive, and mechanically strong binder system can overcome the dilemma of low conductivity and insufficient mechanical stability of the electrodes to achieve high performance lithium ion batteries (LIBs) at a low cost and in a sustainable way. In this work, the naturally occurring binder sodium alginate (SA) is functionalized with 3,4-propylenedioxythiophene-2,5-dicarboxylic acid (ProDOT) via a one-step esterification reaction in a cyclohexane/dodecyl benzenesulfonic acid (DBSA)/water microemulsion system, resulting in a multifunctional polymer binder, that is, SA-PProDOT. With the synergetic effects of the functional groups (e.g., carboxyl, hydroxyl, and ester groups), the resultant SA-PProDOT polymer not only maintains the outstanding binding capabilities of sodium alginate but also enhances the mechanical integrity and lithium ion diffusion coefficient in the LiFePO4 (LFP) electrode during the operation of the batteries. Because of the conjugated network of the PProDOT and the lithium doping under the battery environment, the SA-PProDOT becomes conductive and matches the conductivity needed for LiFePO4 LIBs. Without the need of conductive additives such as carbon black, the resultant batteries have achieved the theoretical specific capacity of LiFePO4 cathode (ca. 170 mAh/g) at C/10 and ca. 120 mAh/g at 1C for more than 400 cycles.