Nanoparticle emissions from a fleet of CNG buses in transient and steady state operation

Particle emission measurements from a fleet of 14 CNG and 5 Diesel buses were measured both for transient and steady state mode s on a chassis dynamometer with a CVS dilution system. Several transient DT80 cycles and 4 steady sate modes (0, 25, 50 100% of maximum load) were measured for each bus tested. Particle number concentration data was collected by three CPC’s (TSI 3022, 3010 3782WCPC) having D50 cut-offs set to 5, 10 and 20nm respectively. The size distributions were measured with a TSI 3080 SMPS with a 3025 CPC during the steady state modes. Particle mass emissions were measured with a TSI Dustrak. Particle mass emissions for Diesel buses were upto 2 orders of magnitude higher than for CNG buses. Particle number emissions during steady state modes for Diesel busses were 2 to 5 times higher than for CNG busses for all of the tested loads. On the other hand for the DT80 transient cycle particle number emissions were up to 3 times higher for the CNG buses. More detailed analysis of the transient cycles revealed that the reason for this was due to high particle number emissions from CNG busses during the acceleration parts of the cycles. Particles emitted by the CNG busses during acceleration were in the nucleation mode with the majority being smaller than 10nm. Volatility measurements have also shown that they were highly volatile.

Steady state and transient dynamometer vehicle emission measurements using a DiSC

Analysis of the particulate size and number concentration emissions from a fleet of inner city medium duty CNG buses was conducted using the newly available Diffusion Size Classifier in comparison with more traditional SMPS's and CPC's. Studies were conducted at both steady state and transient driving modes on a vehicle dynamometer utilising a CVS dilution system. Comparative analysis of the results showed that the DiSC provided equivalent information during steady state conditions and was able to provide additional information during transient conditions, namely, the modal diameter of the particle size distribution.

A comparative investigation of C6-C15 hydrocarbons emitted from a passenger car powered by unleaded petrol and 10% ethanol fuel

Twenty-three non-methane hydrocarbons were captured from the exhaust of a car operating on unleaded petrol (ULP) and 10% ethanol fuels at steady speed on a chassis dynamometer. The compounds were identified and quantified by GC/MS/FID and their emission concentrations at 60 km/h, 80km/h and idle speed were evaluated. The most abundant compounds in the exhaust included n-hexane, n-heptane, benzene, toluene, ethyl benzene, m- and p-xylenes, and methylcyclopentane. Because of the large number of compounds involved, no attempt was made to compare the emission concentrations of the compounds. Rather the sum of the emission concentrations for the suite of compounds identified was compared when the car was powered by ULP and 10% ethanol fuel. It was evident from the results that the emission concentrations and factors were generally higher with ULP than with 10% ethanol fuel. The total emission concentrations with the ULP fuel were 2.8, 4.2 and 2.6 times the corresponding values for the 10% ethanol fuel at 60km/h, 80km/h and idle speed, respectively. The implications of the results on the environment are discussed in the paper.

On-road rapid identification of high-polluting transport buses

Exhaust emissions from motor vehicles vary widely and depend on factors such as engine operating conditions, fuel, age, mileage and service history. A method has been devised to rapidly identify high-polluting vehicles as they travel on the road. The method is able to monitor emissions from a large number of vehicles in a short time and avoids the need to conduct expensive and time consuming tests on chassis dynamometers. A sample of the exhaust plume is captured as each vehicle passes a roadside monitoring station and the pollutant emission factors are calculated from the measured concentrations using carbon dioxide as a tracer. Although, similar methods have been used to monitor soot and gaseous mass emissions, to-date it has not been used to monitor particle number emissions from a large fleet of vehicles. This is particularly important as epidemiological studies have shown that particle number concentration is an important parameter in determining adverse health effects. The method was applied to measurements of particle number emissions from individual buses in the Brisbane City Council diesel fleet operating on the South-East Busway. Results indicate that the particle number emission factors are gamma- distributed, with a high proportion of the emissions being emitted by a small percentage of the buses. Although most of the high-emitters are the oldest buses in the fleet, there are clear exceptions, with some newer buses emitting as much. We attribute this to their recent service history, particularly pertaining to improper tuning of the engines. We recommend that a targeted correction program would be a highly effective measure in mitigating urban environmental pollution.

Effect of Oil Price on Emissions Trading Market: VAR Analysis

In this study, we investigated the relationship of European Union carbon dioxide CO2 allowances EUAs prices and oil prices by employing a VAR analysis, Granger causality test and impulse response function. If oil price continues increasing, companies will decrease dependency on fossil fuels because of an increase in energy costs. Therefore, the price of EUAs may be affected by variations in oil prices if the greenhouse gases discharged by the consumption of alternative energy are less than that of fossil fuels. There are no previous studies that investigated these relationships. In this study, we analyzed eight types of EUAs EUA05 to EUA12 with a time series daily data set during 2005-2007 collected from a European Climate Exchange time series data set. Differentiations in these eight types were redemption period. We used the New York Mercantile Exchange light sweet crude price as an oil price. From our examination, we found that only the EUA06 and EUA07 types of EUAs Granger-cause oil prices and vice versa and other six types of EUAs do not Granger-cause oil price. These results imply that the earlier redemption period types of EUAs are more sensitive to oil price. In employing the impulse response function, the results showed that a shock to oil price has a slightly positive effect on all types of EUAs for a very short period. On the other hand, we found that a shock to price of EUA has a slightly negative effect on oil price following a positive effect in only EUA06 and EUA07 types. Therefore, these results imply that fluctuations in EUAs prices and oil prices have little effect on each other. Lastly, we did not consider the substitute energy prices in this study, so we plan to include the prices of coal and natural gas in future analyses.

Case study analysis for the development and implementation of sustainable housing in the kingdom of Saudi Arabia

Rapid urbanization in developing countries is putting stress on current infrastructure, which is resulting in the rapid consumption of natural resources to cope with the increasing demand of the population. Saudi Arabia is one of the developing countries facing rapid urbanization where its infrastructure is facing a huge demand by the increasing urbanization levels of its major cities. Developing sustainable housing in Saudi Arabia is a must for the preservation of resources for future generations of the region and of the world. In the coming years, several resources (such as fossil fuels and natural water) will be facing shortage if not managed properly. Providing electricity for housing in Saudi Arabia is one of the biggest challenges facing the country, where it is estimated that by 2050 energy demand in the Kingdom will be approximately 120 GW, and to meet this growing demand, 8 million barrels of oil per day will be required. However, implementation of Sustainable Housing in Saudi is still problematic to reach the desired goals of various key Saudi stakeholders. This paper analyses three case studies that have adopted sustainable construction methods and compares them to traditional non-sustainable houses. The outcome suggests that there is a viable chance for development of sustainable housing in the region if supported by the government with less red tape to deal with. This paper recommends that the Saudi governments should mandate new laws to reduce the overall consumption of energy and water to reduce the overall consumption of natural resources to secure the future generation’s demand of natural resources.

Effect of temperature and moisture on high pressure lipid/oil extraction from microalgae

Commercially viable carbon–neutral biodiesel production from microalgae has potential for replacing depleting petroleum diesel. The process of biodiesel production from microalgae involves harvesting, drying and extraction of lipids which are energy- and cost-intensive processes. The development of effective large-scale lipid extraction processes which overcome the complexity of microalgae cell structure is considered one of the most vital requirements for commercial production. Thus the aim of this work was to investigate suitable extraction methods with optimised conditions to progress opportunities for sustainable microalgal biodiesel production. In this study, the green microalgal species consortium, Tarong polyculture was used to investigate lipid extraction with hexane (solvent) under high pressure and variable temperature and biomass moisture conditions using an Accelerated Solvent Extraction (ASE) method. The performance of high pressure solvent extraction was examined over a range of different process and sample conditions (dry biomass to water ratios (DBWRs): 100%, 75%, 50% and 25% and temperatures from 70 to 120 ºC, process time 5–15 min). Maximum total lipid yields were achieved at 50% and 75% sample dryness at temperatures of 90–120 ºC. We show that individual fatty acids (Palmitic acid C16:0; Stearic acid C18:0; Oleic acid C18:1; Linolenic acid C18:3) extraction optima are influenced by temperature and sample dryness, consequently affecting microalgal biodiesel quality parameters. Higher heating values and kinematic viscosity were compliant with biodiesel quality standards under all extraction conditions used. Our results indicate that biodiesel quality can be positively manipulated by selecting process extraction conditions that favour extraction of saturated and mono-unsaturated fatty acids over optimal extraction conditions for polyunsaturated fatty acids, yielding positive effects on cetane number and iodine values. Exceeding biodiesel standards for these two parameters opens blending opportunities with biodiesels that fall outside the minimal cetane and maximal iodine values.

Aggregating energy supply and demand

Energy usage in general, and electricity usage in particular, are major concerns internationally due to the increased cost of providing energy supplies and the environmental impacts of electricity generation using carbon-based fuels. If a "systems" approach is taken to understanding energy issues then both supply and demand need to be considered holistically. This paper examines two research projects in the energy area with IT tools as key deliverables, one examining supply issues and the other studying demand side issues. The supply side project used hard engineering methods to build the models and software, while the demand side project used a social science approach. While the projects are distinct, there was an overlap in personnel. Comparing the knowledge extraction, model building, implementation and interface issues of these two deliverables identifies both interesting contrasts and commonalities.

Combustion analysis of microalgae methyl ester in a common rail direct injection diesel engine

In this study, the biodiesel properties and effects of blends of oil methyl ester petroleum diesel on a CI direct injection diesel engine is investigated. Blends were obtained from the marine dinoflagellate Crypthecodinium cohnii and waste cooking oil. The experiment was conducted using a four-cylinder, turbo-charged common rail direct injection diesel engine at four loads (25%, 50%, 75% and 100%). Three blends (10%, 20% and 50%) of microalgae oil methyl ester and a 20% blend of waste cooking oil methyl ester were compared to petroleum diesel. To establish suitability of the fuels for a CI engine, the effects of the three microalgae fuel blends at different engine loads were assessed by measuring engine performance, i.e. mean effective pressure (IMEP), brake mean effective pressure (BMEP), in cylinder pressure, maximum pressure rise rate, brake-specific fuel consumption (BSFC), brake thermal efficiency (BTE), heat release rate and gaseous emissions (NO, NOx,and unburned hydrocarbons (UHC)). Results were then compared to engine performance characteristics for operation with a 20% waste cooking oil/petroleum diesel blend and petroleum diesel. In addition, physical and chemical properties of the fuels were measured. Use of microalgae methyl ester reduced the instantaneous cylinder pressure and engine output torque, when compared to that of petroleum diesel, by a maximum of 4.5% at 50% blend at full throttle. The lower calorific value of the microalgae oil methyl ester blends increased the BSFC, which ultimately reduced the BTE by up to 4% at higher loads. Minor reductions of IMEP and BMEP were recorded for both the microalgae and the waste cooking oil methyl ester blends at low loads, with a maximum of 7% reduction at 75% load compared to petroleum diesel. Furthermore, compared to petroleum diesel, gaseous emissions of NO and NOx, increased for operations with biodiesel blends. At full load, NO and NOx emissions increased by 22% when 50% microalgae blends were used. Petroleum diesel and a 20% blend of waste cooking oil methyl ester had emissions of UHC that were similar, but those of microalgae oil methyl ester/petroleum diesel blends were reduced by at least 50% for all blends and engine conditions. The tested microalgae methyl esters contain some long-chain, polyunsaturated fatty acid methyl esters (FAMEs) (C22:5 and C22:6) not commonly found in terrestrial-crop-derived biodiesels yet all fuel properties were satisfied or were very close to the ASTM 6751-12 and EN14214 standards. Therefore, Crypthecodinium cohnii- derived microalgae biodiesel/petroleum blends of up to 50% are projected to meet all fuel property standards and, engine performance and emission results from this study clearly show its suitability for regular use in diesel engines.

Predictors of chronic bronchitis in South African adults

SETTING National household survey of adults in South Africa, a middle income country. OBJECTIVE To determine the prevalence and predictors of chronic bronchitis. DESIGN A stratified national probability sample of households was selected. All adults in the selected households were interviewed. Chronic bronchitis was defined as chronic productive cough. Socio-demographic predictors were wealth, education, race, age and urban residence. Personal and exposure variables included history of tuberculosis, domestic exposure to smoky fuels, occupational exposures, smoking and body mass index. RESULTS The overall prevalence of chronic bronchitis was 2.3% in men and 2.8% in women. The strongest predictor of chronic bronchitis was a history of tuberculosis (men, odds ratio [OR] 4.9; 95% confidence interval [CI] 2.6-9.2; women, OR 6.6; 95% CI 3.7-11.9). Other risk factors were smoking, occupational exposure (in men), domestic exposure to smoky fuel (in women) and (in univariate analysis only) being underweight. Wealth and particularly education were protective. CONCLUSION The pattern of chronic bronchitis in South Africa suggests a combination of risk factors that includes not only smoking but also tuberculosis, occupational exposures in men and domestic fuel exposure in women. Control of these risk factors requires public health action across a broad front. The protective role of education requires elucidation.

Wheeze, asthma diagnosis and medication use : a national adult survey in a developing country

Background As relatively little is known about adult wheeze and asthma in developing countries, this study aimed to determine the predictors of wheeze, asthma diagnosis, and current treatment in a national survey of South African adults. Methods A stratified national probability sample of households was drawn and all adults (>14 years) in the selected households were interviewed. Outcomes of interest were recent wheeze, asthma diagnosis, and current use of asthma medication. Predictors of interest were sex, age, household asset index, education, racial group, urban residence, medical insurance, domestic exposure to smoky fuels, occupational exposure, smoking, body mass index, and past tuberculosis. Results A total of 5671 men and 8155 women were studied. Although recent wheeze was reported by 14.4% of men and 17.6% of women and asthma diagnosis by 3.7% of men and 3.8% of women, women were less likely than men to be on current treatment (OR 0.6; 95% confidence interval (CI) 0.5 to 0.8). A history of tuberculosis was an independent predictor of both recent wheeze (OR 3.4; 95% CI 2.5 to 4.7) and asthma diagnosis (OR 2.2; 95% CI 1.5 to 3.2), as was occupational exposure (wheeze: OR 1.8; 95% CI 1.5 to 2.0; asthma diagnosis: OR 1.9; 95% CI 1.4 to 2.4). Smoking was associated with wheeze but not asthma diagnosis. Obesity showed an association with wheeze only in younger women. Both wheeze and asthma diagnosis were more prevalent in those with less education but had no association with the asset index. Independently, having medical insurance was associated with a higher prevalence of diagnosis. Conclusions Some of the findings may be to due to reporting bias and heterogeneity of the categories wheeze and asthma diagnosis, which may overlap with post tuberculous airways obstruction and chronic obstructive pulmonary disease due to smoking and occupational exposures. The results underline the importance of controlling tuberculosis and occupational exposures as well as smoking in reducing chronic respiratory morbidity. Validation of the asthma questionnaire in this setting and research into the pathophysiology of post tuberculous airways obstruction are also needed.

Estimating the burden of disease attributable to four selected environmental risk factors in South Africa

INTRODUCTION: The first South African National Burden of Disease study quantified the underlying causes of premature mortality and morbidity experienced in South Africa in the year 2000. This was followed by a Comparative Risk Assessment to estimate the contributions of 17 selected risk factors to burden of disease in South Africa. This paper describes the health impact of exposure to four selected environmental risk factors: unsafe water, sanitation and hygiene; indoor air pollution from household use of solid fuels; urban outdoor air pollution and lead exposure. METHODS: The study followed World Health Organization comparative risk assessment methodology. Population-attributable fractions were calculated and applied to revised burden of disease estimates (deaths and disability adjusted life years, [DALYs]) from the South African Burden of Disease study to obtain the attributable burden for each selected risk factor. The burden attributable to the joint effect of the four environmental risk factors was also estimated taking into account competing risks and common pathways. Monte Carlo simulation-modeling techniques were used to quantify sampling, uncertainty. RESULTS: Almost 24 000 deaths were attributable to the joint effect of these four environmental risk factors, accounting for 4.6% (95% uncertainty interval 3.8-5.3%) of all deaths in South Africa in 2000. Overall the burden due to these environmental risks was equivalent to 3.7% (95% uncertainty interval 3.4-4.0%) of the total disease burden for South Africa, with unsafe water sanitation and hygiene the main contributor to joint burden. The joint attributable burden was especially high in children under 5 years of age, accounting for 10.8% of total deaths in this age group and 9.7% of burden of disease. CONCLUSION: This study highlights the public health impact of exposure to environmental risks and the significant burden of preventable disease attributable to exposure to these four major environmental risk factors in South Africa. Evidence-based policies and programs must be developed and implemented to address these risk factors at individual, household, and community levels.

Poverty and non-communicable diseases in South Africa

Background: High levels of wealth inequality with improved health statistics in South Africa (SA) provide an important opportunity to investigate non-communicable diseases (NCDs) among the poor. Aims: This paper uses two distinct national data sets to contrast patterns of mortality in rich and poor areas and explore the associations between poverty, risk factors, health care and selected NCDs diseases in South African adults. Methods: Causes of premature mortality in 1996 experienced in the poorest magisterial districts are compared with those in the richest, using average household wealth to classify districts. Logistic and multinomial regression are used to investigate the association of a household asset index and selected chronic conditions, related risk factors and healthcare indicators using data from the 1998 South African Demographic and Health Survey. Results: NCDs accounted for 39% and 33% of premature mortality in rich and poor districts respectively. The household survey data showed that the risk factors hypertension and obesity increased with increasing wealth, while most of the lifestyle factors, such as light smoking, domestic exposure to ``smoky'' fuels and alcohol dependence were associated with poverty. Treatment status for hypertension and asthma was worse for poor people than for rich people. Conclusions: The study suggests that NCDs and lifestyle-related risk factors are prevalent among the poor in SA and treatment for chronic diseases is lacking for poor people. The observed increase in hypertension and obesity with wealth suggests that unless comprehensive health promotion strategies are implemented, there will be an unmanageable chronic disease epidemic with future socioeconomic development in SA.

Technoeconomic analysis of an integrated microalgae photobioreactor, biodiesel and biogas production facility

As fossil fuel prices increase and environmental concerns gain prominence, the development of alternative fuels from biomass has become more important. Biodiesel produced from microalgae is becoming an attractive alternative to share the role of petroleum. Currently it appears that the production of microalgal biodiesel is not economically viable in current environment because it costs more than conventional fuels. Therefore, a new concept is introduced in this article as an option to reduce the total production cost of microalgal biodiesel. The integration of biodiesel production system with methane production via anaerobic digestion is proved in improving the economics and sustainability of overall biodiesel stages. Anaerobic digestion of microalgae produces methane and further be converted to generate electricity. The generated electricity can surrogate the consumption of energy that require in microalgal cultivation, dewatering, extraction and transesterification process. From theoretical calculations, the electricity generated from methane is able to power all of the biodiesel production stages and will substantially reduce the cost of biodiesel production (33% reduction). The carbon emissions of biodiesel production systems are also reduced by approximately 75% when utilizing biogas electricity compared to when the electricity is otherwise purchased from the Victorian grid. The overall findings from this study indicate that the approach of digesting microalgal waste to produce biogas will make the production of biodiesel from algae more viable by reducing the overall cost of production per unit of biodiesel and hence enable biodiesel to be more competitive with existing fuels.