A numerical method to quantify the axial shortening of vertical elements in concrete buildings

Differential axial shortening, distortion and deformation in high rise buildings is a serious concern. They are caused by three time dependent modes of volume change; “shrinkage”, “creep” and “elastic shortening” that takes place in every concrete element during and after construction. Vertical concrete components in a high rise building are sized and designed based on their strength demand to carry gravity and lateral loads. Therefore, columns and walls are sized, shaped and reinforced differently with varying concrete grades and volume to surface area ratios. These structural components may be subjected to the detrimental effects of differential axial shortening that escalates with increasing the height of buildings. This can have an adverse impact on other structural and non-structural elements. Limited procedures are available to quantify axial shortening, and the results obtained from them differ because each procedure is based on various assumptions and limited to few parameters. All these prompt to a need to develop an accurate numerical procedure to quantify the axial shortening of concrete buildings taking into account the important time varying functions of (i) construction sequence (ii) Young’s Modulus and (iii) creep and shrinkage models associated with reinforced concrete. General assumptions are refined to minimize variability of creep and shrinkage parameters to improve accuracy of the results. Finite element techniques are used in the procedure that employs time history analysis along with compression only elements to simulate staged construction behaviour. This paper presents such a procedure and illustrates it through an example. Keywords: Differential Axial Shortening, Concrete Buildings, Creep and Shrinkage, Construction Sequence, Finite Element Method.

Property Education : an evaluation of how well undergraduate property students are prepared for commencing their careers

The evolution of property education to adapt to the changing business environment requires changes to course content, method of delivery and assessment. Many universities have a special interest in understanding how the students transition in and transition out of the property programs. The impact of the first year student experience is often easier to assess through students’ progression in the course and performance in their intermediate and advanced units. However, the students’ success in transitioning from university student to property professional is often more difficult to determine. In an environment where many property students commence their professional careers while still completing their undergraduate property qualification, a survey of current final year students was undertaken to identify the students’ perception of their level of preparedness for entry into the professional world. This study has also been informed by feedback received from and informal discussions held with industry representative bodies, alumni and senior members of professional organisations. The QUT UD40 Bachelor of Urban Development, Property Economics course has been designed to achieve graduate capabilities in core technical skills and generic professional skills which are required by property professionals. The results of this study were that some units in the program were perceived to provide direct preparation for students commencing their professional careers whilst the impact of other units was less tangible. Valuable feedback received during the study included an assessment of the relevance of many multi-disciplinary units, the appropriateness of the programming of units within the course and the appropriateness of repetition of content during the course. The further research question arises as to how universities can better assist students in the transition to the professional environment when frequently this occurs prior to completion of the property course.

Current rural valuation practice : a survey of valuers and agribusiness managers on farm management and sustainable rural land use

Over the past 20 years the nature of rural valuation practice has required most rural valuers to undertake studies in both agriculture (farm management) and valuation, especially if carrying out valuation work for financial institutions. The additional farm financial and management information obtained by rural valuers exceeds that level of information required to value commercial, retail and industrial by the capitalisation of net rent/profit valuation method and is very similar to the level of information required for the valuation of commercial and retail property by the Discounted Cash Flow valuation method. On this basis the valuers specialising in rural valuation practice have the necessary skills and information to value rural properties by an income valuation method, which can focus on the long term environmental and economic sustainability of the property being valued. This paper will review the results of an extensive survey carried out by rural property valuers in Australia, in relation to the impact of farm management on rural property values and sustainable rural land use. A particular focus of the research relates to the increased awareness of the problems of rural land degradation in Australia and the subsequent impact such problems have on the productivity of rural land. These problems of sustainable land use have resulted in the need to develop an approach to rural valuation practice that allows the valuer to factor the past management practices on the subject rural property into the actual valuation figure. An analysis of the past farm management and the inclusion of this data into the valuation methodology provides a much more reliable indication of farm sustainable economic value than the existing direct comparison valuation methodology.

A method of lines approach for modelling saltwater intrusion in coastal aquifiers

The equations governing saltwater intrusion in coastal aquifers are complex. Backward Euler time stepping approaches are often used to advance the solution to these equations in time, which typically requires that small time steps be taken in order to ensure that an accurate solution is obtained. We show that a method of lines approach incorporating variable order backward differentiation formulas can greatly improve the efficiency of the time stepping process.

Toward a fuzzy domain ontology extraction method for adaptive e-learning

With the widespread applications of electronic learning (e-Learning) technologies to education at all levels, increasing number of online educational resources and messages are generated from the corresponding e-Learning environments. Nevertheless, it is quite difficult, if not totally impossible, for instructors to read through and analyze the online messages to predict the progress of their students on the fly. The main contribution of this paper is the illustration of a novel concept map generation mechanism which is underpinned by a fuzzy domain ontology extraction algorithm. The proposed mechanism can automatically construct concept maps based on the messages posted to online discussion forums. By browsing the concept maps, instructors can quickly identify the progress of their students and adjust the pedagogical sequence on the fly. Our initial experimental results reveal that the accuracy and the quality of the automatically generated concept maps are promising. Our research work opens the door to the development and application of intelligent software tools to enhance e-Learning.

Current rural valuation practice : a survey of NSW valuers and agribusiness managers

Despite the advances that have been made in relation to the valuation of Commercial, Industrial and retail property, there has not been the same progress in relation to the valuation of rural property. Although number of rural property valuations also require the valuer to carry out a full analysis of the economic performance of the farming operations, as well as the long term environmental viability of the farm, this information is rarely used to assess the value of the property, nor is it even used for a secondary valuation method. Over the past 20 years the nature of rural valuation practice has required most rural valuers to undertake studies in both agriculture (farm management) and valuation, especially if carrying out valuation work for financial institutions. The additional farm financial and management information obtained by rural valuers exceeds that level of information required to value commercial, retail and industrial by the capitalisation of net rent/profit valuation method and is very similar to the level of information required for the valuation of commercial and retail property by the Discounted Cash Flow valuation method. On this basis the valuers specialising in rural valuation practice have the necessary skills and information to value rural properties by an income valuation method. Although the direct comparison method of valuation has been sufficient in the past to value rural properties the future use of the method as the main valuation method is limited and valuers need to adopt an income valuation method as at least a secondary valuation method to overcome the problems associated with the use of direct comparison as the only rural property valuation method, especially in view of the impact that farm technical, financial and environmental .management can have on rural property values. This paper will review the results of an extensive survey carried out by rural property valuers and agribusiness managers in NSW, in relation to the impact of farm management on rural property values and rural property valuation practice.

The use of income valuation methods to value rural property

Despite the advances that have been made in relation to the valuation of commercial, industrial and retail property, there has not been the same progress in relation to the valuation of rural property. Although the majority of rural property valuations also require the valuer to carry out a full analysis of the economic performance of the farming operations, this information is rarely used to assess the value of the property, nor is it even used for a secondary valuation method. Over the past 20 years the nature of rural valuation practice has required rural valuers to undertake studies in both agriculture (farm management) and valuation, especially if carrying out valuation work for financial institutions. The additional farm financial information obtained by rural valuers exceeds that level of information required to value commercial, retail and industrial by the capitalisation of net rent/profit valuation method and is very similar to the level of information required for the valuation of commercial and retail property by the Discounted Cash Flow valuation method. On this basis the valuers specialising in rural valuation practice should have the necessary skills and information to value rural properties by an income valuation method. Although the direct comparison method of valuation has been sufficient in the past to value rural properties the future use of the method as the main valuation method is limited and valuers need to adopt an income valuation method as at least a secondary valuation method to overcome the problems associated with the use of direct comparison as the only rural property valuation method. This paper will review the results of an extensive survey carried out by rural property valuers in New South Wales (NSW), Australia, in relation to the impact of farm management on rural property values and rural property income potential.

Moderating drinking by correspondence : an evaluation of a new method of intervention

Recognizing the need to offer alternative methods of brief interventions, this study developed correspondence treatments for low-dependent problem drinkers and evaluated their impact. One hundred and twenty-one problem drinkers were recruited by media advertisements and were randomly allocated to a full cognitive behavioural treatment programme (CBT) or to a minimal intervention condition (MI) that gave information regarding alcohol misuse and instructions to record drinking. As predicted, CBT was more effective than MI in reducing alcohol consumption over the 4-month controlled trial period. CBT produced a 50% fall in consumption, bringing the average intake of subjects within recommended maximum levels. Treatment gains at 6 months were well maintained to 12 months. High levels of consumer satisfaction, a high representation of women and a substantial participation from isolated rural areas attested to the feasibility of the correspondence programme as an alternative treatment. However, some drinking occasions still involved high intake for a significant subgroup of subjects, and this issue will be addressed in future programmes. The results supported the use of correspondence delivery as a means of promoting early engagement and equity of access between city and country areas.

A differential kinetic spectrophotometric method for determination of three sulphanilamide artificial sweeteners with the aid of chemometrics

A simple and sensitive spectrophotometric method for the simultaneous determination of acesulfame-K, sodium cyclamate and saccharin sodium sweeteners in foodstuff samples has been researched and developed. This analytical method relies on the different kinetic rates of the analytes in their oxidative reaction with KMnO4 to produce the green manganate product in an alkaline solution. As the kinetic rates of acesulfame-K, sodium cyclamate and saccharin sodium were similar and their kinetic data seriously overlapped, chemometrics methods, such as partial least squares (PLS), principal component regression (PCR) and classical least squares (CLS), were applied to resolve the kinetic data. The results showed that the PLS prediction model performed somewhat better. The proposed method was then applied for the determination of the three sweeteners in foodstuff samples, and the results compared well with those obtained by the reference HPLC method.

Behaviour and design of cold-formed steel compression members at elevated temperatures

Cold-formed steel members have been widely used in residential, industrial and commercial buildings as primary load bearing structural elements and non-load bearing structural elements (partitions) due to their advantages such as higher strength to weight ratio over the other structural materials such as hot-rolled steel, timber and concrete. Cold-formed steel members are often made from thin steel sheets and hence they are more susceptible to various buckling modes. Generally short columns are susceptible to local or distortional buckling while long columns to flexural or flexural-torsional buckling. Fire safety design of building structures is an essential requirement as fire events can cause loss of property and lives. Therefore it is essential to understand the fire performance of light gauge cold-formed steel structures under fire conditions. The buckling behaviour of cold-formed steel compression members under fire conditions is not well investigated yet and hence there is a lack of knowledge on the fire performance of cold-formed steel compression members. Current cold-formed steel design standards do not provide adequate design guidelines for the fire design of cold-formed steel compression members. Therefore a research project based on extensive experimental and numerical studies was undertaken at the Queensland University of Technology to investigate the buckling behaviour of light gauge cold-formed steel compression members under simulated fire conditions. As the first phase of this research, a detailed review was undertaken on the mechanical properties of light gauge cold-formed steels at elevated temperatures and the most reliable predictive models for mechanical properties and stress-strain models based on detailed experimental investigations were identified. Their accuracy was verified experimentally by carrying out a series of tensile coupon tests at ambient and elevated temperatures. As the second phase of this research, local buckling behaviour was investigated based on the experimental and numerical investigations at ambient and elevated temperatures. First a series of 91 local buckling tests was carried out at ambient and elevated temperatures on lipped and unlipped channels made of G250-0.95, G550-0.95, G250-1.95 and G450-1.90 cold-formed steels. Suitable finite element models were then developed to simulate the experimental conditions. These models were converted to ideal finite element models to undertake detailed parametric study. Finally all the ultimate load capacity results for local buckling were compared with the available design methods based on AS/NZS 4600, BS 5950 Part 5, Eurocode 3 Part 1.2 and the direct strength method (DSM), and suitable recommendations were made for the fire design of cold-formed steel compression members subject to local buckling. As the third phase of this research, flexural-torsional buckling behaviour was investigated experimentally and numerically. Two series of 39 flexural-torsional buckling tests were undertaken at ambient and elevated temperatures. The first series consisted 2800 mm long columns of G550-0.95, G250-1.95 and G450-1.90 cold-formed steel lipped channel columns while the second series contained 1800 mm long lipped channel columns of the same steel thickness and strength grades. All the experimental tests were simulated using a suitable finite element model, and the same model was used in a detailed parametric study following validation. Based on the comparison of results from the experimental and parametric studies with the available design methods, suitable design recommendations were made. This thesis presents a detailed description of the experimental and numerical studies undertaken on the mechanical properties and the local and flexural-torsional bucking behaviour of cold-formed steel compression member at ambient and elevated temperatures. It also describes the currently available ambient temperature design methods and their accuracy when used for fire design with appropriately reduced mechanical properties at elevated temperatures. Available fire design methods are also included and their accuracy in predicting the ultimate load capacity at elevated temperatures was investigated. This research has shown that the current ambient temperature design methods are capable of predicting the local and flexural-torsional buckling capacities of cold-formed steel compression members at elevated temperatures with the use of reduced mechanical properties. However, the elevated temperature design method in Eurocode 3 Part 1.2 is overly conservative and hence unsuitable, particularly in the case of flexural-torsional buckling at elevated temperatures.

A Numerical Solution Using an Adaptively Preconditioned Lanczos Method for a Class of Linear Systems Related with the Fractional Poisson Equation

This study considers the solution of a class of linear systems related with the fractional Poisson equation (FPE) (−∇2)α/2φ=g(x,y) with nonhomogeneous boundary conditions on a bounded domain. A numerical approximation to FPE is derived using a matrix representation of the Laplacian to generate a linear system of equations with its matrix A raised to the fractional power α/2. The solution of the linear system then requires the action of the matrix function f(A)=A−α/2 on a vector b. For large, sparse, and symmetric positive definite matrices, the Lanczos approximation generates f(A)b≈β0Vmf(Tm)e1. This method works well when both the analytic grade of A with respect to b and the residual for the linear system are sufficiently small. Memory constraints often require restarting the Lanczos decomposition; however this is not straightforward in the context of matrix function approximation. In this paper, we use the idea of thick-restart and adaptive preconditioning for solving linear systems to improve convergence of the Lanczos approximation. We give an error bound for the new method and illustrate its role in solving FPE. Numerical results are provided to gauge the performance of the proposed method relative to exact analytic solutions.

A pilot study utilising cross-age peer tutoring as a method of intervention for anxious adolescents

Anxiety disorders are the most common psychopathology experienced by young people, with up to 18% of adolescents developing an anxiety disorder. The consequences of these disorders, if left untreated, include impaired peer relationships, school absenteeism and self-concept problems. In addition, anxiety disorders may play a causal role in the development of depression in young people, precede eating disorders and predispose adolescents to substance abuse disorders. While the school is often chosen as a place to provide early intervention for this debilitating disorder, the fact that excessive anxiety is often not recognised in school and that young people are reluctant to seek help, makes identifying these adolescents difficult. Even when these young people are identified, there are problems in providing sensitive programs which are not stigmatising to them within a school setting. One method which may engage this adolescent population could be cross-age peer tutoring. This paper reports on a small pilot study using the “Worrybusters” program and a cross-age peer tutoring method to engage the anxious adolescents. These anxious secondary school students planned activities for teacher-referred anxious primary school students for a term in the high school setting and then delivered those activities to the younger students weekly in the next term in the primary school. Although the secondary school students decreased their scores on anxiety self-report measures there were no significant differences for primary school students’ self-reports. However, the primary school parent reports indicated a significant decrease in their child’s anxiety.

Practice as method : the ex/centric fixations project

In the past decade, scholars have proposed a range of terms to describe the relationship between practice and research in the creative arts, including increasingly nuanced definitions of practice-based research, practice-led research and practice-as-research. In this paper, I consider the efficacy of creative practice as method. I use the example of The Ex/Centric Fixations Project – a project in which I have embedded creative practice in a research project, rather than embedding research in a creative project. The Ex/Centric Fixations project investigates the way spectators interpret human experiences – especially human experiences of difference, marginalisation or discrimination – depicted onstage. In particular, it investigates the way postmodern performance writing strategies, and the presence of performing bodied to which the experience depicted can be attached, impacts on interpretations. It is part of a broader research project which examines the performativity of spectatorship, and intervenes in emergent debates about performance, ethics and spectatorship in the context of debate about whether live performance is a privileged site for the emergence of an ethical face-to-face encounter with the Other. Using the metaphor of the Mobius strip, I examines the way practice – as a method, rather than an output – has informed, influenced and problematised the broader research project.

Metal oxide nanofibres membranes assembled by spin-coating method

Ceramic membranes are of particular interest in many industrial processes due to their ability to function under extreme conditions while maintaining their chemical and thermal stability. Major structural deficiencies under conventional fabrication approach are pin-holes and cracks, and the dramatic losses of flux when pore sizes are reduced to enhance selectivity. We overcome these structural deficiencies by constructing hierarchically structured separation layer on a porous substrate using larger titanate nanofibres and smaller boehmite nanofibres. This yields a radical change in membrane texture. The differences in the porous supports have no substantial influences on the texture of resulting membranes. The membranes with top layer of nanofibres coated on different porous supports by spin-coating method have similar size of the filtration pores, which is in a range of 10–100 nm. These membranes are able to effectively filter out species larger than 60 nm at flow rates orders of magnitude greater than conventional membranes. The retention can attain more than 95%, while maintaining a high flux rate about 900 L m-2 h. The calcination after spin-coating creates solid linkages between the fibres and between fibres and substrate, in addition to convert boehmite into -alumina nanofibres. This reveals a new direction in membrane fabrication.

Krylov subspace methods for approximating functions of symmetric positive definite matrices with applications to applied statistics and anomalous diffusion

Matrix function approximation is a current focus of worldwide interest and finds application in a variety of areas of applied mathematics and statistics. In this thesis we focus on the approximation of A^(-α/2)b, where A ∈ ℝ^(n×n) is a large, sparse symmetric positive definite matrix and b ∈ ℝ^n is a vector. In particular, we will focus on matrix function techniques for sampling from Gaussian Markov random fields in applied statistics and the solution of fractional-in-space partial differential equations. Gaussian Markov random fields (GMRFs) are multivariate normal random variables characterised by a sparse precision (inverse covariance) matrix. GMRFs are popular models in computational spatial statistics as the sparse structure can be exploited, typically through the use of the sparse Cholesky decomposition, to construct fast sampling methods. It is well known, however, that for sufficiently large problems, iterative methods for solving linear systems outperform direct methods. Fractional-in-space partial differential equations arise in models of processes undergoing anomalous diffusion. Unfortunately, as the fractional Laplacian is a non-local operator, numerical methods based on the direct discretisation of these equations typically requires the solution of dense linear systems, which is impractical for fine discretisations. In this thesis, novel applications of Krylov subspace approximations to matrix functions for both of these problems are investigated. Matrix functions arise when sampling from a GMRF by noting that the Cholesky decomposition A = LL^T is, essentially, a `square root' of the precision matrix A. Therefore, we can replace the usual sampling method, which forms x = L^(-T)z, with x = A^(-1/2)z, where z is a vector of independent and identically distributed standard normal random variables. Similarly, the matrix transfer technique can be used to build solutions to the fractional Poisson equation of the form ϕn = A^(-α/2)b, where A is the finite difference approximation to the Laplacian. Hence both applications require the approximation of f(A)b, where f(t) = t^(-α/2) and A is sparse. In this thesis we will compare the Lanczos approximation, the shift-and-invert Lanczos approximation, the extended Krylov subspace method, rational approximations and the restarted Lanczos approximation for approximating matrix functions of this form. A number of new and novel results are presented in this thesis. Firstly, we prove the convergence of the matrix transfer technique for the solution of the fractional Poisson equation and we give conditions by which the finite difference discretisation can be replaced by other methods for discretising the Laplacian. We then investigate a number of methods for approximating matrix functions of the form A^(-α/2)b and investigate stopping criteria for these methods. In particular, we derive a new method for restarting the Lanczos approximation to f(A)b. We then apply these techniques to the problem of sampling from a GMRF and construct a full suite of methods for sampling conditioned on linear constraints and approximating the likelihood. Finally, we consider the problem of sampling from a generalised Matern random field, which combines our techniques for solving fractional-in-space partial differential equations with our method for sampling from GMRFs.