A suitable method for journal bearing wear measurement

Purpose – Ideally, there is no wear in hydrodynamic lubrication regime. A small amount of wear occurs during start and stop of the machines and the amount of wear is so small that it is difficult to measure with accuracy. Various wear measuring techniques have been used where out-of-roundness was found to be the most reliable method of measuring small wear quantities in journal bearings. This technique was further developed to achieve higher accuracy in measuring small wear quantities. The method proved to be reliable as well as inexpensive. The paper aims to discuss these issues. Design/methodology/approach – In an experimental study, the effect of antiwear additives was studied on journal bearings lubricated with oil containing solid contaminants. The test duration was too long and the wear quantities achieved were too small. To minimise the test duration, short tests of about 90 min duration were conducted and wear was measured recording changes in variety of parameters related to weight, geometry and wear debris. The out-of-roundness was found to be the most effective method. This method was further refined by enlarging the out-of-roundness traces on a photocopier. The method was proved to be reliable and inexpensive. Findings – Study revealed that the most commonly used wear measurement techniques such as weight loss, roughness changes and change in particle count were not adequate for measuring small wear quantities in journal bearings. Out-of-roundness method with some refinements was found to be one of the most reliable methods for measuring small wear quantities in journal bearings working in hydrodynamic lubrication regime. By enlarging the out-of-roundness traces and determining the worn area of the bearing cross-section, weight loss in bearings was calculated, which was repeatable and reliable. Research limitations/implications – This research is a basic in nature where a rudimentary solution has been developed for measuring small wear quantities in rotary devices such as journal bearings. The method requires enlarging traces on a photocopier and determining the shape of the worn area on an out-of-roundness trace on a transparency, which is a simple but a crude method. This may require an automated procedure to determine the weight loss from the out-of-roundness traces directly. This method can be very useful in reducing test duration and measuring wear quantities with higher precision in situations where wear quantities are very small. Practical implications – This research provides a reliable method of measuring wear of circular geometry. The Talyrond equipment used for measuring the change in out-of-roundness due to wear of bearings indicates that this equipment has high potential to be used as a wear measuring device also. Measurement of weight loss from the traces is an enhanced capability of this equipment and this research may lead to the development of a modified version of Talyrond type of equipment for wear measurements in circular machine components. Originality/value – Wear measurement in hydrodynamic bearings requires long duration tests to achieve adequate wear quantities. Out-of-roundness is one of the geometrical parameters that changes with progression of wear in a circular shape components. Thus, out-of-roundness is found to be an effective wear measuring parameter that relates to change in geometry. Method of increasing the sensitivity and enlargement of out-of-roundness traces is original work through which area of worn cross-section can be determined and weight loss can be derived for materials of known density with higher precision.

Students' responses to the RACQ docudrama program

Young people are over-represented in road crashes and school-based education programs, including the RACQ Docudrama program, represent initiatives aimed at improving road safety among this high-risk group. The aim of the study was to apply an extended Theory of Planned Behaviour framework to understand more about the extent to which the program influenced individuals‟ intentions to speak up to a driver engaging in risky behaviours (e.g., speeding). Senior high school students (N=260) from 5 Queensland schools completed a survey in class. The study included a Control group (n = 86) who responded to the survey prior to completing the Docudrama program and an Intervention group comprising an Intervention-Immediate (n=100) and an Intervention-Delayed group (n = 74) who completed the survey after having participated in the program either on the day or up to a week later, respectively. Overall, the findings provided support for the beneficial effects of the program. Some of the study’s key findings included: (i) Intervention group participants consistently reported significantly stronger intentions to speak up than participants in the control group; (ii) among the significant predictors of intentions, a notable finding was that the more individuals anticipated feeling regretful for not having spoken up to a risky driver, the stronger their intentions were to speak up, and; (iii) the level of fear reported by students significantly decreased and was lowest at the conclusion of the program, following facilitated group discussion. The implications of the results for future research, program development and practice are discussed.

Footwear intervene of forefoot loading during landing movement

This study investigated the forefoot loading character under flexible sole condition while performing landing maneuver. Twenty healthy male volunteers have participated in the test. The insole and outsole loading were measured at the same time. The results of this study shown that the forefoot impact loading could be effectively relieved through the footwear during landing movement. The peak pressure value in the outsole was much higher than the barefoot, where the highest value in the first metatarsal of outsole was 63.6% higher than barefoot condition. Peak pressure of the third metatarsal of insole reduced the most, this has decreased about 51.2% of the barefoot experienced.

The Google Online Marketing Challenge: A Transnational Comparison of Classroom Learning with Real Clients, Real Money, and Real Advertising Campaigns

In 2008, a collaborative partnership between Google and academia launched the Google Online Marketing Challenge (hereinafter Google Challenge), perhaps the world’s largest in-class competition for higher education students. In just two years, almost 20,000 students from 58 countries participated in the Google Challenge. The Challenge gives undergraduate and graduate students hands-on experience with the world’s fastest growing advertising mechanism, search engine advertising. Funded by Google, students develop an advertising campaign for a small to medium sized enterprise and manage the campaign over three consecutive weeks using the Google AdWords platform. This article explores the Challenge as an innovative pedagogical tool for marketing educators. Based on the experiences of three instructors in Australia, Canada and the United States, this case study discusses the opportunities and challenges of integrating this dynamic problem-based learning approach into the classroom.

A comparison of DNA pools constructed following whole genome amplification for two-stage SNP genotyping designs

Genotyping in DNA pools reduces the cost and the time required to complete large genotyping projects. The aim of the present study was to evaluate pooling as part of a strategy for fine mapping in regions of significant linkage. Thirty-nine single nucleotide polymorphisms (SNPs) were analyzed in two genomic DNA pools of 384 individuals each and results compared with data after typing all individuals used in the pools. There were no significant differences using data from either 2 or 8 heterozygous individuals to correct frequency estimates for unequal allelic amplification. After correction, the mean difference between estimates from the genomic pool and individual allele frequencies was .033. A major limitation of the use of DNA pools is the time and effort required to carefully adjust the concentration of each individual DNA sample before mixing aliquots. Pools were also constructed by combining DNA after Multiple Displacement Amplification (MDA). The MDA pools gave similar results to pools constructed after careful DNA quantitation (mean difference from individual genotyping .040) and MDA provides a rapid method to generate pools suitable for some applications. Pools provide a rapid and cost-effective screen to eliminate SNPs that are not polymorphic in a test population and can detect minor allele frequencies as low as 1% in the pooled samples. With current levels of accuracy, pooling is best suited to an initial screen in the SNP validation process that can provide high-throughput comparisons between cases and controls to prioritize SNPs for subsequent individual genotyping.

Building an understanding of law: Engaging property economics students by using technology

It is assumed university students engage with technology as easily for their university studies as they do socially. However, prior research reflects the difficulties that non-law students face in engaging with legal materials. The purpose of this research was to determine how technology use impacts upon non-law students’ engagement with legal materials. The project explored inter alia the extent to which first year non-law students engaged with technology for their studies and in particular with legal materials and databases. The project was undertaken during semester 2, 2014 in a legal service unit delivered to a mixed cohort, which included construction management, property economics, planning and quantity surveying students. Actual technology use and familiarity was tested by means of an in class survey delivered in the Week 2 lecture. Use and familiarity was then retested at the end of semester in the Week 13 lecture, with adjustments made in lecture delivery and materials in-between.