A poroviscohyperelastic model for numerical analysis of mechanical behavior of single chondrocyte

The aim of this paper is to utilize a poroviscohyperelastic (PVHE) model which is developed based on the porohyperelastic (PHE) model to explore the mechanical deformation properties of single chondrocytes. Both creep and relaxation responses are investigated by using FEM models of micropipette aspiration and AFM experiments, respectively. The newly developed PVHE model is compared thoroughly with the SnHS and PHE models. It has been found that the PVHE can accurately capture both creep and stress relaxation behaviors of chondrocytes better than other two models. Hence, the PVHE is a promising model to investigate mechanical properties of single chondrocytes.

Development and application of Palygorskite porous ceramsite in a biological aerated filter (BAF)

Novel filter Palygorskite porous ceramsite (PC) was prepared using Palygorskite clay, poreforming material sawdust, and sodium silicate with a mass ratio of 10:2:1 after sintering at 700°C for 180 min. PC was characterized with X-ray diffraction, X-ray fluorescence, scanning electron microscopy, elemental, and porosimetry. PC had a total porosity of 67% and specific surface area of 61 m2/g. In order to assess the usefulness of PC as a medium for biological aerated filters (BAF), PC and (commercially available ceramsite) CAC were used to treat wastewater city in two laboratory-scale upflow BAFs. The results showed that the reactor containing PC was more efficient than the reactor containing CAC in terms of total organic carbon (TOC), ammonia nitrogen (NH3-N), and the removal of total nitrogen (TN) and phosphorus (P). This system was found to be more efficient at water temperatures ranging from 20 to 26°C, an air–water (A/W) ratio of 3:1, dissolved oxygen concentration >4.00 mg/L, and hydraulic retention time (HRT) ranging from 0.5 to 7 h. The interconnected porous structure produced for PC was suitable for microbial growth, and primarily protozoan and metazoan organisms were found in the biofilm. Microorganism growth also showed that, under the same submerged culture conditions, the biological mass in PC was significantly higher than in CAC (34.1 and 2.2 mg TN/g, respectively). In this way, PC media can be considered suitable for the use as a medium in novel biological aerated filters for the simultaneous removal of nitrogen and phosphorus.

On the symbiosis of law and truth in Christian theology: Reconciling universal and particular through the Pauline law of love

This article argues that the secular liberal and positivist foundations of the modern Western legal system render it violent. In particular, the liberal exclusion of faith and subjectivity in favour of abstract and universal reason in conjunction with its privileging of individual autonomy at the expense of the community leads to alienation of the individual from the community. Similarly, the positivist exclusion of faith and theology from law, with its enforced conformity to the posited law, also results in this violence of alienation. In response, this article proposes a new foundation for law, a natural law based in the truth of Trinitarian theology articulated by John Milbank. In the Trinity, the members exist as a perfect unity in diversity, providing a model for the reconciliation of the legal individual and community: the law of love. Through the law of love as the basic norm, individuals love their neighbours as themselves, reconciling the particular and the universal, and providing a community of peace rather than violence.

The dawn of the age of the drones:An Australian privacy law perspective

Suppose a homeowner habitually enjoys sunbathing in his or her backyard, protected by a high fence from prying eyes, including those of an adolescent neighbour. In times past such homeowners could be assured that they might go about their activities without a threat to their privacy. However, recent years have seen technological advances in the development of unmanned aerial vehicles (‘UAVs’), also known colloquially as drones, that have allowed them to become more reduced in size, complexity and price. UAVs today include models retailing to the public for less than $350 and with an ease of operation that enables them to serve as mobile platforms for miniature cameras. These machines now mean that for individuals like the posited homeowner’s adolescent neighbour, barriers such as high fences no longer constitute insuperable obstacles to their voyeuristic endeavours. Moreover, ease of access to the internet and video sharing websites provides a ready means of sharing any recordings made with such cameras with a wide audience. Persons in the homeowner’s position might understandably seek some form of redress for such egregious invasions of their privacy. Other than some kind of self-help, what alternative measures may be available?

Four generations of sequencing: Is it ready for the clinic yet?

Next-generation sequencing techniques have revolutionized over the last decade providing researchers with low cost, high-throughput alternatives compared to the traditional Sanger sequencing methods. These sequencing techniques have rapidly evolved from first-generation to fourth-generation with very broad applications such as unravelling the complexity of the genome, in terms of genetic variations, and having a high impact on the biological field. In this review, we discuss the transition of sequencing from the second-generation to the third- and fourth-generations, and describe some of their novel biological applications. With the advancement in technology, the earlier challenges of minimal size of the instrument, flexibility of throughput, ease of data analysis and short run times are being addressed. However, the need for prospective analysis and effectiveness to test whether the knowledge of any given new variants identified has an effect on clinical outcome may need improvement.

Investigating the factors influencing the adoption of m-banking: A cross cultural study

Purpose Little is known about the adoption of mobile banking technologies in emerging Asian economies. This paper aims to empirically examine the motivators that influence a consumer’s intentions to use mobile banking. Design/methodology/approach A web-based survey was employed to collect data from 348 respondents, split across Thailand and Australia. Data were analyzed by employing exploratory and confirmatory factor analyses, path and invariance analyses. Findings The findings indicate that for Australian consumers, perceived ease of use, perceived usefulness and perceived risk were the primary determinants of mobile banking adoption. For Thai consumers, the main factors were perceived usefulness, perceived risk and social influence. National culture was found to impact key antecedents that lead to adoption of m-banking. Research limitations/implications The actual variance explained by our study’s model was higher in Australia (59.3%) than for Thailand (23.8%), suggesting future research of m-banking adoption in emerging Asian cultures. Practical implications We identify the important factors consumers consider when adopting m-banking. The findings of this research give banking organisations a foundational model that can be used to support m-banking implementation. Originality/value Our study is perhaps the first to examine and compare the intention to adopt m-banking across Thai and Australian consumers, and responds to calls for additional research that generalises m-banking and m-services acceptance across cultures. This study has proposed and validated additional constructs that are not present in the original SST Intention to Use model.

Prevalence of alcohol-impaired driving and riding in northern Ghana

Objective The objective of this study was to determine the roadside prevalence of alcohol-impaired driving among drivers and riders in northern Ghana. The study also verifies motorists’ perception on their own alcohol use and knowledge of legal Blood Alcohol Concentration (BAC) limit of Ghana. Method With the assistance of police, the systematic random sampling was used to collect data at roadblocks using a cross-sectional study design. Breathalyzers were used to screen whether motorists had detectable alcohol in their breath and a follow-up breath tests conducted to measure the actual breath alcohol levels among positive participants. Results In all, 9.7% of the 789 participants had detectable alcohol among whom 6% exceeded the legal (BAC) limit of 0.08%. The prevalence of alcohol-impaired driving/riding was highest among cyclists (10% of all cyclists breath tested) followed by truck drivers 9% and motorcyclists (7% of all motorcyclists breath tested). The occurrence of a positive BAC among cyclists was about 8 times higher, (OR=7.73; p<0.001) and 2 times higher, among motorcyclists (OR=2.30; p=0.039) compared with private car drivers. The likelihood for detecting a positive BAC among male motorists/riders was higher than females (OR=1.67; p=0.354). The odds for detecting a positive BAC among weekend motorists/riders was significantly higher than weekdays (OR=2.62; p=0.001). Conclusion Alcohol-impaired driving/riding in Ghana is high by international standards. In order to attenuate the harmful effects of alcohol misuse such as alcohol-impaired driving/riding, there is the need to educate road users about how much alcohol they can consume and stay below the legal limit. The police should also initiate random breath testing to instil the deterrence of detection, certainty of apprehension and punishment, and severity and celerity of punishment among drink-driving motorists and riders.

Determining the drivers of m-banking adoption: A cross cultural study

This study empirically examines the motivators that influence a consumer’s intentions to use mobile banking. A web-based survey was employed to collect data from 348 respondents, split across Thailand and Australia. Data were analysed by employing exploratory and confirmatory factor analyses, path and invariance analyses. The findings indicate that for Australian consumers, perceived ease of use, perceived usefulness and perceived risk were the primary determinants of mobile banking adoption. For Thai consumers, the main factors were perceived usefulness, perceived risk and social influence. National culture was found to impact key antecedents that lead to adoption of m-banking. Interestingly, the actual variance explained by this study’s model was higher in Australia than for Thailand, suggesting future research of m-banking adoption in emerging Asian cultures. The findings of this research give banking organisations a foundational model that can be used to support m-banking implementation. This study is perhaps the first to examine and compare the intention to adopt m-banking across Thai and Australian consumers, and responds to calls for additional research that generalises m-banking and m-services acceptance across cultures. This study has proposed and validated additional constructs that are not present in the original SST Intention to Use model.

Use of modal flexibility method to detect damage in suspended cables and the effects of cable parameters

Modal flexibility is a widely accepted technique to detect structural damage using vibration characteristics. Its application to detect damage in long span large diameter cables such as those used in suspension bridge main cables has not received much attention. This paper uses the modal flexibility method incorporating two damage indices (DIs) based on lateral and vertical modes to localize damage in such cables. The competency of those DIs in damage detection is tested by the numerically obtained vibration characteristics of a suspended cable in both intact and damaged states. Three single damage cases and one multiple damage case are considered. The impact of random measurement noise in the modal data on the damage localization capability of these two DIs is next examined. Long span large diameter cables are characterized by the two critical cable parameters named bending stiffness and sag-extensibility. The influence of these parameters in the damage localization capability of the two DIs is evaluated by a parametric study with two single damage cases. Results confirm that the damage index based on lateral vibration modes has the ability to successfully detect and locate damage in suspended cables with 5% noise in modal data for a range of cable parameters. This simple approach therefore can be extended for timely damage detection in cables of suspension bridges and thereby enhance their service during their life spans.

RNASeqBrowser: A genome browser for simultaneous visualization of raw strand specific RNAseq reads and UCSC genome browser custom tracks

Background Strand specific RNAseq data is now more common in RNAseq projects. Visualizing RNAseq data has become an important matter in Analysis of sequencing data. The most widely used visualization tool is the UCSC genome browser that introduced the custom track concept that enabled researchers to simultaneously visualize gene expression at a particular locus from multiple experiments. Our objective of the software tool is to provide friendly interface for visualization of RNAseq datasets. Results This paper introduces a visualization tool (RNASeqBrowser) that incorporates and extends the functionality of the UCSC genome browser. For example, RNASeqBrowser simultaneously displays read coverage, SNPs, InDels and raw read tracks with other BED and wiggle tracks -- all being dynamically built from the BAM file. Paired reads are also connected in the browser to enable easier identification of novel exon/intron borders and chimaeric transcripts. Strand specific RNAseq data is also supported by RNASeqBrowser that displays reads above (positive strand transcript) or below (negative strand transcripts) a central line. Finally, RNASeqBrowser was designed for ease of use for users with few bioinformatic skills, and incorporates the features of many genome browsers into one platform. Conclusions The features of RNASeqBrowser: (1) RNASeqBrowser integrates UCSC genome browser and NGS visualization tools such as IGV. It extends the functionality of the UCSC genome browser by adding several new types of tracks to show NGS data such as individual raw reads, SNPs and InDels. (2) RNASeqBrowser can dynamically generate RNA secondary structure. It is useful for identifying non-coding RNA such as miRNA. (3) Overlaying NGS wiggle data is helpful in displaying differential expression and is simple to implement in RNASeqBrowser. (4) NGS data accumulates a lot of raw reads. Thus, RNASeqBrowser collapses exact duplicate reads to reduce visualization space. Normal PC’s can show many windows of NGS individual raw reads without much delay. (5) Multiple popup windows of individual raw reads provide users with more viewing space. This avoids existing approaches (such as IGV) which squeeze all raw reads into one window. This will be helpful for visualizing multiple datasets simultaneously. RNASeqBrowser and its manual are freely available at http://www.australianprostatecentre.org/research/software/rnaseqbrowser webcite or http://sourceforge.net/projects/rnaseqbrowser/ webcite

Young drivers’ responses to anti-speeding advertisements: Comparison of self-report and objective measures of persuasive processing and outcomes

Objective Self-report measures are typically used to assess the effectiveness of road safety advertisements. However, psychophysiological measures of persuasive processing (i.e., skin conductance response [SCR]) and objective driving measures of persuasive outcomes (i.e., in-vehicle GPS devices) may provide further insights into the effectiveness of these advertisements. This study aimed to explore the persuasive processing and outcomes of two anti-speeding advertisements by incorporating both self-report and objective measures of speeding behaviour. In addition, this study aimed to compare the findings derived from these different measurement approaches. Methods Young drivers (N = 20, Mage = 21.01 years) viewed either a positive or negative emotion-based anti-speeding television advertisement. Whilst viewing the advertisement, SCR activity was measured to assess ad-evoked arousal responses. The RoadScout® GPS device was then installed into participants’ vehicles for one week to measure on-road speed-related driving behaviour. Self-report measures assessed persuasive processing (emotional and arousal responses) and actual driving behaviour. Results There was general correspondence between the self-report measures of arousal and the SCR and between the self-report measure of actual driving behaviour and the objective driving data (as assessed via the GPS devices). Conclusions This study provides insights into how psychophysiological and GPS devices could be used as objective measures in conjunction with self-report measures to further understand the persuasive processes and outcomes of emotion-based anti-speeding advertisements.

The technological readiness of construction contractors

The Australian construction industry is often criticized for its comparatively low productivity. The most significant future productivity gains are predicted to arise from improvement in the firm’s project management. Information Communication Technologies (ICTs) are thought to offer such improvement. ICT adoption is particularly poor among Small and Medium Enterprises (SMEs). Existing studies provide only a general overview of adoption and diffusion of ICTs in SMEs, with no previous research measuring their readiness to adopt ICT. This paper outlines a theoretical approach to address this gap, exploring how to improve ICT adoption in Australian construction SMEs. A review of literature is undertaken to address the research question ‘What is the best conceptual approach to understanding ICT adoption in SMEs?’ The results emphasize the efficacy of a novel Technology Readiness and Acceptance Model (TRAM) to assess SMEs’ ICT implementation readiness. The proposed model consists of four major constructs to measure readiness comprising: - (1) optimism, - (2) innovativeness, - (3) discomfort and - (4) insecurity; two major constructs to measure technological acceptance comprising: - (1) perceived ease of use and - (2) perceived usefulness; and two extension variables comprising: - (1) self-efficacy and - (2) facilitating conditions. A limitation is that the performance of the conceptual model is yet to be tested empirically. Such research is planned in the coming year by the authors.

Determinants of the citation rate of medical research publications from a developing country

Background The number of citations received by an article is considered as an objective marker judging the importance and the quality of the research work. The present study aims to study the determinants of citations for research articles published by Sri Lankan authors. Methods Papers were selectively retrieved from the SciVerse Scopus® (Elsevier Properties S.A, USA) database for 10 years from 1st January 1997 to 31st December 2006, of which 50% were selected for inclusion by simple random sampling. The primary outcome measure was citation rate (defined as the number of citations during the 2 subsequent years after publication). Citation data was collected using the SciVerse Scopus® Citation Analyzer and self citations were excluded. A linear regression analysis was performed with ‘number of citations’ as the continuous dependent variable and other independent variables. Result The number of publications has steadily increased during the period of study. Over three quarter of papers were published in international journals. More than half of publications were research studies (55.3%), and most of the research studies were descriptive cross-sectional studies (27.1%). The mean number of citations within 2 years of publication was 1.7 and 52.1% of papers were not cited within the first two years of publication. The mean number of citations for collaborative studies (2.74) was significantly higher than that of non-collaborative studies (0.66). The mean number of citations did not significantly change depending on whether the publication had a positive result (2.08) or not (2.92) and was also not influenced by the presence (2.30) or absence (1.99) of the main study conclusion in the title of the article. In the linear regression model, the journal rank, number of authors, conducting the study abroad, being a research study or systematic review/meta-analysis and having regional and/or international collaboration all significantly increased the number of citations. Conclusion The journal rank, number of authors, conducting the study abroad, being a research study or systematic review/meta-analysis and having regional and/or international collaboration all significantly increased the number of citations. However, the presence of a positive result in the study did not influence the citation rate.

Open and closed-loop recycling of textile and apparel products

Textile waste is a significant contributor to landfill yet the majority of textiles can be recycled, allowing for the energy and fibre to be reclaimed. This chapter examines the open-loop and closed loop recycling of textile products with particular reference to the fashion and apparel context. It describes the fibres used within apparel, the current mechanical and chemical methods for textile recycling, LCA findings for each method, and applications within apparel for each. Barriers for more effective recycling include ease of integration into existing textile and apparel design methods as well as coordinated collection of post-consumer waste. The chapter concludes with a discussion of innovations that point to future trends in both open-loop and closed-loop recycling within the apparel industry.

Dystopian fiction for young people: Instructive tales of resilience

The rise and popularity of dystopian fiction in recent years is quite marked and critics often attribute such high sales of books and box office as being linked to the impact September 11 has had on the world, especially in the United States. While the events of September 11, 2001 saw a heightened anxiety by nations and their citizens about the fear and threat of terrorism – an anxiety which is paradoxically lowered and raised by increased surveillance practices, security checks and warnings – other changes since the last stages of the twentieth century have also raised concerns and anxieties. In this paper I use examples of Young Adult (YA) dystopian fiction to illustrate the potential these texts have for providing their readers with alternative ways of thinking about the challenges that others face and their capacity for resilience.